What's your voltage? [retired sticky]

[Jon]

Retired Sticky

Had a request for a poll on this and thought it would be interesting enough to see what everyone has running through their chips.

What I'd also like to know is what CPU speed you were able to reach, the motherboard or chipset used as well as if any volt modding was done to reach your VCore or if your voltage was adjustable via the BIOS.

If your exact voltage isn't listed, then just list it in your post...we're just getting an estimated average of what our forum members are using via the poll.

Let's see what you got!

Thanks go to {PMS}fishy for the poll idea!

[Yodums]

1.85v. No volt mod, since I have no experience w/ soldering stuff and I don't want my motherboard to be the first victim of many after I get my hand on that gun. Well I don't know what it was going to gain since I jumped on 1.85v right away.

Great Poll.

[{PMS}fishy]

Dang, you beat me for first post.

Volt Modded 2.05v on Epox 8KHA+

Max O/C before v-mod 1743mhz

After v-mod 1930mhz

[Jon]

2.12V modded on my Shuttle AK31 v3.1 (XP1700@1.72GHz) and 2.0V modded on my 8KHA+ (XP2000@1.83GHz).

Also run 1.95V jumpered on my 8K7A+ (Morgan 1GHz@1.35GHz) and two Asus MPX boards modded for 1.9V (each with dual XP1600@1.58GHz).

EDIT:

Have added since another 8KHA+ not voltmodded with an XP1700@1.65GHz using 1.85V and an Asus A7V333 with a Tbred XP1800@2.1GHz using 1.7V.

[Oni]

1.775 on the system in the sig. Need that to get my 12 multiplier working correctly. I voted 1.8, however. Seemed closer.

[SuperDave1685]

I got my Athlon XP 1600+ @ 1.650v. Its at 1.50GHz now, but I'm going to try to unlock the multipliers tonight. Its idling well now, at about 37C. Used to be 44C!!! I lowered the core to help the heating. I'm also going to get a case fan and make me a blow hole tonight I hope. Any ideas on better air cooling methods?

[adamtekh]

a better heat sink , or maybe just lapping that 6cu+

every 6cu HSF fan ive seen needed lapping

and your useing artic silver II / III ?

[dropadrop]

My old xp1600 hardly overclocks, so I just put it to 140fsb and put the voltage as low as it will go on my 8kha+...

[ratts]

xp1900+ @ 9.5xmult. with 166fsb. using 1.75v. running great. i want to jump to 10x but not sure about raising volts. seems everytime i did hangs and crashes followed it. or maybe it is me choosing wrong combos. oh well, default 1.75v is where i am at.

[hellrazrblade]

i'm at 1.85v running 10.5*152 (1602mhz) but thats rock hard stable. ive been over 1700, but its kinda pointless because it isnt stable. Antec PP-352X psu (350w). KR7A-133R. 512mb Cheapo (Newtrend tech) triple2 2100ddr. 1700+ AGOGA 9 0205

[Yodums]

Back to default. PSU has been a PITA with lots of power off the vcore since it always brings down the 5v. I lost about 6fsb, but that's a good giveaway for stablity.

[Cown]

1.85, no volt mod :D

[Wega!]

2.05V :p

[shogan191]

XP2000+ 142x13 and 1.85v.=1846
slk800w80mm4200rpm.
temp39.5C/44.5C under prime95.

[rogerdugans]

2.1 on this rig- 2 others volt modded. 1 is at 1.9 and the other is 1.8 right now.

[Silver]

XP2200 @ 185 x 12 @ 1.95v = 2,220Mhz

[takiwa]

stable @ 1.75 (default) - 148 x 10.5 = 1554MHz

stable @ 1.85 - 180 x 10 = 1800MHz

XP1600+ AROIA "Y"

[eobard]

1.85v until I can finally get fittings on my waterblock, then 2.1v here I come!

[Asheron]

1.85 vcore clocking my 1700 to 1.7ghz

[nevamind]

2000+......running at 175..........and i up it to 2.2 and it's at 2.331

[packratbob]

xp1800@1867 162fsb vcore2.1
h20 cooled on 8kha+ i have crap steping and it wont go higher i need an agoia or better

[honedbone]

1.95v on Tbird1.4@1.7 (10x170)
Had to go to water after heatsink fan failure led to thermally damaged CPU. Pretty impressed with this processor. Ran for probably an entire night with no fan (and believe me, that sucker was hot when I finally got to it). Computer seemed dead, but after switching molex connection for the fan, it booted right up. Unfortuneately, at stock settings and voltage, it was running at 50degC at idle. It wouldn't boot with any attempt at oc. But with water system, I'm back at it. So much for Tom's Hardon's video of AMD proc dying without fan.
Maybe it was the entire h/s, but the site seriously bites now.
How's that for a drawn out vote?

[DiaperGravy]

Hi, I have been observing these forums for a while, and figured it was time I registered heh….
Any who, just wanted to take this opportunity to thank all those who have helped individuals unknowingly like myself by posting their findings here. Now if I could only get a good cable line for the net, I would be set! LOL
And yes… I’m certain I will have many questions in the future, but for now I just wanted to say, thank you all, very much.

Thanks again :D

DiaperGravy:cool:
:eek: Ohyeah I use 1.75v standard Unless I can't make post... heh

[Demont]

1.65v here, im running it low because my motherboard is a lemon and i cant overclock past 138 stable. so i just lowered voltage and now im running 3-4 degrees cooler... i dont much care about my 70mhz overclock!:rolleyes: my cpu is a good stepping so it doesnt mind the low voltage. 1.6 made it unstable though.

*update*

running at 1.75 now with the o/c in my sig. had to unlock this beastie.

[ezeKieL987]

1.80 at the settings in my sig...but when i get my chip backed (unlocked thanks to Illah) i might have to bump it up cause i want the highest possible OC...:p

[Da_Bear]

1.8v xp1800+@ 1750Mhz AROIA '9'

[v8440]

Tbird 1.33 @ 1632, 2.19V. Running AK31 v3 with volt mod, koolance case.

[tom_ozahoski]

1.65v on a 1600+ @1600mhz

[Mr. $T$]

1.86 volts NEED more!!! mobo max!

[Denubius]

My xp1500+ (AGKGA) :burn: 10mult. with 160fsb,vcore 1,725
and it's rock stable :D

[res0r9lm]

I voted for 1.95, I have mine set to 1.97@1760 right now but has been to 1810 with 2v

[maxima88]

1.85v which is the max on my a7v333 w/out disabling the voltage limiter option on my mobo which will take my vcore to 2.1v ~2.2v
which I don't really wanna do or need.

System is in my sig and running stable at 1.85v.:)

[Viper67857]

set at 1.80, getting 1.824. Highly stable @ 1667 (145x11.5) running 100% usage (F@H) 24/7. The only time this system hangs is when gaming, and I think that's because I pushed my 8500 a little too hard on the OC's a few times and have caused some slight damage to the core.

[RnPgrosz]

Ok, I am doing 2.2v on the epox 8k3a+ (KT333 chipset and no volt mod required). I have my XP 1600+@2009 MHz.

