2500+ OC's...please post

[XunknownX]

I've been OCing my 2500+....toying around with it a bit and I just wanted to see where you guys are at. If you have a 2500+ please post whatever you can of the following:

Stepping:

Core Voltage:

FSB:

Multiplier:

Water/Air:

HSF:

Idle/Load temps:

RAM Type:


And yes I could just go check out the cpu database, but I don't exactly trust it. I prefer to hear from actual people.
Mobo Type:

Chipset:

OC Total Mhz:

[Steven4563]

my dads got his 2500+ @ 3200+ stock vcore i dont know the rest as i dont live near him

[Neeseius]

Core Voltage: 1.65

FSB: 200/stock 166

Multiplier: 11/locked

Water/Air: Air

HSF: Arocool

Idle/Load temps: 45C/50C

RAM Type: 1x512 MB Corsair XMS 3500@400MHz

Mobo Type: Asus A7N8X-E

Chipset: Nvidia Nforce2

OC Total Mhz: 2200/stock 1826

[SK8]

aqxea 0328 kv4d
11 x 200 = 2.2ghz stock vcore
W/c rbx - caprice - 1250
31idle, 33c load
8rda+ A1 nb
ocz pc2700 @ 3200 stock volts , timings 2-2-2-11
Enermax 460w

[Dragonprince]

Stepping: Did'nt write it down :/ but its definetly an unlocked core ;)

Core Voltage: 1.75

FSB: 200

Multiplier: 11

Water/Air: Air

HSF: AeroCool Deep Impact 101

Idle/Load temps: 36c / 43c

RAM Type: OC Systems PC3200 @11-3-3-2

Mobo Type: Epxo 8RDA+/FIC AU11

Chipset: nForce2 voltmod to 1.85v VDD so I can run fsb@200

OC Total Mhz: 1.83@2.2Ghz = 370 Mhz above stock.

[9mmCensor]

Stepping: AQXEA

Core Voltage: Stock

FSB: 200

Multiplier: 10.5

HSF: Vantec Areocool

Idle/Load temps: 53C Load (MBM5) - Idle? What's that?

RAM Type: OCZ DDR400 Dual Channel (2x256) Platnium

Mobo: Abit NF7-S rev. 2

OC Total Mhz: 2100Mhz

[marms]

Stepping: not sure, is on 24/7 so can't check

Core Voltage:1.72v

FSB:206

Multiplier:11

Water/Air:air

HSF:coolermaster aero 7+ (speed set for almost silent)

Idle/Load temps:45-50c usually about 60%-90% load (14-16c above system temp)

RAM Type:2*256 crucial pc3200 cas 2.5 (running dual channel)

M/B:Abit nf7s rev2

overclock: 433Mhz

cpu is unlocked oem, bought it about september/october would probably do more but i hadn't really a chance to play about with it as i needed it on as a server and just set it to 11*200 then upped the fsb a bit to 206 when putting in a second hard drive

[crimedog]

in sig
haven't tried 2.5, doubt i will
hhahahah just kiddin

[qbas]

Stepping: Don't remember

Core Voltage: 1.775

FSB: 200

Multiplier: 11

Water/Air: Air

HSF: Glacialtech Silent Igloo 462 II (with the original fan taken off and replaced with an old case fan)

Idle/Load temps: 47/54

RAM Type: TwinMOS PC3200 @11-3-3-2

Mobo Type: Abit NF7-S V 2.0

Chipset: nForce2

OC Total Mhz: 2200Mhz (well at the moment atleast until i get a better HSF so i can increase my voltages and probably get better ram but games work at the moment really great so i don't need to get one yet)

[Sir Barton]

Well, considering the fact my barton now resides on my keychain lol here is what i had.
AQUCA0304RPAW
1.8V
220FSB
11x multi
HHC-001 w/ 80mm SF2
GA7N400pro w/ HARDM3NU
memory is the same stuff in my sig.
44C idle/53C load

my barton was a first run barton that OCed really well. i chipped the core when i tried putting on a V11 HS :( its on my keychain now, but it did serve me quite well.

