1700+ tbred-b owners post here!!!

[arnoldma]

please post if you got a 1700+ tbre-b with the info below, so every1 who has this / noob overclocker such as me can compare with something:



CPU Stepping: DLT3C JIUHB 0308XPMW

Memory: Corsair xms twinx pc3200 6-2-2-2

Speed of CPU: 200*11.5 / 2300mhz

CPU Voltage: 1.75v

CPU Temp: 52C full load

Board: NF7-S v2.0

Vdimm: unchanged 2.6v

Vdd: unchanged not sure

Notes: need water cooling!!! see sig for my ****ty air cooling!



notes: stable on prime95 and all other benchmark programs. would go higher but i only have air cooling, got up to 210x11.5 stable but temp went up to 60C, so i had to lower as i didnt wanna go above 50C load temp!

thanks alot guys, bye.

[TT600KHatf]

I just tried overclocking yesterday fo rthe first time and mine is stable as hell at stock voltage. I haven't tried to go any higher yet but I will in the next few days. I ran 3Dmark2001 and scored right around 11000. I'm thinking I can get that up a bit when I start messing around in the bios a little more.

[Nolo31]

My mushkin ram hasn't arrived yet, so im using one stick of pc2100 256mb kingston value ram. at stock voltages for everything, i can get 190fsb at 6-3-3-2.5 timings. and run prime95's torture test stable for hours. Can't wait to get my mushkin ram :)

[arnoldma]

can u guys please post it like i have and have ur stats posted with:



CPU Stepping: (inc. week number and letter after, i.e. 03008XPMW)

Memory: (inc. timmings and speed)

Speed of CPU: (overclocked speed, stable 24/7)

CPU Voltage: (core voltage of cpu)

CPU Temp: (temp of cpu)

Board: (brand, model, rev number, etc...)

Vdimm: (ram voltage)

Vdd:

Notes:



thnx, and add anymore if u feel is needed :)

[hitechjb1]

stepping code: Tbred B 1700+ DLT3C JIUHB 0310 XPMW
ram: noname 512MB x 1, PC3500 C2, actual 5-3-2-2
speed: 210 x 12 (2.52 GHz)
v core: 1.875 V
temp: 48 C load, 40 C idle (4700 rpm)
cooling: HSF SK-7, TT SF II, NB default + fan, SB passive
mb: A7N8X-DLX rev 1.04
vdimm: 2.6 V
vdd (chipset): default 1.53 V (measured)

notes:
Other operating points:
2.2 GHz 1.5V, 34 C load, 3000 rpm fan
2.4 GHz 1.65V, 38 C load, 3000 rpm fan

[altec]

Stepping: DLT3C JIUHB 0307
RAM: Kingston HyperX pc3500 2x 256MB: 7-3-3-2
Speed: regular day: 205x12 (2.45Ghz) Highest: 200x12.5 (2.5Ghz)
Vcore:1.85v, 2.5Ghz: 1.9v
Temp: 48C Idle, 54C load, 2.5Ghz: 51C idle 58C load
Notes: SLK800 w/ Delta 68CFM fan
Board: Abit NF7-S Rev. 2 (Best board out there!)
Vdimm:2.8v
Vdd: 1.7v

[Mitko]

Well,i have Epox 8RDA+ C1 ,2x256 DDR 3200 CL2 TwinMoss,and a crapy 1700+,DLT3C 0311 stepping 4

That`s 24/7:
http://www.setcom.bg/dpetrov/2430.jpg

The CPU,the GPU,the northbridge and the HDD are Coolance-watercooled

The CPu can bench at 26500 too,but under 1.85V....well,if considering that it`s default voltage is 1.5V i dont want to damage it..i cant find something like this now:p

[Ben721]

Stepping: JIUCB 0251
RAM: 512MB PC2100 Corsair Value Select
Speed: regular day: 148*12.5 (1.85) Highest: 153x12.5 (1.912)
Vcore:1.75
Temp: 31C Idle, 38C load
Notes: AX-7 w/ Quad Led Fan
Board: Abit KR7A-RAID

[katka]

Stepping: DLT3C JIUHB 0308 XPMW

I can't tell you the other things just yet (I just orderd everything but the RAM and Heatsink and CPU (I got the HS and CPU about a week and a half ago).