[Demont]

wow dude do you have a WCPUID shot of that? 609mhz is a huge overclock!!! (mmmm i would like to see some intel crushing benchys too...) do you already have a thread on this?

[RnPgrosz]

Originally posted by Demont
wow dude do you have a WCPUID shot of that? 609mhz is a huge overclock!!! (mmmm i would like to see some intel crushing benchys too...) do you already have a thread on this?
Good idea, I'll start at thread in the amd cpus section right now.

Edit: Here is the thread.

http://forum.oc-forums.com/vb/showthread.php?s=&threadid=115268

[the_poche]

My xp1600+ got 1.75 vcore running at 1548(172*9). I can get it stable at 1634mhz but for everyday use , I leave it at 1550(have to give it a rest, its an old AGKGA:D )

[gtsimmo]

XP1800 Agoia 143 x 12.5 @ +0.05 on a Soyo Dragon Plus

[LinkStatic]

1.85 V.... cant go higher coz my full load temp is already 49 oC.... and its the max that my mobo supports.... volt mod? not yet, but considering if I can have a better HSF....

[ZeroKelvin]

1.85v with no mod on my Asus A7N266-C, but getting my Epox 8K5A3+ in a day or two. So looking to be up around 2.0v then.

[DarkJediSleikas]

Duron 700 @ 950 @ 1.8V with basic cooling (60mm fan and a small aluminium heatsink)
Epox 8KTA+ motherboard KT133 chipset

The nice thing about having an old, slow AMD is that it runs so cool :) . The idle temp is as low as 33C, and under a heavy load, it will never get past 50C.

[NascarFool]

I picked 1.8v but I'm at 1.775v for my XP2200+ at 11x181.:)

[james.miller]

i picked below 1.75

im at 1.73volts and 11.5*142.7 = 1640mhz

[residentevil2]

it wont let me in thier it says i dont have permission whats up ???


But i was on 1900 mhz w/o vmod now im on 2014 mhz with 2.19 vcore

[NevadaGold]

Abit KX7-333r
Volt modded to 2.03
1.2 AXIA T-bird @ 1.52ghz

[JAWS]

Gotta pump 2.1 into my 1600 to get over 1800.

[juliendogg]

xp 1600 @ 1900 (152X12.5) @ 1.95. shuttle is v. modded. was running 1850 stable @ 1.85. don't know how high i could go now, as i'm on my highest available multi and i can't keep my system stable at a higher fsb. this is a recent development and i'm not sure why, as i've always run this board at 166 with fastest ram timings, i'll figure it out eventually, probably ram/psu or both.

[radadman]

How about the highest overclock with the least voltage?
I can run 100% stable with only 1.65v 10.5 x 166=1.74GHz
or 1.7v 11 x 164=1.8GHz using unlocked xp2000

[LocutusofBorg]

running stock at 1.76 ATM
will OC next week and see what i get
BTW XP2100+

[quegyboe]

1.85v on my Duron 1100 @ 1200. Stats in sig....

[Demont]

wow you use 1.85 just for a 100mhz overclock? is it really neccesary... is it unstable otherwise?

[Elmolivez]

I am currently running rock stable at 1.75v

XP 1700+ (O/C 1650), 256 MB PC2700, WD 30GB, GF4 4200 (O/C 318/565) No other cooling other than normal fans 3x 80mm. Thermaltake minisuperorb heatsink. Cable Modem 1.5 Mb.

[Stedeman]

1.85v for me

[Erasmus]

1200 TB @ 1999

1.51V(bios reading), 1.57V(MBM).
Adjusted in bios. 1.55V is the lowest setting it has.
Been running stable about a year now.
Temps lowered 3-4C.

[filip04]

1.92, im running my xp 1600+ at 1.64 GHz... 10.5 x 156 FSB if i remember right... 45 degrees core temp...

umm, i don't know how to unlock the multiplier.... well, i do, but i don't have the multiplier in my bios.... would that be a problem for me??? i can't find it anywhere on my mobo either.... help

oh yeah, my mobo is a GA-7VKML

[water_cooler 20]

I'm getting a epox EP-8K5A2+ with an amd xp 2200 with a water cooler i want to know if i should max out the volts or not when i get it.I think the max is ether 2.1 or 2.0

[beezee]

specs in sig @ 1.75
need more voltage! :)

[OSUmaxx]

Specs are in the sig. I'm still @ 1.75V and running 100% stable.

172FSB x 10.5

[fender123]

Well, i'm at stock 1.75 now... contemplating changing my Volcano 7+ to a Slk-800 with Tornado jet engine loud ass mo@@#^ fan hehhehe :)

Also trying to wait for the new Swiftech MCX462+, hope it's good :)

[nightowl]

After reading through this thread I have been messin with voltages and have the system in my sig running 100% stable @ 1.7V. load temps now 47C (on die) :D

[recbo]

FSB 40C @136

Somebody here has a 1600+ running faster
at lower volts than my water-cooled 1900+.
This one is rock solid, though, and fairly
quiet for the power.

-Bob

[Nikoror]

My T-bird 1200@1360 abit kt7a (via kt133) volt. 1.8v
fsb=143mhz

[OC-Master]

I got my 1GHz Athlon clocked 100% stable at 1.47GHz and I'm using 1.975Vcore with the Volcano 7+. Even under the hottest room temperatures, my cpu never exceeds past 45c.


DS-Master

[recbo]

I doubt that heat is what is causing problems
with my XP1900+ when run over 1.64Ghz
12 x 136 FSB or 12.5 x 133, 45C. Maybe I should
look at linux and the VIA chips. When I last
tried to go higher my errors were virtual
paging kernel oops and in the boot messages
there was "Unrecognized VIA south bus".
Now I have up to date source code and
should try again. I have hard drive recognition
problems even with kernel append= specific
instructions as to which bios number i.e.
0x80 or 81 or 82 or 84 or 84 or 86 is drive
/dev/hda. I don't know if the raid chip
is recognized.

Meanwhile slightly paraplegic linux is running
stable and serving my network. I can't do
things that crash it all the time but I should
find out if new source code keeps the kernel
up with faster settings. HTC code updated.

Gotta go to get nvidia kernel source, too.
Some is in there but there are some others
with documentation and utilities for OC'ing
nvidia, 2 or 3 nvidia packages http://www.debian.org

-Bob

[Kamerat]

I'm running an Athlon MP 1.2GHz @ 1.67GHz (9.5x176MHz) with the voltage of 2.1V (MBM showing 2.11-2.16V). It's aircooled with a Taisol CGK760 with a 120mm fan 12V @ 24V. :D

[Rottys-R-Us]

:D

[Kamerat]

I miss my 8KHA+... I wrecked it a week after I repaired it (replaced a defect mosfet and resistor). I connected a device that i used to bypass the overcurrentprotection wrong way :( . I actually ran my MP with 2,38V on that board, but only @ 1,2GHz.

