Water cooling pics soon to come........

[rUfUnKy]

I've been letting my WC set up run out of my rig for a couple days now (after waiting on my replacement pump) and I'm now on my way to pepboys to pic up some Water Wetter.I should have pics tonight or tomorow (well web cam pics) Stay tuned ;)

Tipical WC setup:

89 camaro HeaterCore
2 homemade srouds
2 delta 120 mm fans (80cmf) controlled by Fanbus Rheostat BayBus (http://forum.oc-forums.com/vb/showthread.php?threadid=116146)
Swiftech MCW462-UH
Via Aqua 1300

[Diggrr]

So, you just stopped in to tease us until then?
That's kinda cold, man. :D :D

[rUfUnKy]

Originally posted by Diggrr
So, you just stopped in to tease us until then?
That's kinda cold, man. :D :D LOL..Guess I was trying to build a audience ;) ...Step right up and get your tickets here! ;)(Bleeding the system now)

[rUfUnKy]

Two Rheostats One controls the 2 120mm fans on the shroud..The other controls the two exhaust fans and 1 HDD fan.

[rUfUnKy]

Two shrouds with two 120mm fans and a 89 camaro HeaterCore

[grim]

looking good. keep the pics coming.

[rUfUnKy]

Pump relay

[rUfUnKy]

..

[rUfUnKy]

These pics look bad ..ha..o well :) ..That's all ..everything went pretty smooth except the mag pump doesn't seem to like my monitor...

:rolleyes:

[LiGhTBoY]

Hey rUfUnKy , is that a Chenming case ? I have it too but it's prettier.

It's a Koolance ;) :D

[rUfUnKy]

Originally posted by LiGhTBoY
Hey rUfUnKy , is that a Chenming case ? I have it too but it's prettier.

It's a Koolance ;) :D
no, it's a Antec SX1030B

[rUfUnKy]

Oh ya temps ...hehe..25c case 30c CPU ...not bad

[LiGhTBoY]

Originally posted by rUfUnKy

no, it's a Antec SX1030B

It's the same ;)

[Diggrr]

Nice job, bud...good temps too!

[jdmcnudgent]

hey rUfunKy, did you have to dod anything to your case for the core to go in? i ask because i am putting a 89'camaro core in my secondary system, and it seems like a tight fit getting it in there.:p

[rUfUnKy]

Originally posted by jdmcnudgent
hey rUfunKy, did you have to dod anything to your case for the core to go in? i ask because i am putting a 89'camaro core in my secondary system, and it seems like a tight fit getting it in there.:p Thanks,grim..Diggrr..:) Yes, I removed the bottom HDD cage and drilled the rivets out of the top one and replaced them with screws so I could take the Heater Core out with out removing the motherboard...The Core just fits, it actually touches the bottom of the drive cage so if you are working with a small area I would suggest a chevet Heater Core instead (6x6) it will give you a lil more room to play with ..

[jdmcnudgent]

Originally posted by rUfUnKy
Thanks,grim..Diggrr..:) Yes, I removed the bottom HDD cage and drilled the rivets out of the top one and replaced them with screws so I could take the Heater Core out with out removing the motherboard...The Core just fits, it actually touches the bottom of the drive cage so if you are working with a small area I would suggest a chevet Heater Core instead (6x6) it will give you a lil more room to play with .. yes, thanks. but i was wondering if you HAD any special tips. i have the same case as you, well, its a cheiftec, but its the same, and i have already removed the bottom cage as well as cut a 120mm hole in the front of the case for better air flow.:D i dont have the core in yet, but i noticed its a tight fit. my block and fan are coming tomorrow and i will install it then.:)


ps, how much for you to make me 2 of those camaro shrouds???:p

[SemiCycle]

Nice modding rUfUnKy.

[rUfUnKy]

Originally posted by jdmcnudgent
yes, thanks. but i was wondering if you HAD any special tips. i have the same case as you, well, its a cheiftec, but its the same, and i have already removed the bottom cage as well as cut a 120mm hole in the front of the case for better air flow.:D i dont have the core in yet, but i noticed its a tight fit. my block and fan are coming tomorrow and i will install it then.:)


ps, how much for you to make me 2 of those camaro shrouds???:p No tips really , fortunately everything fit nice and went pretty smooth ..like I said you might want to drill out the rivets on the top cage and replace them with screws for easier access..The width of the Heater Core is a snug fit also so you'll have to twist one side in at a time and then slide it in. Just take your time...

about the shroud .. its simple enough make and the satisfaction of a job well done is much more fulfilling than paying someone else to do it... ;) Good Luck

[stereosteve99]

You don't have a radiator right? How did you get all the water in there?

[rUfUnKy]

Originally posted by stereosteve99
You don't have a radiator right? How did you get all the water in there? You mean a reservoir right? I submerged the pump and connected the hose under water then as the air made it's way out I filled it through the T line (bleeder/fill tube).

[stereosteve99]

Yeah it was the reservoir, thanks. Do you fill the system with water before attaching the water block and the rest of the equipment, or did you connect everything and then submerged the pump while it was in the case, then removed it after?

[rUfUnKy]

Yes, I filled the system before I installed it and just added water through the T as needed...

[johnnyw]

That way is quite risky as you do not know wether things are connected appropietly!