Please Review My BIOS Settings for Tyan Thunder K8S Pro 2882

Hello all i want to start off by saying that i am very comfortable in a normal nforce2 motherboard been doing desktops for a few years but i am very new (first time) to dual processor motherboards and very new (first time) to server motherboards and very new (first time) to an AMD 8000 Chipset. I have set up the server and it seems to run fine. The specs are

1 X Opteron 246 (Maybe ill add a second one later with another Gig of the same ram)
2 Sticks of Corsair
CM72SD512RLP-3200 512MB 64Mx72 184 DIMM 1.2 inches 32Mx8
2 WD 36 Gig Rapters in Raid 1 Using onboard Raid from Silicon
Onboard Rage XL from Ati
DVD Rom from Lite-On
Standard floppy from Sony

Anyways since this is my first time as i have mentioned above i wanted to have the professionals in here take a look and see if i have messed up anywhere before i put this into a working environment.

Advanced


---> CPU Configuration

------> Gart Error Reporting ---> Disabled

------> MTRR Mapping ---> Continuous


---> ACPI Configuration

------> ACPI Aware O/S ---> Yes


---> ACPI Configuration ---> Advanced ACPI Configuration

------> ACPI 2.0 Support ---> No

------> ACPI APIC Support ---> Enabled

------> Multimedia Timer ---> Enabled

------> Bios-->AML ACPI Table ---> Enable

------> Headless Mode ---> Disable

------> ACPI SRAT support ---> Enabled


---> Hyper Transport Configuration

------> CPU1CI-X0 HT Link Speed ---> Auto

------> CPU1CI-X0 HT Link Width ---> Auto


---> Remote Access Configuration

------> Remote Access ---> SMDC
( For remote Access i am never going to actually attach anything special to the server to access it the most will be doing a vpn over a dsl or something similar so im guessing i should disable this)


PCI PnP


---> Plug & Play O/S ---> YES

---> PCI Latency Timer ---> 64

---> PCI Bus Scan Order ---> Descent

---> Allocate IRQ to PCI VGA ---> YES

---> Palette Snooping ---> Disabled

---> PCI IDE BusMaster ---> Disabled



BOOT


---> Boot Settings configuration

------> Quick Boot ---> Disabled

------> Quiet Boot ---> Disabled

------> AddOn ROM Display Mode ---> Force BIOS

------> Interrupt 19 Capture ---> Enabled

------> Wait for 'F1' If Error ---> Enabled

------> Hit 'DEL' Message Display ---> Enabled

------> Interrupt 19 Capture ---> Enabled


---> Boot Device Priority

------> Endless Loop for BBS Booting ---> Enabled



Security


---> Boot Sector Virus Protection ---> Enabled



Chipset


---> Clock Gen. Spread Spectrum ---> Disabled


---> NorthBridge Configuration ---> Memory Configuration

------> Bank Interleaving ---> Auto

------> Node Interleaving ---> Disabled

------> Burst Length ---> 8 Beats

------> Adjust Memory ---> Disabled

------> Memclock Mode ---> Auto

------> DRAM DQS Strob Skew ---> Auto

------> DRAM DQS Strob Skew Value ---> 0


---> NorthBridge Configuration ---> ECC Configuration

------> Master ECC Enabled ---> Enabled

------> DRAM ECC Enabled ---> Enabled

------> DRAM BG Scrub --->Disabled

------> DRAM SCSCRUB Redirect ---> Disabled

------> ECC Chip Kill ---> Enabled

------> L2 Cache BG Scrub ---> Disabled

------> Data Cache BG Scrub ---> Disabled


---> NorthBridge Configuration --->IOMMU Option

------> IOMMU Mode ---> Disabled


---> South Bridge Configuration

------> 2.0 SM Bus Controller ---> Enabled

------> HT LInk 0 P-Comp Mode ---> Auto

------> HT Link 0 N-Comp Mode ---> Auto

------> HT Link 0 RZ-Comp Mode ---> Auto


---> PCI-X Chipset Configuration

------> HT Link 0 P-Comp Mode ---> Auto

------> HT Link 0 N-Comp Mode ---> Auto

------> HT LInk 0 RZ-Comp Mode ---> Auto

------> HT Link 1 P-Comp Mode ---> Auto

------> HT Link 1 N-Comp Mode ---> Auto

------> HT Link 1 RZ-Comp Mode ---> Auto