[SafirXP]

Had an unlocking accident.. so my AthlonXP 1700+ (default 11.0X) is locked at 7.0X, so the vcore is set to 1.725! So basically I'm running a 937MHz AthlonXP! :(

Tried cleaning off the conductive ink (which I guess I can't see with my naked eyes), again and again with no avail!

[Pyros]

1.85v on a soyo dragon ultra, xp1600 running 147fsb x 12.5@1838mhz. its stable, up 4 degrees from stock, and cooled with air.

[newbie]

1.8 vcore - 1700+ Unlocked running at 1600 mghz 266 bus ,air cooled will boot as 1900+ but unstable even with 1.85(highest available) vcore.

MSI K7T266 RU
GEFORCE 3Ti

[The Coolest]

Although I'm now running at stock speed an vcore, the proc is just extremely hot now. I'm gonna do something about it and winter is coming, so I'm hope that I'll be able to go to 1400+ @ 1.85v. I selected 1.85, coz that's the core voltage I'll be running soon enough...

[Sworkhard]

I'm at 1.85 volt on a athlon xp 1800+ (done with pencil trick because my current mobo abit kt133a (to be replaced soon) doesn't support user changable voltage. Managed to get the thing to run at 1850 at this voltage though. It too bad that there was only a 5% perfomance differance from at 1533 though because of the pc133 ram.

[Sworkhard]

my parents computer (tbird 1000/100 AVIA w/ abit nv7 133-r) does 1580 mhz at only 1.8v (the highest the board goes on a locked cpu). Can't run it for long at this speed though because of the poor heat sink (50 C at 1000, shows about 75 right after booting at 1580 and is rising so it has to be shut down but when I tried it with my own tt volcano 7+ it did only 47 C and was stable)

[DAGO]

Running this 1.4 Athlon at 1.5 with a vcore of 1.80...Have had some trouble getting accurate readings on what the vcore actually was, but MBM5 solved my dilemma...:rolleyes:

[Cowboy X]

My t'bird 1.4 is running at 1536 @ 1.75v

[Maximouse]

I have an 1800+ on an Asus A7V333 MB.

Funny, I have the voltage set for 1.75 in the bios setup, but its reporting 1.8v?

[Yodums]

I wish I could revote! I'm currently at 1.85v :D

[rippedsocks]

t-bird 1ghz @ 1.4 1.95v 9x156
a7v133

[minoukat]

2.4v (no, I'm not crazy, it's a K6-2 chip ! :D)

[CalsonicGTR]

Well, mine is listing at 1.75 volts right now. I think that is pretty good

[Millum]

1.80 as my sig is,but if i raise the fsb to over 171mhz 1.85v

[Evc]

Originally posted by {PMS}fishy
Dang, you beat me for first post.

Volt Modded 2.05v on Epox 8KHA+

Max O/C before v-mod 1743mhz

After v-mod 1930mhz Call me stupid or something, but what exactly does a voltage mod do?

I gotta say, an extra ~200MHz froma mod is sweet!

Me, Im running @ 1.8V on my XP 2000+ AGOIA, 10x181

I have 1 stick of Corsair XMS PC3000DDR, is it possible to hit a 200FSB with that?

Also, using a Epox 8K3A

[OC-Master]

Originally posted by Evc
Call me stupid or something, but what exactly does a voltage mod do?

I gotta say, an extra ~200MHz froma mod is sweet!

Me, Im running @ 1.8V on my XP 2000+ AGOIA, 10x181

I have 1 stick of Corsair XMS PC3000DDR, is it possible to hit a 200FSB with that?

Also, using a Epox 8K3A , a voltage mod allows you to venture behond 1.85V (Standard max) and go up and even over 2Volts depending on what resisters you decide to use.

My motherboard allows me to go as high as 2.1V after the mod and before the mod, I was limited to 1.85V

1.85V got me 1.4GHz, by raising the voltage to 2.05V, I am running smooth at 1.5GHz.


DS-Master

[LittlePiggie]

t-bird 1300 @1367 137fsb and 1.6 vcore. This is the first installment, setting up a killer pelt system. :D

edit:

1484 :D
45c idle 49c load
1.7 vcore 135mhz fsb

[recbo]

A new dog or a shotgun or voltage mod
may be necessary to handle those AOL
CD's.

I ran my XP1900+ for a week at 1.775v
12x136 but had some trouble and then
upped it to 1.8v and it's been OK since.
I have my highspeedpc PC2700 on all
the cas2 and interleave 4 optimizations
and all the other mem settings.

Is it best to use edge(northbridge) or
center(cpu) whatzit control? I have
the fast command decode, maybe
ought to try ultra as everything is
fine.

[Fever]

1.82 seems to be this CPU's sweet spot.

[specific]

my 1800 doesn't like higher than1.825 settings, which is really 1.85+ in the mobo monitor. i'm cought in between so i just chose 1.85, cuz that's what it's closest to in actuality.
although that was with the old hs. my cpu relocked itself, and i'm waiting for a new mobo to unlock it again. so my results could be a little different next go round.
as for now, abit kr7a-raid. but by next weekend, abit kx7.

[MikeTimbers]

XP2400+ at 1.75v
XP1800+ at 1.85v

[Hugovsky]

It's all in my sig

[LittlePiggie]

****update****

Just made a duct out of dryer tubing and an 80mm fan running from my window.
Got up to 1680 last night @ 38 degrees celcius load. :drool: :burn: Oh yeah.
here's the stats:

vcore 1.8
fsb 138
multi 11? 11.5? Forgot, hafta do it again tonight!!:D:D

[HardwareJedi]

Normal everyday overclock is XP2000+@1893Mhz @1.825v
Max stable Overclock XP2000+@1919Mhz@1.95v
Max Overclock w/some issues, but runs through 3dMark 1956Mhz@2.00v

[TyRex]

I run my 1.2 tbird at 10*150(load 48C) with a 2.0 Vcore with my kingston pc2100. The other night though, I got it up to 9.5*165 by raising the PCI latency. It'd boot fine, but I kept getting little program errors here and there.

[viper_wc]

I got my TB1200@1450 145fsb running at 2.2V on a KT7A with volt mods.

With 2 120mm fans, my temps are now 35C idle/45C load.

[Spacemonkey]

I would like to see the +12 and +5v specs that you high oc'ers have. Post some please.

[recbo]

I had a water problem and fried my 1900+ on KR7A-133R,
so temporarily I moved my highspeedpc.com pc2100 over
to a Shuttle box running a second 1900+ AGOGA. I set
the ram settings the same, basically every setting at
max, cas2, 4 interleave, best numbers all through, and
even at fsb 133 that won't work. The highspeedpc
sticks are based on tested samsung 6ns chips. This
might just mean I have to raise my ddr voltage from
1.75 or whatever, but there's no way on the Shuttle
xpc. Shuttle xpc mboards have a lot of options that
are nice for OC'ing, but voltage is one of the first
things we need to have control over, and you can't
set the voltage up.

There might be a hint that future bios will allow
voltage setting, because cmos has an item for
Frequency and Voltage, but go in there and it's
only frequency.