[seadog]

Stepping: AQZFA 0340 SPMW

Core Voltage: 2.0

FSB: 233

Multiplier: 10.5

Water/Air: Air

HSF: SLK900a/ TTSmartfanII

Idle/Load temps: 41/51

RAM Type: Mushkin pc3500 lvl2 11-3-2-2

Mobo Type: Epox 8RDA3+ rev2.0

Chipset: nForce2

OC Total Mhz: 2.45ghz

[Wicked Klown]

Stepping: AQXEA

Core Voltage: 1.8 to be safe

FSB: 220

Multiplier: 10.5

Water/Air: watercooled

HSF:Whitewater

Idle/Load temps: 36/41

RAM Type: 2x512mb Geil PC3200Ultra

Mobo Type: Chaintech Zenith Ultra 400

Chipset: NForce2 Ultra 400

OC Total Mhz: 2315MHz

[Dermen]

Stepping: AQZFA 0347

Core Voltage: 1.775

FSB: 206

Multiplier: 11

Water/Air: Air

HSF: SP-97 with 92mm H1A panaflo

Idle/Load temps: 35/40

RAM Type: 2x512 Hyper-X PC3000 @ 2-2-2-11

Motherboard: Abit NF7-S V2.0

Chipset: Nforce2

Total Mhz: 2266

[d4rr3n]

stepping: don't know, but i got it a few weeks ago and it's locked

core voltage: 1.9.......more like 1.87-1.89 really though

fsb: 219 (for prime95 stability, i can run 3dmark up to 225 though)

multiplier: 11

water/air: air

HSF: sp-97 + 92mm vantec tornado

Idle/Load temps: 33/38 C

Ram type: mushkin black level 2 pc3200 2x512 2-2-2-11

Motherboard: abit-nf7-s 2.0

chipset: nforce2

total mhz: 2411

[XunknownX]

Thanks for all the info guys. I'll post mine when I'm done OCing.

[Bon3thugz43v3r]

Stepping: AQXEA 0331SPMW

Core Voltage: 1.65 (Stock)

FSB: 200

Multiplier: 10.5

Water/Air: Water

Idle/Load temps: 30/33

RAM Type: 1x512 Corsair XMS PC3200 C2 v1.1 @ 2-2-2-11

Motherboard: Asus A7N8X Rev 1.04

Chipset: Nforce2

Total Mhz: 2100

My motherboard is holding me back:(

[wpmegee]

Stepping: AQXEA 0323

Core Voltage: 1.85V

FSB: 220

Multiplier: 10

Water/Air: Air

HSF: Thermalright SK-7 w/ Smart Fan II

Idle/Load temps: 49c/53c (mbm5 diode)

RAM Type: 1024mb Kingston HyperX PC3000 2-3-3-11 2.9v


Mobo Type: Asus A7N8X rev 2

Chipset: Nforce2 400

OC Total Mhz:

[Silent Buddha]

Stepping: AQXEA 0330

Core Voltage: 1.75

FSB: 182mHz

Multiplier: 12.5

Water/Air: Air

HSF: Zalman CNPS7000A-AlCu

Idle/Load Temps: 20C/30C (MBM5)

RAM Type: Geil Golden Dragon PC3500 Dual Channel 256mbx2 2-3-3-7 @ 2.6V

Mobo Type: Asus A7N8X Deluxe

Chipset: nForce2 Ultra

OC Total mHz: 2275 mHz

RAM definitely holding me back. To go beyond 182mhz I need to set it to CAS 2 and to go beyond 200mhz it needs 2.8V also. I'm not willing to do that. Better tighter timings and lower bus than very lax timings and higher bus. I've reached 230x10 @ 1.7V but ram was at 2.5-4-4-8 @ 2.8V

[Zerileous]

Stepping: didnt write it down

Core Voltage: 1.65 (stock)

FSB: 200

Multiplier: 11 (locked)

Water/Air: Air

HSF: Vantec AeroFlow

Idle/Load temps: 34/37

RAM Type: Mushkin Black Level 1 PC3200

Mobo: NF7-S Rev. 2.0

EDIT: I am not maxxed at all, as you can tell by my voltage i havent touched it yet. I am just in the beginning stages as i just got the system fully up and running with all the software loaded today.

[fartem]

Stepping: havent written it down

Core Voltage: defualt

FSB: 200

Multiplier: 11

Water/Air: Air cooling

HSF: (stock heatsink and fan)

Idle/Load temps: 37/45

RAM Type: Cruicial 3200 512mbs @200mhz

Mobo Type: Soltek Nforce 2

Chipset: sl-nv400-64

OC Total Mhz: 2.2ghz

[Dragonprince]

Originally posted by Silent Buddha
RAM definitely holding me back. To go beyond 182mhz I need to set it to CAS 2 and to go beyond 200mhz it needs 2.8V also. I'm not willing to do that. Better tighter timings and lower bus than very lax timings and higher bus. I've reached 230x10 @ 1.7V but ram was at 2.5-4-4-8 @ 2.8V

Have you tested 11-3-3-2 ? I had a hard time with mine also until I read here in the forums about nForce2 chipsets liking the 11 setting....7-3-3-2 seems to be a second choice after the 11 setting. Also I have discovered that many ram chips run best at 2.5-2.6v even when you OC them...some times the extra volts actually hinders getting a better OC....

