H2O Cooler Users Here.

[Luie]

Survey:

1) What Brand of water cooling block are you using?
2) What Speed are you using? (eg. 1Ghz @ 1.33Ghz)
3) What Temperature is your CPU? (eg. Idle: 37C, Load: 45C)

[Naeleros]

1) BeCooling Jagged Edge Waterblock

2) 1.4GHz @ 1.65 @ 1.89VCore
(Did have a 1GHz @ 1.566 until I chipped it :( )

3) Don't have a reliable method for testing.

James

[IFMU]

What I did have was a PCMods alluminum waterblock
AMD1.2 @ 1.513
31 - 37 temps

no pelts just water...
but sold it and am now upgrading... so nada at the moment

[TT120]

DangerDen Maze 2-1 waterblock
T-Bird 1400 @ 1545
Idle 27c full load 45c

[SteenkyBastage]

1.2 @ 1.47 w/ 1.85Vcore

cant get any higher till i get a better PSU, running it at 1.47 drops my 5v line to 4.81V.

DD maze2
DD cube radiator
mag7 pump

un-oc'ed load temp can sometimes reach 34C
@ 1.47 load temp can reach 37C

temps based on a probe touching the side of the core itself. however, MBM will report higher temps (up to 5C) unless i have a fan blowing over the waterblock, at which time they usually drop down to close to the probe temp (usually 1 or 2C above probe).

oh, ambient is 25.5C (radiator intake) and 27.2C (case temp).

[Warlord2]

maze2

dd cube radiator

Tbird 1.2@1350 (9x150) vcore regesters as 1.86volts

idle 29c
load 35c

[train22]

Originally posted by Warlord2
maze2

dd cube radiator

Tbird 1.2@1350 (9x150) vcore regesters as 1.86volts

idle 29c
load 35c

volt mod it; up the voltage a bit and I'm sure you'll be able to hit 1.5 with 2.0Vcore. Temps will be around 44C load, which is fine, nothign to be afraid of,

[The Overclocker]

1 becooling copper jagged edge block, when i get is, so i will come back and answer the other two later

[Crappy]

My sig tells the story:cool:

[DoGMaN]

Leufkins waterblock, 4x11x3/4" trasmission cooler, 2x120mm panaflo z-1a 230gph CalPump submersible and Trashcan resevoir.
:D

[fuzzba11]

Argh, I need those temps!!

1.) Dangerden Maze 2 and 1.5 ft bong cooler
2.) 1.4 -> 1.62 @ 1.825
3.) 38 idle, 45 load (wtf?) water temp 24.4 C

[ruquick]

1) Maze 2 w/DD Cube
2) T-Bird 1.2@1.45 (1.85v)
3) 24-39c

[Warlord2]

volt mod it; up the voltage a bit and I'm sure you'll be able to hit 1.5 with 2.0Vcore. Temps will be around 44C load, which is fine, nothign to be afraid of,


I can do 1.6 easy=]

just waiting for my peltier and winter to come first

note

mbm reads vcore as 1.86 but it should only be 1.82

and I dont think I need to do a voltage mod on the shuttle AK31
sense toms said it can go to 2.00 anyways=]

the board was recommended for Duron users sense the vcore can go so high

[.. AE 86 ..]

can you people out there tell me if the water coming out from the waterblock should be cold or warm .. or mayb hot ?
because the water temp. i am getting out from the waterblock is cold... the water temp is just above room temperater (about 35L of water with some anti corrosion stuff)

[Warlord2]

lol well it would be awesome if it was cold but no its supposed to be warm

how warm? I do not know

if its coming out only a few degrees warmer thin when its going in that usualy means your not making good contact with the block and the die

[pauldriver]

Survey:

1) What Brand of water cooling block are you using?

Be Cooling Copper Jagged Edge.

2) What Speed are you using? (eg. 1Ghz @ 1.33Ghz)

1.6a @ 2.66

3) What Temperature is your CPU? (eg. Idle: 37C, Load: 45C)

Idle: 98F/37C , Load: 118F/47C (Seti + Hot CPU Tester Pro 3)

More details

Be Cooling Black ChipBlock
Be Cooling Black GF4 Vidcard Block
Supreme Pond Pump 230GPH model ???? from PetSmart
Hayden Model 401 Transmission cooler 5"x12"x3/4" from Auto Zone, to replace the "copper" one from BeCooling that had aluminium flow restrictors inside. Man I got a bad reaction on that one.
3/8" ID Braided PVC Tubing from Home Base
One 120MM Panaflow intake Fan running at 7v
One 120MM Radio Shack Exaust fan attached to Radiator running at 7v
PSU Fan

pump--->radiator--->chipblock--->vidblock--->cpublock--->pump

It's real quite, except for the whine of the maxtor 7200 RPM drive, unless I turn the fans up :)

[Caffinehog]

HWLabs Blaze (& clip) X2 ( http://becooling.safeshopper.com/6/142.htm?771 )
on a dual 1600+xp@1728mhz, both 40C under load, I don't know idle because I never let it idle. Just one radiator on all that, too!

P.S. I needed to grind the clips a little so they would slide propery. The base could use some lapping, but I didn't bother.

[Caffinehog]

Originally posted by Warlord2
and I dont think I need to do a voltage mod on the shuttle AK31sense toms said it can go to 2.00 anyways=]
the board was recommended for Duron users sense the vcore can go so high
Tom doesn't know what he's talking about. The bios gives options for up to 2.0v, but if you set it above 1.85V, it goes back to the default voltage! This is a known fact... the board was popular, and everyone had this problem.

P.S. Sorry for the thread crap.

[swedkg]

Gemini High flow
1700+ default
39°c @ 20° ambient @ 5v folding
35°c @ 20° ambient @ 7v folding

1466@1650@1.85v 42°c @ 24°ambient @ 7v folding

Dtek rad
Seltz 30

[RnPgrosz]

1) Maze 3, HC w/120mm fans/Eheim 1250
2)XP 1600+@2009 MHz 2.2v
3)Idle 49C On-die, Load 55C On-die

[Nick C]

My home-made block
Eheim 1048
'86 Chevette heatercore

[ElroyCarbon]

P4 1.6a OC'd to 2.5 @ 37C @ idle 44 Load the are rough temps, really not to impressive I suppose.
Danger Den Maze 2 Waterblock/ Copper
E Eheim 1048
Tygon
Running a res :D

[Nico3k]

1) Sig
2) Sig
3) Sig

[juliendogg]

maze 2, ehiem 1250, largish heater core, temps are 38 idle, 44 max load.

1600@1910 with 1.95vcore



AE 86, water temp leaving the block should only be a degree or two warmer than room temp. it should not be hot, the water should be circulating the system much too fast for the water in the block to get "hot".

[chuckerants]

MAze 3
AXP 1600 @ 1.77 GHZ @ 1.8V (so far)
Temps, 30/42 C Load on die.

[Enigma422]

1. Maze 2 P4 (Skt478)
2. Intel P4 NW 2.0GHz @ 2.5GHz @ 1.75V
3. Idle/Load: 39C/44C

My pump is not fast enough :( (144GPH) gonna get a faster, but have other things I have to upgrade first.

[The Spyder]

Maze 3- Amd w/ 86 chevette
Amd Xp 1600@1958
Idle 35/ load 39

[kaltag]

blocks: swiftech
speed: dual xp 1800s (1.533ghz)
temp: idle cpu 1=37 cpu 2=40: load cpu 1=43 cpu 2=45

[BBigJ]

1)Homemade block (in my avatar)
2)1600+ @1796mhz
3)38-40 at full load (depending on the weather)