The heat pipe thing is nice but my temp is higher
than with watercooling, and I had gpu and hd
on my watercooling radiator with cpu. Temp is
minimum 44C with no overclock, and with water
I was at 43.6 to 44.5C max with 5% OC and
add 4C for each 5% more OC. I put arctic
silver grease on the cpu in the Shuttle, and
arctic silver epoxy with the KR7A-133R setup.

I like that TyRex avatar, it expresses the soul and
essence of hacking. I unlocked a 1900+, fried it
when my water ran a little low, retired my first
four pc2100 sticks due to only one working in
the KR7, HPT raid controller went out, several
hard drives lost to water-cooling experiments
before I figured that out, flogging myself trying
to get a driver for linux Xserver on the Shuttle's
VIA Savage chip. Linux is like that, too, but
when it's working, wow. Yesterday I was
compiling X from source on the Shuttle box,
and at the same time serving mail and web
proxy and webserver and dns, no glitch
anywhere, while my win pc was gulping and
belching and puking just to download email
and get it organized, outlook crashing when
symantec scanned email for viruses. puny!

At the autoparts store, same story, throw
away four LED tail and brake lights and
two new tail light housings due to poor
quality control, kludge with caulk to get
the old tail light working, dodge the cops
to get it inspected where a man got shot
by a sniper.

My new 1900+ is only AGOGA but has SMP
stuff that linux can use for one processor.
Linux likes that, and the RTL ethernet chip
in the Shuttle xpc.

That Shuttle box needs source code hacking
on drivers for display and audio and ata133.
A few days there but at least the RTL ethernet
chip was no problem.

I'm actually using the shuttle xpc for a firewall
but it has an agp slot, 8x I think. If they add
voltage control to cmos...power supply is only
200 watts, though, more hacking required!

[Voodoo Rufus]

I'm at 1.85V on my Tbird 1400. I know how to solder but I don't like the idea of taking my CPU any further than that.

[Namagomi]

Originally posted by Silver
XP2200 @ 185 x 12 @ 1.95v = 2,220Mhz

Oh, holy crap!

That's quite the clock for a 2200+ :D

[wuzzapiman]

2400+ @ 183.37x13 = 2384Mhz
2.1 vcore

[The Doors]

Everything in my Sig ;)

[sushi]

My AMD 1700+ runs stable at 1623 mhz, default voltage, stock HSF.

[loudblaster]

1.85v Duron 1100 @ 1200

Epox 8k7a+ lowest it goes, I can go to 2.2 with no mods :D

had problems with memory, now i'll try some overclocking! :D

[hdj]

a7m2626-d board with two early xp1800+. It's a combination that does not clock higher than 137 fsb stable, so I just run it at 1.7V/135fsb

[ChillPhatCat]

It's kinda funny that I bought my 1600+ and decided it had to go 1700 or higher or it was a crappy chip... so I pushed and pushed and after discovering it was stable at 1827 and 1.95V I decided running at 60C under load was a bit much.... So I'm at 1780 and 1.9 @ 51C under load... I guess 380 MHz is a pretty good air cooled over clock :D

I Can go all the way to 2.05V w/o mod though... I fully plan to when I get the water cooler up and running.

[maxima88]

I did the overvolt mod that hoot did. Now I can vary my vcore from 1.89v to 2.29v.

Highest I've gotten to is 2037MHz w/ my XP1600+ AGOIA.
Everyday speed is 1858mhz at default 1.79vcore.

[SpyderMatrix]

Originally posted by DiaperGravy
Hi, I have been observing these forums for a while, and figured it was time I registered heh….
Any who, just wanted to take this opportunity to thank all those who have helped individuals unknowingly like myself by posting their findings here. Now if I could only get a good cable line for the net, I would be set! LOL
And yes… I’m certain I will have many questions in the future, but for now I just wanted to say, thank you all, very much.

Thanks again :D

DiaperGravy:cool:
:eek: Ohyeah I use 1.75v standard Unless I can't make post... heh

First off Welcome to the Forums and to the Addiction!

[aNtraXx]

now i just have 1,95 vcore cause im still cooling with air

[David]

Undervolted, currently at 1.58V according to Speedfan. Dual XP1600+s at stock speed.

I need less heat so I can reduce the noise a bit.

Rock solid at that voltage. I may try taking it down some more. The PC has been folding 24/7 for two days non-stop so it should be stable at this Vcore.

David

[gazzrawly]

AMD Athlon 2100XP - VC = 2.2 Stable @ 2.53ghz

[Demont]

Originally posted by gazzrawly
AMD Athlon 2100XP - VC = 2.2 Stable @ 2.53ghz
:eek: what kind of cooling?

[catsbuddy]

Xp1600+ AGOIA 202MHZ x 9.5 = 1919MHZ.
EPOX 8K3A, 1.9 volts, Corsair XMS3200 CL2, SK6 + funnel + Delta 80mm 80CFM, cpu at 40 degrees C, MB at 27.
1.95 volts gets me a couple more mhz, but I'm chicken to run it that way.

[Decaf]

vCore 1.85
vDimm 2.85

MBM +5 reads 4.97
+12 reads 11.98

Almost never varies more than this
Antec Truepower 330

[AMDXP]

Running at 1.75V.

Running p3 1Ghz.

[AMDXP]

O crap!

This poll is for AMD chips!

My bad.

[rickd]

vcore 2.0 2400+ 200X12- 2400mhz

[Squelch Oil]

I just purchased one of the XP1700+ with the .13 micron core. I have managed to get it running with 166 FSB at the default 12 multiplyer. It seems to run right around 107F with the voltage at 1.75. I am curious though, it sounds like the older chips used a higher default voltage, this one defaults to 1.5 and the max this A7N8X board will allow is 1.75. Should I try to mod the board to push a higher voltage? Also, although I see a lot of info on the older cores I haven't seen much in here about what is a safe temperature for these new ones. I would love to hear any feedback.

[Demont]

Originally posted by Squelch Oil
I just purchased one of the XP1700+ with the .13 micron core. I have managed to get it running with 166 FSB at the default 12 multiplyer. It seems to run right around 107F with the voltage at 1.75. I am curious though, it sounds like the older chips used a higher default voltage, this one defaults to 1.5 and the max this A7N8X board will allow is 1.75. Should I try to mod the board to push a higher voltage? Also, although I see a lot of info on the older cores I haven't seen much in here about what is a safe temperature for these new ones. I would love to hear any feedback.

that board allows 1.85, maybe check the bios again?

thats a big increase from 1.5, i wouldnt worry about more voltage.

the processor you have is the same as the 2200+'s but just with a lower multiplier so pretty much the same things apply..... i would expect about 2 gigs from that chip, 2.1-2.2 with good water/chiller cooling. good luck.

