will i have any problems with running a 5v fan at 12v

[mark]

I ripped 2 40mm 5v fans with h/s off my 3dfx voodoo 5500 agp, (RIP).
I have connected the fans to my power supply just to see what would happen.
They spin, they spin real fast. They have some decent cfm now. They sound like a dust buster. And I like it.
With me running them at 12v instread of 5v will they burn-out faster or anything?
I'm thinking of running one on my Clock Generator, and one on my North Bridge "greenie" on my Asus p3v4x.
F3ar.
http://www.mjstebbins.com/case.htm
uh huh
mark

[[Oc]acaridans]

if the fans were made to run at 5v, feeding 12v would cause a problem, I doubt anything major would happen but im sure the fans would die quicker

[Super]

Quicker meaning within a few mins, if the fan is good, otherwise, much quicker.

[Shadow ÒÓ]

if the fan is meant to run at 5v and you run it at 12, you also run the risk of heating problems. Not just the motor getting hot but the leads to it........as well as overloading the mobo.

I wouldn't suggest it.

[Luis]

You can connect the two fans in series, that wuould be 6V per fan (still better than 5V)

[Crazy Jayhawk]

You run a pretty high risk of melting the inside of the fans with a stunt like that.

[proze]

running them at 12v will burn them out quicker. check their amperage, and work out the power they'll draw to see if your mobo headers can take it.

otherwise running them in series is a good idea.

[mark]

k the fans are 0.13A @ 5VDC so thats 0.65W each.
I only ran the one fan at 12V for about 15sec, so shush.
I have not used arctic silver adhesive, and would like to know if you guys have any tips.
and have any of you guys superglued a fan onto a h/s? (40-50mm)
any of you guys tinker with the northbrige chips before?
anyone stick a hs/f on the clock generator?

[Paul -The Mad Hatter]

you could also run it @ 7v

[It_The_Cow]

I'm sure many people have implemented active cooling on the northbridges. On some motherboards, cooling it may help to stabalize high FSB speeds

[whiskeyinajar]

just get a 12v fan and forget about this 5v stuff. id hate to see a system go up in smoke just because a little ol 60mm fan. the 5v fan WILL overheat and burn up if ran at 12v for extended periods. an overclocked proc is enough for your system an overclocked fan is just askin for trouble

[mark]

overclocked fan, i think that's a new one.
thanks guys i'll prolly just run them at 5v or 7v. or get a few bucks and get some new fans, i dunno yet

[cjtune]

There could be a chance that your Voodoo fans could be 12V fans being run at 5V in the first place. Most of the small DC fans in the manufacturers' catalogues I've seen are either 12 or 24V. I don't think they'll be making 5V specially for graphic cards. The old 40mm that came with my 486 was 12V.

Normally, if a voltage is excessive, the insulation of a electrical device would break down immediately, causing short circuits and the device would be toast from start, but since your 5V@12V fans seem to be running fine, it's a good chance they are 12V fans.

[mark]

i looked on the back of the fan which shows it is a 5v fan

[cjtune]

It's your call now, mark. Running devices above a rated whatever, if it hasn't died immediately yet, will severely reduce the lifespan. But me thinks it's a 12V fan by built and how cheaply can they make a 5V compared to a 12V? Electromechanical motors depend on voltage for speed so if there's anything they can skimp on it's probably the capacitors or whatever electronic components inside the hub of the fan but most probably not the sleeve bearings as they are very simple components by nature. Go check out a fan manufacturer's website if you have the time.

[M@€$†®Ö™]

I have a bunch of 5v Fans laying around are there any URL for mods to 12v or 7v around ?

Maestro

[cjtune]

Maestro (Jul 27, 2001 04:02 a.m.):
I have a bunch of 5v Fans laying around are there any URL for mods to 12v or 7v around ?

Maestro

Err, don't tell me you plan to mod those tiny PCBs in the hub of the fans... If you just need the extra speed just run them right away at 7V from the PSU power (or 12V, but cross your fingers in case they are REALLY 5V fans).

[mark]

well to run a fan at 5v connect + to the red and - to the black.
to run it at 7v connect + to the yellow and the - to the red
to run it at 12v connect the + to the yellow and - to the black
+ is red on the fan, - is black on the fan.

[*spazzed*]

I ran an electric motor that was rated at 1.5 volts, at 9.6 volts. Poor thing only lasted 30 min :D Give it a shot and see how long it will work, if it worked for aboout 15 sec. without getting hot, try it for abit longer. If you are worrying about blowing your PSU then try using a car battery instead :) (I seem to use a car battery alot :D )

[Kingslayer]

Shouldn't cause anything a good dry chemical fire extinguisher wont fix!

[mark]

hahah kingslayer