I'll have everything in about a week. Can't wait to try my first overclock.

[arnoldma]

guys i've edited my post about what info is needed, thnx to altec for adding a couple more, go back and edit ur post if you want.

thnx alot, bye.

ps. its now in bold and underlined.

[Cheng]

CPU Stepping: 0310 XPMW

Memory: Corsair 3000 @ 200 2-3-3-5

Speed of CPU: 2.3 (200 x 11.5)

CPU Voltage: 1.62

CPU Temp: 41C Idle, 46 Load

Board: Abit NF7-S 2.0, 1.1 Bios

Vdimm: 1.7V


Notes: Can go a lot higher, 2.5 easily, have crappy vol 11 tho...

[Decaf]

CPU Stepping: DLT3C JIUHB 0310 WPMW

Memory: 256mb Corsair xms pc3200 cas 2-3-3-5

Speed of CPU: 200*11 = 2205mhz

CPU Voltage: 1.50 v

CPU Temp: 36C full load

Board: epox 8rda+ v1.1; vantec iceberq & AS3 on NB, passive heatsink on SB and mosfets & voltage regulator; no other mods

Vdimm: 2.5v

Vdd: default

Notes: slk-800 with TT smartfan @2900rpm
p95 stable 24 hours

[altec]

Mine and hitechjb's seem to be doing the best. :p Yay, I have never like a chip more than this 1700. :D




Edit: 7th star! :D

[arnoldma]

i could get mine up to 2.5 easy if it werent for the damn temp limiting me, i rekon on water this 0308 can go up to 2.7 :)

[Wiz4rd]

CPU Stepping: DLT3C JIUHB 0310XPMW

Memory: Corsair xms 2x512 pc3200 6-3-3-2

Speed of CPU: 194*12.5 / 2436mhz

CPU Voltage: 1.75v

CPU Temp: 36C full load

Board: Epox 8rda

Vdimm: unchanged 2.6v

Vdd: 1.5


Notes: Running with slk-800 and 120mm fan pushing 119 cfm of air.

[Cheng]

I can easily get up to 2.5 rock solid (definitely more with better cooling) , just don't want to with this Volcano 11 :)

[OrionRU]

CPU Stepping: DLT3C JIUHB 0310WPMW

Memory: Corsair xms pc3200c2 6-2-2-2

Speed of CPU: 220*10.0 / 220xmhz

CPU Voltage: 1.75v

CPU Temp: 45C full load

Board: NF7-S v2.0

Vdimm: unchanged 2.6v

Vdd: unchanged not sure

Cooling: SLK-900U + TT Smart Fan 2 At full power (+ 3 exhausts +2 intakes).

PSU: Antec TP 430

[Mark620]

Well I seem to be doing the wrong thing...

Speed of CPU : 133*15

All other is stock, I only changed multiplier.

Abit KD7-G

XP1700+ JIUHB:0310XPMW

Thermalright SLK-900U

512M Samsung PC3200 DDR

Vcore =1.5V

[adelphia83]

I know it's a T-bred B thread--- however with the amount of people that have been recieving A's from Newegg, this info might be of some use (hopefully :-)

CPU Stepping: DLT3C AIUGA 0248

Memory: Samsung PC2700 DTM ver

Speed of CPU: 190 x 10 1.9ghz

CPU Voltage: 1.87v

CPU Temp: 43 Idle; 50C full load

Board: Gigabyte GA-7VAXP Ultra

Vdimm: 2.7V

Vdd: not altered

Cooling: Volcano 9+ w/ Coolmod, four 2600rpm case fans (2 intake, 2 exhaust)

PSU: Generic CompUSA 400W

Some food for thought: Never buy a Gigabyte board!