[Squelch Oil]

Hey Demont thanks for the reply. I know it is supposed to support 1.85Vcore, but I swear, it doesn't show anything higher than 1.75 as an option. One thought though, most of you talking about 1.85 sound as though you have chips that run at a default Vcore of 1.60, my .13 core defaults to 1.50, so maybe ASUS has the BIOS set to allow an increase of only .25 above default. I am running the beta BIOS that ASUS released Friday, I am not sure if the original G BIOS would allow a higher overclock. I would load it back on and try, but since my current cooling is only allowing me to run at 1.725 stably I won't bother to try until I get a better cooling solution. I am off to troll the board for a heat sink recommendation now =) I am thinking about the Coolmaster HHC-001

[Crappy]

XP 2400+ AIUGB Week 45 running on my Epox 8RDA+ at 2500 12.5x200 Vcore 1.85 +12= 11.98 +5= 5.03

[Demont]

Originally posted by Squelch Oil
Hey Demont thanks for the reply. I know it is supposed to support 1.85Vcore, but I swear, it doesn't show anything higher than 1.75 as an option. One thought though, most of you talking about 1.85 sound as though you have chips that run at a default Vcore of 1.60, my .13 core defaults to 1.50, so maybe ASUS has the BIOS set to allow an increase of only .25 above default. I am running the beta BIOS that ASUS released Friday, I am not sure if the original G BIOS would allow a higher overclock. I would load it back on and try, but since my current cooling is only allowing me to run at 1.725 stably I won't bother to try until I get a better cooling solution. I am off to troll the board for a heat sink recommendation now =) I am thinking about the Coolmaster HHC-001

i dont know about your voltage theory, i've never heard of that. but, cranking it to 1.85 probably won't yield you any more speed anyway.... probably. maybe like 100mhz more maximum.

also, i have a thermalright slk-800, and a thermaltake smart fan 2.... arguably the best heatsink and the most well-rounded 80mm fan on the market. (it can do 75cfms which is almost the fastest heatsink on the market, but it also has a variable speed thing built in and its not too loud). thats my suggestion there, its a freebie, no trolling neccesary. :D



ps. hey crappy i think your sig is too long

[Squelch Oil]

Thanks for the advice. I already bought the Cooler Master HHC-001 and wow, my temps dropped from mid 40s to right at 30 tops. I still can't get the thing past 1800MHz though, but hey, that's not to bad for a $60 investment. I'll buy a 2600 when they get below $100.

Signed,
Da Cheap Bastad
:D

[Crappy]

Originally posted by Demont


ps. hey crappy i think your sig is too long

Is that better? :)

[FishNiX]

I have :

TbredB 2400+ @ 2100mhz (140x15) @ 1.65V
Epox 8kha+
2x256MB Crucial PC2100

Cutom watercooling rig, runs at 38C under full load (RC-72) and around 30 at idle (i think...its never idle)

Still needs some work, I think. I recently rebuilt the watercooling setup -- just reran the lines and reset the waterblock on the CPU -- and it got me from 135mhz to 140mhz, so me thinks there is still a ways to go.

I run memtest86 to check stability, although it doesnt seem to be dependent on my memory, as over 140 fails no matter what timings I use and no matter what voltage I set the ram to.

I think I need a new waterblock...but I dont wanna drop a lot of cash on it right now ;)

[Pruss]

1.65 on TBredB2100+(AIUHB). So far up to 2158Mhz, but still lots of room left.

[Furious]

Newegg 2100+ at 2ghz using 1.65 volts on a KR7A-133RAID. Unfortunately this motherboard only goes to 1.725 volts with the CX bios. This chip will post and partially run 3dmark2k1 at 2158mhz. Of course the problem could be the odd PCI and/or AGP setting I'm forced to use with this board. Looking at the EPOX board to get the most out of it.

[BTank]

similar to gaxxrawly. 2.5ghz 2100+ 1.875v

[trenchypost]

1.85V on my celeron, up from 1.7V originally

[icedogg9999]

my 1.33@1.4 T-Bird is at the default voltage, probably 1.7v, it runs perfectly, I can go up to 1.85v, I only use that when I overclock.

[Furious]

Update. New motherboard (8RDA) and now I'm running 2.2 ghz at 1.8v. I'll let it run here for a while and then try higher.

[Wimbo]

default atm

[kentarou]

running my newegg 2100+ Yr '03, week 2 AIUHB at 2.01v w/ Danger Den water cooling Maze3 kit.

Asus A7N8X Deluxe Volt Mod, Uber Bios 1002-001, 2.47GHz at 190FSB*13. Memory Timing 3/2/2/2

Prime95 Torture Max CPU Temp: 53/125
Mobo: 40/104

Rock Solid Stable.

[hrdwrjnkie]

1.9v according to MBM, 1.85 according to the Bios, running a JUICB 1700+ at 2079MHz, 30 degrees on die under load and rock-solid stable. ThermalRight SLK-800 w/80mm Sunon at 84CFM:)

[xhwfed]

Iv got a crap CPU at the moment, Duron 1000Mhz, But I gotten it to 1.4 Stable @ 1.76V

[FishNiX]

Hey man- that's not crap, i just installed a Duron 950 in my younger brothers comp and he loves it!

we all use what we can afford and need. i ran a duron 650@900 for a LONG time. until about a year ago.

no worries ;)

later!

[c0nfusion]

xp2100+ @ 2210 ghz (170x13) @ 1.7v

[freshy98]

Mine is 1.76V and I have mine volt modded all though it's not really nescesarry. Maybe when I unlock the CPU I might need it.

Max OC at the moment is 2005MHz from 1800MHz default (2200+).

[Banshee164]

XP1700+ @ 2310ghz - 1.925v

[doesnotcompute]

Athlon XP 2000+ @ 1860MHz with 1.85v.

[dude_drew]

2.8v when I have my AMD in. (K6 200MHz). 2.9v when my Intel 200MHz w/MMX is in. It's socket 7 and ancient technology but it works. Waiting to get a job to upgrade...being 14 sucks.

[jconforti]

see below....

[dnycompbuilder]

hey sporting a 2000+xp tb on an a7v8x @1921mhz (11.5X167/34) running prime 95 torture and hitting 35c with a voltage of 1.87 Took it all the way up to 1956mhz with a multiplier of 12.0 and fsb of 163 but wouldnt hold stable, not willing to raise the voltage anymore than what its at so guess its not gonna reach that speed, unless i raise my multiplier but im not willing to sacrifice the fsb speed.

[The Doors]

XP1800+ JIUCB @2.2Ghz 1.95v (MBM reports 1.97-1.98v)

Adriano

[SoulKlekta]

Athlon T-Bird 1400@1608 (12 x 134) 1.75v set via BIOS,
Thermal Take Volcano 9 h/s/f,
Asus A7A266DDR

[black_wing]

check out my sig!!! :p

[walldow]

2600+(333)@2500mhz, 2.1volts
2100+t-bread@2500mhz, 2.0volts

i have took both chips to 2.3volts!

[AirOgre]

Currently stable @ 11.5x200 @ 1.9v, im not willing to go any higher than that voltage on my SLK-800 w/ volcano 9, load temp: 46C with fan turned to a decent level, 43C with fan turned to highest

[AAdjuster]

XP1600+@1933 1.9v

[verbatim]

1.725v xp2400 @2100ghz msi kt4.

The highest voltage available on this board is 1.750, does anyone know how to increase this as there is more overclocking potentual here?

