PDA

View Full Version : Last questions before I order.


inkfx
03-20-05, 12:03 AM
Well when I get home from vacation, which is tomorrow, I would like to start odering my watercooling parts so I can have my comp setup for an upcoming LAN event. I just want some quick feedback on the parts or if I should make any last minute changes. Everything I have is based upon things I have read/seen on this site. I will be buying what you tell me, since yall are the experts. Thanks for all the help so far guys, I'm sure ill be needing it much more in the upcomming week with this on the way. Well here is what I want to order:

CPU Block: DTek White Water
Pump: MCP-650 (I hear it has a little bit of a whime, but im not to worried about noise. I am going for performance)
Tubing: ClearFlex 60 1/2 ID
2x120mm Heatercore with 2x Delta 120x38 @ 152CFM
T-Line x2
Anti-Freeze with UV dye in it

I also want to get a fan controller for those Delta's so any suggestions on one would be good, not to expensive though 30 bucks max for it. I also dont know where I can get caps for the T-Line, I know danger den has some but they are $11 and I dont want to spend that much on a cap seeing as I am going to have 2 T-Lines. Also do you think my power supply can handle this, I will also be doing some OCing, of course. (I have 4 case fans and dual cathodes.) Thanks for any imput, I will check back tomorrow when I get home .

Hey_Its_Cole
03-20-05, 03:41 AM
Well when I get home from vacation, which is tomorrow, I would like to start odering my watercooling parts so I can have my comp setup for an upcoming LAN event. I just want some quick feedback on the parts or if I should make any last minute changes. Everything I have is based upon things I have read/seen on this site. I will be buying what you tell me, since yall are the experts. Thanks for all the help so far guys, I'm sure ill be needing it much more in the upcomming week with this on the way. Well here is what I want to order:

CPU Block: DTek White Water
Pump: MCP-650 (I hear it has a little bit of a whime, but im not to worried about noise. I am going for performance)
Tubing: ClearFlex 60 1/2 ID
2x120mm Heatercore with 2x Delta 120x38 @ 152CFM
T-Line x2
Anti-Freeze with UV dye in it

I also want to get a fan controller for those Delta's so any suggestions on one would be good, not to expensive though 30 bucks max for it. I also dont know where I can get caps for the T-Line, I know danger den has some but they are $11 and I dont want to spend that much on a cap seeing as I am going to have 2 T-Lines. Also do you think my power supply can handle this, I will also be doing some OCing, of course. (I have 4 case fans and dual cathodes.) Thanks for any imput, I will check back tomorrow when I get home .


The two deltas are overkil in my honest opinion. With one of the deltas that you are getting, I get 28-32c idle and 36-39 load and that is at pretty high overclock with a gpu in the loop. I am warning you these fans are loud, real loud. I ordered three casue they where $7 each but i am only useing one.

inkfx
03-20-05, 05:53 PM
So should I just get one and then use the other weaker 120mm that I have? Also what about my powersupply, should it be ok? I am ordering everything tomorrow and I would like to get it all at once. Thanks.

Mr.Guvernment
03-20-05, 07:02 PM
have u considered PrimoFlex tubing? make sure the walls are @ least 1/8 thick (not 1/16th)

i just got my blue PrimoFlex tubing and it is great!

XTTX
03-20-05, 07:04 PM
Will these stains hinder the performance of the tubing/cooling? Just a question.

inkfx
03-20-05, 07:08 PM
Where can I get PrimoFlex tubing?