[itshondo]

Currently running my 2500 as a 3200, 1.8 vcore, 1.7 chipset, 2.7 mem 200X11 2200 mhtz

This is as far as I could get it-

Stepping: AQXEA0330 VPWM

Core Voltage: 1.9

FSB:217

Multiplier: 10.5

Water/Air: air

HSF:SLK900a/80mm Tornado

Idle/Load temps: 39 / 43

RAM Type: 2 X 512 Mushkin lvl 2 pc3500

for 2268mhtz.

haven't had much more luck than that

[FizzledFiend]

Stepping:AQXEA

Core Voltage:1.85

FSB:200

Multiplier:12.5

Water/Air:water

HSF:only on NB/SB/mofsets

Idle/Load temps:30/36

RAM Type:512X2 Corsair XMS

[Silent Buddha]

Originally posted by Dragonprince


Have you tested 11-3-3-2 ? I had a hard time with mine also until I read here in the forums about nForce2 chipsets liking the 11 setting....7-3-3-2 seems to be a second choice after the 11 setting. Also I have discovered that many ram chips run best at 2.5-2.6v even when you OC them...some times the extra volts actually hinders getting a better OC....

Yeah, I've tried 2-3-3-11. No post. Had to reset CMOS. Everytime a timing won't work, I have to reset CMOS and it ****es me off. And about the vdimm, I think it's well known that Geil ram needs the extra voltage to even run SPD. But I'll try the lower voltage.

EDIT: I tried 2-3-3-11 @ 2.6V and it worked! Too bad that's as far as I can go :(

[mustrum]

Stepping:AQZEA

Core Voltage:1.65 (stock)

FSB:200

Multiplier:11

Water/Air:air (Arctic Cooling Copper silent TC)


Idle/Load temps:40/55+ (Passed 60 allready!)

RAM Type:512X2 Crucial


It's stable and works well but is too hot for me so i just ordered a Thermalright SLK 900-A.
I got too high casetempos too so i got a arctic cooling VGA Silencer for my Radeon to get the heat of the GFXcard outside.
Also adding 2 more casefans.

Since i hit 200x11 stable at stock Vcore i hope to hit 2.4 GHZ with this baby when my components arrive.

Will post my results as soon they arrive.

[AMD4P4SwithFSB]

Stepping 2500+ AQZEA Week 46 of 2003
Vcore 1.85
FSB: 200
Multiplier: Locked at 11
Volcano 11 planning getting a less noisy Thermaltake A1889 Silent Boost Cooling Fan
44C Idle 49C Loaded
Mushkin 184 Pin 1GB(512MBx2) DDR PC-3500 Level II Dual Pack
Epox 8RDA3+ v2.0
Nvidia Nforce 2
2.2Ghz or 3200+

[Cmnore]

Stepping:AQXEA 03 31 UPMW

Core Voltage:1.8

FSB:190

Multiplier:12.5

Water/Air:O2

HSF: Dynatron w/60mm 6kRPM fan

Idle/Load temps:Not sure. 47?

RAM Type:Hyper-X PC3000

Chipset:KT400(not400a) on Gigabyte GA-7VAXP Rev1.2

OC Total Mhz:2375

I need a better PSU and faster ram, but I'm otherwise happy.

[dubtek]

Stepping: AQXCA 0308

Core Voltage:1.825v

FSB:220

Multiplier:10 (unlocked obviously)

Water/Air:air

HSF:Thermalright ALX-800 Smartfan2 w/Artic Silver 5

Idle/Load temps:36c idle and 40c load

RAM Type:Kingston HyperX 3500 ch5 2-2-3-7 2.7v (dual channel)

Mobo Type:Abit NF7-S v2.0

Chipset:Nforce2 Ultra400

OC Total Mhz:2.21ghz

gonna try higher just leary about putting more than 1.9v on my processor I can hit 2.4ghz but I have to put 2.03 vcore...my temps stay low do you guys think its safe? I idle at like 40c and 44c under load at 2.03vcore?