[mook]

1.85 volts....it's in the sig. :)

[parkinglot]

Does anyone know a good configuration for maximum results with the FSB, CPU Voltage, and CPU Ratio??? My voltage in my bios is confusing me, i may be an idiot. its set at default but when i try to change it, it doesnt give me an option of actual voltage, just like stepping or something....+.025, +.050..etc...or vice versa. Any ideas???

[Johnathan424]

I am running ....

XP2100 @ 2303MHZ (FSB 177x13)
Vcore 1.65 !
MSI K7N2 Mobo
Samsung 3200 DDR400 512meg 5-2-2-2
(This can not be pushed at all it's at the max for 1.65 Vcore for mine anyway. I pushed her up too 185FSB ay 1.675Vcore)

[TheNewbie]

1.68 stock Athlon XP 2400+ running at 2800+

[TranceBear]

I plan to power a small city with the power this poor CPU is taking. 2.6v

DO NOT TRY THIS AT HOME!!

[TheNewbie]

what kind of cooling do u have to hold that kind of V.?

[TranceBear]

Originally posted by TheNewbie
what kind of cooling do u have to hold that kind of V.?


It does not run all day at that voltage, That is my MAX. I am the air-cooled guy your parents warn you about. I am a avid follower of the Hoot school of air-cooling. I have a very trick Zalman/Radio Shack/GM Auto part/ghetto cooling system that works well and quiet, never above 40c even playing videos or benchmarking. Pictures to come soon.

[TheNewbie]

Hmm picture ehh i don't know if i would look or turn away it sounds pretty rough

[verbatim]

Hey newbie how u manage to get 2.3 ghz? I got the same chip and can only get 2.2! can u post more specs 4 me like bios settings etc? U live in Texas huh, hot there like it is here everyone else's ambiant was alot lower than mine till u came along, makes's me feel better now :)

[TheNewbie]

I can get it up to 2.4 not stable tho. Email me the /'s u want to know about my system to:Accordguy79078@wmconnect.com

[verbatim]

Hey trance bear, isnt the stock mhz for a xp3000 still only around 2.3/2.3mhz? that is a great o/c congrats!

[TheNewbie]

I'll be right back k going to get pics of my bios for u

[verbatim]

sweet

[grndbef]

2100 "b" 0302 @ 2184 .. 13x168 .....my memory is 400 but runs better @ 166-169 fsb higher scores on sandra and doesnt fail mem test like it sometimes does @200fsb....I couldn't keep the computer stable @ 200 fsb would reboot by itself...using a nice copper heatsink air cooling with Asus A7N8X two matched mem sticks

[nezos]

2000+palomino(agoia0220)@2004mhz vcore 1.977 on gigabyte 7va

[Chaos Snake]

Still running at 1.6 on a 2100 t-bred b. waiting to get water cooled to realy push it.

[cV]

running 1.75vcore on the AUIGA/8KHA+ system, will do 1800MHz at that, can do 2GHz at 1.95v.

My JUIHB/8RDA+ will do 2.6GHz at 2.15vcore with 26C core temp (winter air at full blast) but of course I don't keep it there. 2v @ 2.3 and 2.15v @ 2.4 now with MCX462+ air cooling.

The old AGOGA XP 1800+ when alive would do 1725MHz at 1.85v.... 1.66GHz at stock. I'm pretty sure it would've hit 1.9ish at 2v and 2GHz at 2.2v. That was before I vmodded the 8KHA+.

And the 1300 tualatin celly can do 1.57 at 1.68v. Time for VID vmod...

[cV]

Originally posted by TranceBear



It does not run all day at that voltage, That is my MAX. I am the air-cooled guy your parents warn you about. I am a avid follower of the Hoot school of air-cooling. I have a very trick Zalman/Radio Shack/GM Auto part/ghetto cooling system that works well and quiet, never above 40c even playing videos or benchmarking. Pictures to come soon.

:eek: :eek: :eek: 2.6v into a barton? I'm afraid of putting that into my K6-2! :p

Seriously, how do you manage that with quiet air cooling? And how do you manage 3.2GHz at ANY voltage with air cooling? I have to see this.

367W heat output. Don't tell me you have a heatercore clamped to your CPU. :p



I also thought 2.17v was the sky-high limit for bartons and tbreds, beyond that there would be no gain.

Guess I was wrong. Tell us more about this! :cool:

[PalominoBURN]

2.O Vcore thanks to www.dangerden.com H20 cooling :mad: :mad: BURN BABY BURN!! hehehehe

[Baxevan]

I run my Duron in my freshly volt modded ak32 on 2.3V @ 1268Mhz. I'll try 1300 or more in a couple of minutes...

[tempest993]

My 1700+ (new "b" with 1.5v default) @ 1.6v is at 2.13 (170x12.5) right now and will go much higher as soon as I unlock it. I can actually get most of the way into windows at 1.5v.

[dropadrop]

xp1700+ dlt3c jiuhb, msi k7d

1.53ghz (stock) 1.06v
1.8ghz (xp2200) 1.225v
2.267ghz 1.55v

Need better cooling to go higher

[Chaos Snake]

Still 1.6 here. If i could just get rid of that pesky heat.

[altec]

currently have my DLT3C at stock voltage, so it's 1.5v @ 2Ghz :clap:

[PalominoBURN]

New CPU core.. 1.95V 1.7GHZ@2.5GHZ :burn:

OH YEAH.. got my palomino on my soyo KT333 about be running out of a shoebox. HEHE I am gonna set it up for folding and let it run FOREVER! FOREVER! FOREVER! hehe.:mad: :mad:

[SnComet2]

1.6 volt on a tbred 2100 0301 @ 9.5x200 (1.9 ghz) rock solid stable
33 idle temps
would push higher. but 14826 3dmark01 is enough for me at the moment and I like to have cool temps, heh

oh the ram is awesome, its kingston hyperx pc3000, hit 200 mhz with 2-2-2-5 on stock voltage completely stable

[935_MobyDick]

0301 2100+

CPU: 1.825
AGP: 1.8
RAM: 2.7

[a c i d.f l y]

See sig..

[INFERNO2]

XP2000+ runing stable@11x170MHz at 1.8+2.3% voltage:)
48CPU/37CASE under load.
Volcano 9 FAN on SpireFalconII heatsynk.

[Pepsi274]

i have no idea on my voltage on my mobo i do know that i have an amd thunderbird 1.0 ghz im new to this overclocking so im afraid to overclock my cpu i dont have a lot of money to replace my comp lol and my wife might get mad at me lol

[SiGmA_X]

Check your Voltage via your BIOS Health Screen or some app like MBM5 (MotherBoard Monitor 5)...

Mine is at 1.75v right now (No OC, 1.533GHz) but is normally at 1.85v for whatever I need. When I was nForce2'ing it, I was using 2.05v (non-modded) to hit 1.9GHz :)

[Damian]

1.725v at 2030, nice and cool. It could probably run at 1.5v, but I won't bother un-vmodding my socket.

