Kingston hypx 2700 @ 183.3 2-2-2-5

T

THE_ODD_ONE

Registered

​

Joined

Apr 4, 2004

• Apr 22, 2004

• #1

Ok this is where im am at the moment. 183.3 fsb 2-2-2-5
have voltage @ 2.7
I have Kingston Hyperx 2700 512 meg stick


want to try for 200 fsb
what timings should i try to set it @
and should i bump the voltage up to 2.8 and see how it does?

needless to say this memory looks to bee some BH5 ( i got it about 10 months ago)

 

galador

Member

​

Joined

Dec 7, 2003

Location

Texas

• Apr 22, 2004

• #2

My Corsair PC2700 XMS does 192 @2,2,2,5. I've read at newegg.com reviews that it can do 200 at 2.5,3,3,7. 183 is not bad at all for a pc2700.

 

S

Speed_Mechanic2

Member

​

Joined

Aug 15, 2003

Location

Ft. Hood, TX

• Apr 22, 2004

• #3

Raising tRCD (RAS-to-CAS Delay) to 3, and probably tRP (RAS Precharge) may allow you to reach higher clock speeds. Raising voltage and/or loosening timings can help raise clock speeds.

 

M

mtlcafan79

Registered

‍

Joined

Apr 7, 2004

Location

Annapolis, MD

• Apr 22, 2004

• #4

All of the KHX3000 that I have had has shown up as PC2700 in CPU-Z if it means anything.

 

galador

Member

​

Joined

Dec 7, 2003

Location

Texas

• Apr 22, 2004

• #5

Oh, I forgot one thing. I got it at 181 @ 2,2,2,5 now because it got too hot for my comfort.

 

R

repo man11

Member

​

Joined

Dec 28, 2001

• Apr 22, 2004

• #6

See my signature. It has run at 214 with the tightest timings.

 

OP

T

THE_ODD_ONE

Registered

​

Joined

Apr 4, 2004

• Apr 22, 2004

• Thread Starter
• #7

I need to put a temp probe on it to watch the temps . I am going to try some more test with the timingd to see if i can hit 200.

I tried 3-3-3-11 and i could not boot to windows but it my have been my 2500 needing more volts .I had it at 1.75 and it would not boot into windows but posted fine. as I type this I am at stock volts on the cpu and it is 38c @ 2014.3 on cpu-z and the fsb is 183.3 running 1:1

I am worried about the pci and agp bus speeds
i want 200 so the agp/pci ratio will be reg.

i am running a a7n8x asus board.

 

OP

T

THE_ODD_ONE

Registered

​

Joined

Apr 4, 2004

• Apr 22, 2004

• Thread Starter
• #8

wow repo that is awsome !!!

 

P

Pieros

Registered

‍

Joined

Oct 8, 2003

Location

Greece

• Apr 23, 2004

• #9

THE_ODD_ONE ur memory looks to have infineon chips
bad luck

 

OP

T

THE_ODD_ONE

Registered

​

Joined

Apr 4, 2004

• Apr 23, 2004

• Thread Starter
• #10

I took off the heat spreader to take a look and sure enough its infineon.

But I still would say that my luck could have been a whole lot worse .

 

disk11

Member

​

Joined

Dec 30, 2003

Location

Charlotte

• Apr 23, 2004

• #11

I also have infineon chips. It did 2-3-2-11 @ 200 in my NF7-S with 2.9BIOS/3actual, but after that it seems to crap out. Prime fails in 10-15 minutes @ 210, same vdimm, and 2.5-3-3-11 timings I wish I had the skills/balls to do the vdimm mod.

My chip batch is supposed to be set to 3-3-3 @ ddr400, so I guess I'm not doing too bad.

 

OP

T

THE_ODD_ONE

Registered

​

Joined

Apr 4, 2004

• Apr 23, 2004

• Thread Starter
• #12

@ 185 FSB 2-2-2-5
I say for $70.00 when i bought my stick I did ok

 

disk11

Member

​

Joined

Dec 30, 2003

Location

Charlotte

• Apr 23, 2004

• #13

am worried about the pci and agp bus speeds
i want 200 so the agp/pci ratio will be reg.

i am running a a7n8x asus board.

Click to expand...

The board auto locks it for you, so run whatever speed you want

If I remember correctly, the nf2 locks the PCI bus @ 33. On my NF7 I can adjust the AGP up to 99.

 

OP

T

THE_ODD_ONE

Registered

​

Joined

Apr 4, 2004

• Apr 23, 2004

• Thread Starter
• #14

Yep it locks it

I just just checked it using the cpuid tool that shows all the goodies .

FSB @ 185 and agp and pci looking good at 33.3 and 66.6

(reboots to set the FSB up a few mhz. )

 

disk11

Member

​

Joined

Dec 30, 2003

Location

Charlotte

• Apr 23, 2004

• #15

Man, the best I can do now is 2.5-3-3-11 I hope I'm not killing the chips. I can't afford new chips right now.