-----

Got a Soltek Nforce2 board w/ 2500+ Barton on the way, hopefully I'll get a chance to post some results in the near future ;-)

[nikhsub1]

stepping code: Tbred B 1700+ DLT3C JIUHB 0310 XPMW
ram: 2x 256 MB Twinmos/Winbond BH-5 5-2-2-2
speed: 210 x 12 (2.52 GHz)
v core: 1.85 V
temp: 32 C load,
cooling: in sig
mb: A7N8X-DLX rev 2
vdimm: 2.6 V
vdd (chipset): default

This is everyday, all day 24/7 folding. Have had the cpu to 2650 for a short while, but it failed P95 after about 10 minutes and my CPU no like voltage over 1.9V.

[rugbyroy]

stepping code: Tbred B 1700+ DLT3C JIUHB 0310 XPMW

ram: 2x 256 no name

speed: 184 X 12.5 = 2.3

v core: 1.55

temp: 34 C idle (haven't stressed it yet)

cooling: slk 800 w/ 60x 15mm fan @ 4000 rpm (no clue what cfm)

mb: NF7-2 V2.0

note: I need a new psu badly, my vcore fluxuates and isn't stable at all. I will probably also get some new ram considering I cannot figure out what kind mine even is...

[Elin27]

CPU Stepping: DLT3C JIUHB 0310XPMW

Memory: OCZ PC3200 512MB EL-DDR 6-3-2-2

Speed of CPU: 214*11.5=2470

CPU Voltage: 1.825v

CPU Temp: 40C FULL LOAD

Board: NF7-S v1.2 Bios 17

Vdimm: 2.6V

Vdd: 1.85V (Pencil Mod)

Cooling: SLK-800(A) with TT SmartFan 2

[arnoldma]

nice one guys, looke like i gotta go a bit mroe from my 2.3ghz, hmmm could and admin please edit this thread so that only posts with the stats of there cpu is left, that way it's easier as a databse or whatever.

thanks alot, bye.

[gazzrawly]

GOOD ADVISE ALDELPHIA :) NEVA BUY A GIGABYTE! God damn thing took me hella hassle overclocking it BUT IM HERE!

CPU Stepping: 0251 DUT3C JIUCB RPMW

Memory: 512MB 1X512 PC2700 WINBOND @ 2,5,2 CAS 2

Speed of CPU: 166X ALL THE TIME Havent tried faster = 1.84ghz

CPU Voltage: Stock 1.5V i believe ;)

CPU Temp: Idle = 31*C Full RPM on Fans/34*C Slow RPM

Board: Gigabyte GA-7VAX, Rev 1.1

Vdimm: Stock

Vdd: None

Notes: NEVER BUY A GIGABYTE ;) WINBOND DDR ROCKS THIS WORLD! Can run it @ PC3200 no prob! Well, untill i flashed my bios today with update F10 :( Auto sets now *cries*

Good luck on all overclocks :)

[adelphia83]

Definately-- SAY NO TO GIGABYTE....

The specs for the board looked great upon first glance. It was new at the time, and did not have any reviews, so I figured what the hell... Soon I realized 130$ down the tube. Had to hard-code the CPU to a 166mhz fsb default, just in order to make it past 165fsb. Now under a heavy overclock, the system will not restart, unless it is powered down completely.

I would have saved myself hours of frustration if I would have just purchased the 8RDA, or similar. I put together a system for a friend with a Soltek Nforce2, and was so impressed that I bought one for myself.