[Nero]

I haven't had a chance to unlock my 2100+ since I just got my new ram, but I can run @ 2158 (166x13) at stock voltages. I can go as high as 2366 (182x13) on 1.85v (ram @ 2.5v still), but my best 3Dmark scores are @ 2275 (175x13) at 1.75v. This is a good thing, because summer is comming, and the less heat the better!

[whatdapho84]

read the specs! =)

[Ununquadium114]

1.8 @ the moment

[JasonBr]

1.8 for burn in , then ill go from there ;)

[Modmonger]

I got my AMD 2100+ at 1.80V

[*Negative*]

I'm running my Tbred 1700+ at 1.5 vcore (undervolt from 1.6) while overclocked to 12.5*133, and it runs nice and stable (cool too).

[INFERNO2]

Originally posted by *Negative*
I'm running my Tbred 1700+ at 1.5 vcore (undervolt from 1.6) while overclocked to 12.5*133, and it runs nice and stable (cool too).

hawe you done some heavy burnins before or what?

[*Negative*]

Not really. I have had it run about 48 hrs of prime95 at the speed in my sig, but have not pushed it much more than that.

My board can't do multi's over 12.5, and my ram (or the chipset, not sure) is very picky so I have it at default right now, and for some strange reason I started wondering if it would run with a lower voltage if I can't overclock it as much right now, so since my board only allows +/-1 from default voltage, I tried it and it runs maybe a degree or two cooler on average.

I just think it's cool that I can undervolt this chip and then overclock it 200mhz. The hightest overclock i've gotten stable is in my sig, but I feel the chip has a lot more room than that.

[Rudski]

AMD 2100+ @ 2600+ 0.025added volts (1.6V)
or 1.73 @ 2.153

[four4875]

im ruinning my current only system at 3.58Vcore its a P1 200 MMX at 291 mhz.

my AMD i had running (died :'( ) was doin 133*17, stock V
its a 2100 Tbred B

[Gautam]

1.95v
See sig

[modenaf1]

Originally posted by four4875
im ruinning my current only system at 3.58Vcore its a P1 200 MMX at 291 mhz.

my AMD i had running (died :'( ) was doin 133*17, stock V
its a 2100 Tbred B


3.58 ?!?!?!?!?!?!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

HOLY S***!!!!!!!!!!!!!!!!!!!!!!!!!!

btw, at that vcore you might actually be "ruinning" it :D

[Cheesy Peas]

below 1.75....
running juihb 1700 dlt3c at 2.05 at stock 1.5v.

will up voltage and speed when i invest in some proper cooling. (stupid volcano 7= :mad:

[modenaf1]

try a duct. I have a volcano 9 which is the crappy hs but the good fan and my pali @ 1.8v runs 46° load at half fan speed too. like 3000 rpm

[DiscoMan40]

1.8 here

[Infinite Enigma]

Seems best I can get with my Volcano 9 is 2.2 ghz @ 1.85. I tried 2.3 @ 1.9, unstable, and did'nt want to juice it more. I assume I could get around 2.24 without the need for more voltage , but I just keep it 2.2 even . Haven't tried any better cooling solutions. I have a JIUCB 0242 revision chip.

[JiMk]

My Xp 2400+ stable at 12x200 with 1.9 voltage...... 24/7 folding home.

[David]

Two DUT3C Tbred Bs here at 1.4V a piece.

[modenaf1]

I just got my pali down to 1.65. ill see if i can go any farther.

[Lyser]

XP1600@1.71Ghz; vcore 1.78; fsb 1.71;
A7V333
CPUtemp 11-14C above ambient (home made Owen Stevens water system)

[czaki]

My JUIHB TBred B 1700+ runs at 2023MHz with 1.675V Vcore. And it's stable. :)

[Audioaficionado]

XP1700+ JUHIB DLT3C 0310 XPMW
Abit NF7-S v2.0
Vantek VA4-C7040 air cooler

Stable @ 200/2000/1.5v multitasking and running FAH3 24/7

[SunRedRX7]

TbredA XP1700 AIUGA 166x11 = 1826mhz
On 1.65V(set to 1.60 in BIOS but I was told aggressive setting on A7N8X adds addition .05V, and asus probe shows close to 1.65)
Temps According to Thermal Probe next to die idle/load = 33C/48C
room temp = 21C

My brothers XP1700 PC is doing 10x166 on 1.55volts(same aggresive CPU setting) I won't overclock his PC as much as I prefer not to do house calls.

[Eroc]

Running at 1.85V for my rig in my sig :cool:
full load...stays around 55C unless. on a warm day sometimes near 60C.

[ayoung]

Im at 1800mhz with my 1700+ @ 1.775

[Bman1238]

i'm at 1800MHz with an athlon XP 1900+ @ 1.85vcore

[Dragonprince]

XP 2400 OC'd to XP 2700 ( 166 x 13.5 = 2.171Ghz) speed @ 1.74 volt :cool:

[breadman]

43C full load at 1.8v. I know I can get into windows at 2400 but vcore has to be 1.85 so why risk it for only 60 more MHz.

Unless someone can convince me otherwise ;)

[Audioaficionado]

As far as I'm concerned, it doesn't count unless you run apps and are able to run stress tests over 24 hrs without any crashes or lockups. Just being able to boot into the OS isn't really considered stable because the system isn't really stressed just running the OS.

[breadman]

Originally posted by Audioaficionado
As far as I'm concerned, it doesn't count unless you run apps and are able to run stress tests over 24 hrs without any crashes or lockups. Just being able to boot into the OS isn't really considered stable because the system isn't really stressed just running the OS.

That's the way I see it too. I've been at 2342 for close to a week now and its run prime for 24+ hours no errors, and run DC apps without crashing. Just a matter of time before I push it some more, mostly waiting for finals to be over with :mad:

[False Christian]

2400+ (2.0GHz) running at 12.5x200 (2.5GHz) using 2.15 volts. Everything is stable thanks to my little 5200 BTU air-conditioner which sits directly beside my open case. Temps are -8 C for the mobo and 20 C for the CPU.:drool:

[Audioaficionado]

So you're telling us that your AC is blowing below freezing air into your case and you're not having frost or condensation problems?

Methinks your temp sensing diode is off by more than a few degrees :p

I glad it's staying cool enough for you

[INFERNO2]

Originally posted by False Christian
2400+ (2.0GHz) running at 12.5x200 (2.5GHz) using 2.15 volts. Everything is stable thanks to my little 5200 BTU air-conditioner which sits directly beside my open case. Temps are -8 C for the mobo and 20 C for the CPU.:drool:

U better attach a photo, so we could all see it..
condenzation is a big problem.. how did you solve it?:rolleyes:

[xcelerator]

2100+ @ (203x11) 2.23ghz w/ 1.85vcore 29c-36c aircooled slk800 w/ vantec tornado 80mm

[OLMI]

mine WAS 2100+ @13x166, 1.75vcore, but i didnt want to overclock my pci and agp. so i'm back at stock waiting for nf7-s

[tweaker]

DUDES! 1.875 volt on a stock A7N8X DLX mobo we got our AMD 2500+ barton stock 1833 and got it to 2400 w/ 12.0 mult. on that board. It is water cooled but what will we get when we put the 226 w pelt with our maze2 copper water block in place????
Stay tuned we will let yall know soon. Me and my best bud built this and are still working on all the fine tuning of this machine!

