fluxcapacitor
10-10-01, 02:28 PM
...Okay first lemme say thanks to Steamer (@AMDmb.com's forums) for the webspace. Second, this is not a pro job. The Window was done w/ double stick foam mounting tape and aluminum tape to cover the edges. The case is filthy, its full of dust and finger prints. But I wanted to share with you what exactly I did to it. I used to have a blacklight in it that looked very cool in the dark w/ the blue cables and it made the a7v133 glow a greenish. Anyways, here's the picks:
This is the Delta 80x38 clipped forcefully onto an SK-6 that has held for months now:
http://members.home.net/steamer808/Members/Delta2.jpg
This is my dual Panaflo 47cfm's mounted inside the front 'snap-off' piece:
http://members.home.net/steamer808/Members/Panaflo80sfront2.jpg
This is the filters that cover those two:
http://members.home.net/steamer808/Members/frontfilters2.jpg
This is the fan guards inside the case for those 2:
http://members.home.net/steamer808/Members/Fanguard2.jpg
This is the rear of the case w/ the stock grills cut out:
http://members.home.net/steamer808/Members/PC70reargrills2.jpg
This is the inside of the case panel w/ the window & dual Panny 120's:
http://members.home.net/steamer808/Members/Windowindside2.jpg
This the outside of that:
http://members.home.net/steamer808/Members/Windowremoved2.jpg
Here is that panel on the case:
http://members.home.net/steamer808/Members/caseside2.jpg
And finally here's the case all together:
http://members.home.net/steamer808/Members/case2.jpg
Unfortunately, I don't get the temps I'd like w/ all this. At 70f/20c ambient room temp, I LOAD under 45c. I 'd like to get that under 40. When its like 90f in here, I've hit 48, 49C!!! Currently my right hand is casted due to a broken hand, but I'd like to relap the HS again. I read a good sounding tip to mark the HS w/ an X or some shape that will fill the area of the HS bottom, and not stop lapping until that's gone. I also have two MC462 HS's [1 original & another is rev. 1] so I can re-lap those too if need be, I've lapped all 3 but never been statisfied w/ the finish on them or the results, which have barely been a 1c drop.
This is the Delta 80x38 clipped forcefully onto an SK-6 that has held for months now:
http://members.home.net/steamer808/Members/Delta2.jpg
This is my dual Panaflo 47cfm's mounted inside the front 'snap-off' piece:
http://members.home.net/steamer808/Members/Panaflo80sfront2.jpg
This is the filters that cover those two:
http://members.home.net/steamer808/Members/frontfilters2.jpg
This is the fan guards inside the case for those 2:
http://members.home.net/steamer808/Members/Fanguard2.jpg
This is the rear of the case w/ the stock grills cut out:
http://members.home.net/steamer808/Members/PC70reargrills2.jpg
This is the inside of the case panel w/ the window & dual Panny 120's:
http://members.home.net/steamer808/Members/Windowindside2.jpg
This the outside of that:
http://members.home.net/steamer808/Members/Windowremoved2.jpg
Here is that panel on the case:
http://members.home.net/steamer808/Members/caseside2.jpg
And finally here's the case all together:
http://members.home.net/steamer808/Members/case2.jpg
Unfortunately, I don't get the temps I'd like w/ all this. At 70f/20c ambient room temp, I LOAD under 45c. I 'd like to get that under 40. When its like 90f in here, I've hit 48, 49C!!! Currently my right hand is casted due to a broken hand, but I'd like to relap the HS again. I read a good sounding tip to mark the HS w/ an X or some shape that will fill the area of the HS bottom, and not stop lapping until that's gone. I also have two MC462 HS's [1 original & another is rev. 1] so I can re-lap those too if need be, I've lapped all 3 but never been statisfied w/ the finish on them or the results, which have barely been a 1c drop.