Abit KX7-333R / Tbred A :(

Hi.Need help.

i had a XP 1.6+ agoia y but it died... than i got a 1.8+, green, unlocked AIUGA 0249 9.... But i'm stucked I can only use it in default, any slow *** oc causes windows to get errors, or even can get in windows me... i tryed everything, changed opinions and nothing... always used bios b6 modded, vcore 1.75v, vmem 2.85, played with spread spectrum and no efect mobo thing that is rev1.
can't get any fsb higher than 166, but i used 10x/180, windows didn't work right, but prime 95, for half hour that runned, didn't give any error

Need help

Welcome To The Forums!!!!!

.....and to the addiction

Fill this list up(copy & paste not editing my post):

SOFT MENU III

CPU OPERATING SPEED =

- CPU FSB CLOCK =
- RATIO =
- MULTIPLIER FACTOR =
- ENHANCE FOR BENCHMARK =


POWER SUPPLY

- CORE VOLTAGE =
- DDR VOLTAGE =
- CPU FAST COMMAND DECODE =

SPREAD SPECTRUM =
LINEAR SPREAD MO =
LINEAR SPREAD RA =


ADVANCED CHIPSET FEATURES | DRAM CLOCK/DRIVE

CURRENT FSB FREQUENCY =
CURRENT DRAM FREQUENCY =

DRAM CLOCK =
DRAM TIMING SELECT =

- CAS LATENCY TIMING =
- BANK INTERLEAVE =
- PRECHARGE TO ACTIVE (tRP) =
- ACTIVE TO PRECHARGE (tRAS) =
- ACTIVE TO CMD (tRCD)

DRAM BURST LENGTH =
DRAM QUEUE DEPTH =
DQS DRIVE STRENGTH =

DDR DQS INPUT DELAY =
- INPUT DELAY VALUE =

DDR DQS OUTPUT DELAY =
- OUTPUT DELAY VALUE =

MD DRIVE STRENGTH =
- DRIVE VALUE =

DIMM 1 - 4 CMD DRIVE =
- DIMM 1 & 2
- DIMM 3 & 4

DRAM ACCESS =
ENHANCE DRAM PERFORMANCE =
DRAM COMMAND RATE =
WRITE RECOVERY TIME =
DRAM tWTR =
DCLK OUTPUT DELAY =

Now working
SOFT MENU III

CPU OPERATING SPEED = 1830

- CPU FSB CLOCK =166
- RATIO = 5:2:1
- MULTIPLIER FACTOR = 11
- ENHANCE FOR BENCHMARK = disable


POWER SUPPLY

- CORE VOLTAGE = 1.75v
- DDR VOLTAGE = 2.85
- CPU FAST COMMAND DECODE = Normal

SPREAD SPECTRUM = enable (tryed also disable)
LINEAR SPREAD MO = 1
LINEAR SPREAD RA = 1


ADVANCED CHIPSET FEATURES | DRAM CLOCK/DRIVE

CURRENT FSB FREQUENCY = 166
CURRENT DRAM FREQUENCY = 166

DRAM CLOCK = 166
DRAM TIMING SELECT = Manual

- CAS LATENCY TIMING = 2.5 /2
- BANK INTERLEAVE = none / 4blank
- PRECHARGE TO ACTIVE (tRP) = 3 /2
- ACTIVE TO PRECHARGE (tRAS) = 6 /5
- ACTIVE TO CMD (tRCD)= 3 /2

DRAM BURST LENGTH =
DRAM QUEUE DEPTH =
DQS DRIVE STRENGTH =

DDR DQS INPUT DELAY =
- INPUT DELAY VALUE =

DDR DQS OUTPUT DELAY =
- OUTPUT DELAY VALUE =

MD DRIVE STRENGTH =
- DRIVE VALUE =

DIMM 1 - 4 CMD DRIVE = auto
- DIMM 1 & 2
- DIMM 3 & 4

DRAM ACCESS =
ENHANCE DRAM PERFORMANCE = disable /enable
DRAM COMMAND RATE =
WRITE RECOVERY TIME =
DRAM tWTR =
DCLK OUTPUT DELAY = [/B]

Click to expand...

Ram settings didn't affect the system I already used ddr defaults

What happens when you crank the VCore? Go max speed with the V7+ while your at it.

changing the vcore? hmmm...

i can't change the fsb higher than 166.. .can be because the cpu is a tbred a ? must change to b ?

That's up to you to think. I think you need more VCore & more cooling, low on the V7+ just wont cut it for a TBa, but then again I don't know what your ambient temps are & what your load temps are so its up to you to take the risk.

oh.... My temps are idle, cpuidle 26º and full 42º ...

No temps problems my problem is only the fsb....
I used with my "dead" xp, fsb at 200, and i tryed this 8x/200 and no working good ok?

Well when you increase the FSB you increase the CPUs clockspeed, unless your dropping the multiplier, so more VCOre will be needed. What happens when you drop the multiplier then up the FSB?

U don't understand ....

I'm not a new user and i'm used to do oc... I left my old sign to show that Preview overclock ...

I increase the fsb, and drop the multiplier Must be. But i can't use this system in oc... can only use fsb 100/133/166 estable... any slowass oc, windows me, or don't get in, or if get's give errors and more errors.... registry is corrupt is the "common"...