[False Christian]

I'm running my ATHLON XP 2400+ (2GHz) at 2.5GHz (12.5x200) using 2.025 volts and am burning it in again with Prime95 so I can get to 2.6GHz. I will succeed as I could only do 2.3GHz (11.5x200) until I started buring the CPU in with Prime95 for 24-48 hours, know what I'm sayin'?:drool:

[FishDog3]

I had an xp1800 a while ago and killed it, than ran on a duron 900 for about a month, and just snatched an xp1700 for $35 and hooooboy it begs to ge overclocked. T-Bread core, right now running at 1.6v, 166fsbx12.5 (2075mhz).

Other specs:
a7v8x
Miillinium 2 heatsink with an 80mm adapted on it. Runs around 37c idle, 45-48 with toast running at high priority, takes about 30 min to get it up to 48, gets up to 45 pretty quick. I also brought the voltage up to 1.8 and ran full load and it stayed under 54c, so I think this chip will go a lot farther when I, one, get an slk-800, and 120mm fan, and two, enlarge my cpu duct hole and duct right to the 120mm fan.

May even just go to water, either way I'm happy :)

[Eroc]

New proc in sig. running a 1.75Vcore :D

[Audioaficionado]

Originally posted by FishDog3
...and just snatched an xp1700 for $35 and hooooboy it begs to ge overclocked. T-Bread core, right now running at 1.6v, 166fsbx12.5 (2075mhz)...

Yeah even the ordinary ones hit 2Ghz on second tier air. I was getting 200/2200 @ 1.65v on air until my CPU fan kept crapping out on me. It eventually wounded my CPU so it can't get past 180/2000 even @ 1.65v.

And mine was an average overclocker. The great ones are stable at over 2400 to 2500+.

Edit: my CPU is fine. It's the Abit NF7-S v2.0 newest BIOS v1.4 that's holding me back as I lost <11x multipliers and some stability.

2nd edit: I've enabled 'CPU interface' in the bios and got my multipliers back.

Now I'm at 200/2100/1.6v/53c FAH3 running 24/7

[FishDog3]

Yeah, I am sure I could run at 200fsb, but I have pc2100 memory that is holding me to 166, and I have gotten up to 2.3ghz on 1.6v/166fsb but it was unstable, I'll up the voltage as soon as I cut a biger hole in the side of my case to match the 80mm HSF.

[INFERNO2]

Looks like 2200MHz is the magical lmit for my 2000+ AIUGA, and it runs only at 2.2V at that speed, wc of course...

anyone else clocked xp2000+ tbred?

[Andy71600]

2400+ at 12.5 x 184 for 2300 mhz :)

1.8 Vcore

[INFERNO2]

Originally posted by Andy71600
2400+ at 12.5 x 184 for 2300 mhz :)

1.8 Vcore


Can You give some more details, is this stable for hours of burnin, UT2003 and similar?!

my is stable at 11.5x200@2300Mhz but only up to 35°C (water cooled), that means 1 max hour of burnin then it resets it selfe, its AIUGA, what's yours?

[modenaf1]

I am at 1.7 vcore.

[modenaf1]

I am at 1.7 vcore.

[tfr2087]

im at 1.775 with a athlon 1700 at 2.3 just to be safe:D , and my ram is at 2.9

[OC-Master]

I'm running 2.00Vcore with my 1000C overclocked to 1467MHz! On air and my temps rarely exceed 50c.


OC-Master

[Holst]

Im running 1.9v 2.7gig for day to day usage.

Then 2.075v 3gig for benchmarks and showing off :P

This is cooled with a promethia on a barton 3200

more info on my 3 gig barton here.
http://www.aoaforums.com/forum/showthread.php?s=&threadid=18202

[Norrko]

If you got a Vapochill case you could almost throw any voltage at the CPU.. Burn baby, burn..

/Norrko

[Furious]

Barton 2500+ at 2.2 (11X200) at 1.7v.

[JasonBr]

Barton 2800
212x11.5 @ 1.98v (Modded)

[Grease Monkey]

1.5volts here :D...athlon 1700 JUIHB

[Rokk1972]

running 2800 barton @ 2.42 Ghz on 1.80volts (13x186) load temps between 34 - 38 C (depending on room temp)

[modenaf1]

1.725vcore

[Mustanley]

edit: Down from 1.75 to 1.70 Vcore
2.8 Vdimm
200x11.5

[krial]

1.6v - I don't see any option to adjust the voltage in the bios, or I would have raised it a bit ~

Athlon 2200+ @ 2023mhz (150mhz x 13.5)
ASRock K7S8X Motherboard
512mb Corsair PC2100 DDR
GeForce 4 MX 440, 64mb 4xAGP
Lite-On 48x24x48x16 CDRW/DVD Combo
Thermaltek TR2, copper based vairable speed CPU fan
Slot exhaust fan, 2x 80mm case fans

[Jeff Bolton]

1.725 volts

barton 2500+ (11x200) at 2200mhz

[PoX Freak]

1.65 volts and rock stable @ 2000Mhz (166x12):D

I've run it up to 2512 with 1.85 (although the board supports up to 2.0 volts), but whats the point in frying a perfectly good JIGUB? System specs listed below.:p

UPDATE: New specs listed below are true, as system specs change quite often. Most recent overclock was to the xp2800 range, but due to high initial temps (computer room faces the sun 3/4 of the day), i have recently found that 200x9.0 (1800Mhz) is a safe, stable, yet still usable speed. BTW, volts also dropped to 1.55 and still stable.

[NoKtEm]

1.75 here =( nf7-s won't let me go above

[Twista]

http://pics.apartment808.com/users/s4rge/twista.JPG

Ram only 2100 and psu is only 300watt and hard drive only 5400rpm slow so more overclock "WONT" show.

[bill]

Barton 2500+@2.4ghz=2.1v on Water.

[Metallistar]

1.5 on my 1700+ Tbred b @ 2ghz

[grndbef]

2500@2400 1.775v watercooling iceberg with a maze4 block

[Quest For Speed]

For normal use I run my 2500 Barton 2.53@1.95v. For benching I will crank it up to 2.1V to keep my 2615 OC stable.

[Cyrix_2k]

My FSB is 133mhz
But my multiplyer is 11
everything else is listed below

[TROIDX]

I KEEP 1.775Vc ON MY 2500 BARTON @2266MHz

[Jarhead7236]

1.825 on my 1700+, running 205x12...shooting for 210x12....

[joelb79]

AXDA2400DKV3C
AIUHB 0302MPMW

1.6Volts :-)
2.2Ghz :-)
36c :-)
200FSB :-)

Im happy...

[crunkedup]

how do i find out how many volts? im a newb

[Maxvla]

you can find this out by going to your bios and looking for the "pc health report (or status)"

or you can use Motherboard monitor 5 to read your voltages.

Motherboard Monitor 5 Link (http://mbm.livewiredev.com/)