I feel like I'm nearing the halfway point of my seemingly endless project and I wanted to post some pix. Total from scratch
Never-ending Parts list:
2) 24"x48"x.25" Lucite Acrylic slabs from Menards. ~$36.00each
5) Plastic Epoxy ~2.00/each
2) Aquarium Sealant ~2.00/each
1) Dremel w/unlimted cutoff wheels and general purpose sideways bit ~75.00
1) 10sqft under carpet foam - dirt cheap
Misc fittings up the wazoo) - All fittings are true 1/2ID except for waterblock which has 1/2 fittings but 3/8ID and rads with 3/8ID as well. ~20.00
1) Old Bix (ungoldy expensive)
1) New WA2-style rad (thanks!) ~48.00
1) Hydro l30 (cracked housing, numerous incorrect impeller installations -Thanks to the guy who put the pic on how to install the impeller correctly - sealed with plumbers goop and silicone) ~dden $'y
1) Mag 3 - ~48.00
Tubing) Mix of vinyl form menards and clearflex from old project. Used the old cleaflex beacuse it was easier to work with in the insides. May yet spray-paint those lines beacuse they're ugly.) ~10.00
1) Maze4 GPU block
1) RBX
Need all the electronics added yet. Fans are hopefully coming in this week after a *month* on screw-up order... Will post info on all of that when they're installed.
Using the last picture as a reference, the bottom-right compartment will hold a powersupply and fan speed controllers, 3 fans inside the box on the top blowing out, 1 fan inside the box on the left bowing in, 1 fan inside the box on the right blowing out, perhaps 3 fans in the box on the other side of the rads to complete the push pull. Also need to seal up the middle compartment better to reduce the mag3 noise. Need to seal up the Res and stick a drain plug in as well.
Eh, that's about it. I'll followup with more pix hopefully next week after I get some time to work on it this weekend.
Froz
Never-ending Parts list:
2) 24"x48"x.25" Lucite Acrylic slabs from Menards. ~$36.00each
5) Plastic Epoxy ~2.00/each
2) Aquarium Sealant ~2.00/each
1) Dremel w/unlimted cutoff wheels and general purpose sideways bit ~75.00
1) 10sqft under carpet foam - dirt cheap
Misc fittings up the wazoo) - All fittings are true 1/2ID except for waterblock which has 1/2 fittings but 3/8ID and rads with 3/8ID as well. ~20.00
1) Old Bix (ungoldy expensive)
1) New WA2-style rad (thanks!) ~48.00
1) Hydro l30 (cracked housing, numerous incorrect impeller installations -Thanks to the guy who put the pic on how to install the impeller correctly - sealed with plumbers goop and silicone) ~dden $'y
1) Mag 3 - ~48.00
Tubing) Mix of vinyl form menards and clearflex from old project. Used the old cleaflex beacuse it was easier to work with in the insides. May yet spray-paint those lines beacuse they're ugly.) ~10.00
1) Maze4 GPU block
1) RBX
Need all the electronics added yet. Fans are hopefully coming in this week after a *month* on screw-up order... Will post info on all of that when they're installed.
Using the last picture as a reference, the bottom-right compartment will hold a powersupply and fan speed controllers, 3 fans inside the box on the top blowing out, 1 fan inside the box on the left bowing in, 1 fan inside the box on the right blowing out, perhaps 3 fans in the box on the other side of the rads to complete the push pull. Also need to seal up the middle compartment better to reduce the mag3 noise. Need to seal up the Res and stick a drain plug in as well.
Eh, that's about it. I'll followup with more pix hopefully next week after I get some time to work on it this weekend.
Froz