[Gautam]

stepping code: Tbred B 1700+ DLT3C JIUHB 0310 UPMW
ram: Hardcorecooling PC3200 CAS 2 (6-3-3-2)
speed: 220.5 x 11.5=2535mhz
VCore: 1.95v
Temp: 47.5 C load, 44 C idle; poor airflow right now
Cooling: Watercooled- D-Tek TC-4, Heatercore, Maxijet 1200
mb: Abit NF7 rev 2.9
vdimm: 2.8 V
vdd: Chipset default (1.5v)

[Severian]

CPU Stepping: 1700+ 0308 DLT3C XPMW

Memory: 6-3-3-2 PC2100 cheapo RAM

Speed of CPU: 2325 MHz

CPU Voltage: 1.725V

CPU Temp: 42C Idle, 50C Load

Board: Gigabyte GA-7VAX 1.2

Vdimm: 2.6

[Kunaak]

CPU Stepping: DLT3C JIUHB 0308XPMW

Memory: Kingston HyperX DDR 3500

Speed of CPU: 201x15=3.006 ghz so far max.

CPU Voltage: 1.95v

CPU Temp: 12C.

Board: Epox 8RDA-Volt Modded.

Vdimm: 2.77

Vdd: 1.94 (fixed resistor)

Notes: 3 ghz is the highest I have gotten into windows with so far. I can get 201x15 for 3.030 but 2000 Pro doesn't handle it well. if I install Xp pro, it should get that speed just fine.
also it's 100% stable to 2.9 ghz, and I have benchmarked at almost any speed below 2.9 ghz.
but with the CPU still new in my Prometeia, I think if I leave it alone for a few days and allow the CPU to break in, and the artic silver to cure alittle more, it should be stable to alittle more.

[hitechjb1]

Kunaak:

I know this is a thread for collecting data, I hope it is ok to post a question that may be interesting:

Since currently I don't have a low temp cooling system to try, what happened when you tried to increase the Vcore beyond the 1.95V reported, e.g. to around 2.0V or 2.05V or 2.1V?

Did you try more than one Tbred B 1700+ DLT3C, if so, what was the highest clock frequency and the corresponding Vcore you got from the "worst" one you tried?

[Kunaak]

absolutly nothing happens when I use more voltage, it doesn't respond at all, doesn't increase stability or anything else.
so 2 volts is about the max it needs for almost any speed I can do. more voltage doesn't make it any more stable or overclockable.

as for my XP 1700, this is the 3rd one I tried. I used 2 DUT3C's and this one DLt3C.
the DUT's both did about 2.6 ghz max.

[hitechjb1]

Originally posted by Kunaak
...

as for my XP 1700, this is the 3rd one I tried. I used 2 DUT3C's and this one DLt3C.
the DUT's both did about 2.6 ghz max.

Are the two DUT3C Tbred A or Tbred B?

[Kunaak]

the DUT's were both JIUHB's so I guess B's.

[SiliconX]

Originally posted by arnoldma
i could get mine up to 2.5 easy if it werent for the damn temp limiting me, i rekon on water this 0308 can go up to 2.7 :)

Don't count your chickens before they've hatched. I have the same chip you do, and a pretty good watercooling system and 2.4 seems to be the highest she'll do. I since designed the piping arrangement for more cooling and less restriction and i'll post back with results later today or tomorrow

[arnoldma]

Originally posted by SiliconX


Don't count your chickens before they've hatched. I have the same chip you do, and a pretty good watercooling system and 2.4 seems to be the highest she'll do. I since designed the piping arrangement for more cooling and less restriction and i'll post back with results later today or tomorrow

nah u have a RPMW i have a XPMW... so its a lil bit different :D

[SiliconX]

Fixed. I got a new chip and forgot to change my sig lol

[arnoldma]

damn u r stable on 1.7v, mine is 1.75....

[SiliconX]

[b][u]Proc:AthlonXP 1700+ DLT3C JIUHB 0308RPMW
Memory: 2x512GB Corsair XMS3500 2-2-2-5 2.7v(MBM reads as 2.8v though)
Speed: 2500MHz(200x12.5)
Voltage: 1.8v
CPU Temp: 44C idle/49C Load
Board: NF7-S rev2.0
Cooling: Swiftech MCW5000-A/MCP300/dual D-Tek heater cores/1/2" ID Clearflex
Power Supply: PC Power and Cooling Silencer 400