mawsoccer
01-12-07, 07:18 PM
Note: This mod is only effective for dropping your temperatures if you have no HDDs in the HDD bay attached to the fan. If you have three or less HDDs move them to the bay that goes right next to the PSU.
Some aspects are a bit hard to explain but I have attached a couple pictures that will hopefully help explain things a bit.
Required Items:
3 120 MM Fans
4 Pieces of String or Twistie Ties
Steps 3, 4, and 5 require additional 120 mm fans.
Step 1: Remove your HDD bay and flip turn it around.
Step 2: Make sure your fan is still sucking air in from the front, through the HDD bay, and blowing it on your heatsink. Since you flipped the bay around, you might have to reverse the fan direction too.
Step 3: Put a string or twistie tie through the hole of an additional fan to secure it to the hdd bay, it will have to wrap around through the inside of the hdd bay so you can tie it. See pictures below for additional setup help.
Step 4: Use a longer string or twistie tie to attach a 3rd additional fan below the first one. Put the string or twistie tie through the bottom holes of the first fan and through the top holes of the 2nd fan. See pictures below for additional setup help.
Step 5: Lay another fan on top of the HDD bay so that it sucks air from the top of the case down into the HDD bay. See pictures below for additional setup help.
Step 6: Put the drive bay back in so that is directly aligned with you heatsink and the exhaust fan.
Step 7: Hook all the fans up.
When all done, things should look like this:
http://img221.imageshack.us/img221/4070/img1425hy3.th.jpg (http://img221.imageshack.us/my.php?image=img1425hy3.jpg)
http://img221.imageshack.us/img221/2275/img1427mm4.th.jpg (http://img221.imageshack.us/my.php?image=img1427mm4.jpg)
http://img221.imageshack.us/img221/1954/img1429nm7.th.jpg (http://img221.imageshack.us/my.php?image=img1429nm7.jpg)
I have a FN121 Fan blowing directly on my Tuniq Tower. The two TT led fans that came with the case are in the very front and I have a FM121 fan on top of the HDD bay.
As always I really appreciate comments, concerns, and suggestions.
Some aspects are a bit hard to explain but I have attached a couple pictures that will hopefully help explain things a bit.
Required Items:
3 120 MM Fans
4 Pieces of String or Twistie Ties
Steps 3, 4, and 5 require additional 120 mm fans.
Step 1: Remove your HDD bay and flip turn it around.
Step 2: Make sure your fan is still sucking air in from the front, through the HDD bay, and blowing it on your heatsink. Since you flipped the bay around, you might have to reverse the fan direction too.
Step 3: Put a string or twistie tie through the hole of an additional fan to secure it to the hdd bay, it will have to wrap around through the inside of the hdd bay so you can tie it. See pictures below for additional setup help.
Step 4: Use a longer string or twistie tie to attach a 3rd additional fan below the first one. Put the string or twistie tie through the bottom holes of the first fan and through the top holes of the 2nd fan. See pictures below for additional setup help.
Step 5: Lay another fan on top of the HDD bay so that it sucks air from the top of the case down into the HDD bay. See pictures below for additional setup help.
Step 6: Put the drive bay back in so that is directly aligned with you heatsink and the exhaust fan.
Step 7: Hook all the fans up.
When all done, things should look like this:
http://img221.imageshack.us/img221/4070/img1425hy3.th.jpg (http://img221.imageshack.us/my.php?image=img1425hy3.jpg)
http://img221.imageshack.us/img221/2275/img1427mm4.th.jpg (http://img221.imageshack.us/my.php?image=img1427mm4.jpg)
http://img221.imageshack.us/img221/1954/img1429nm7.th.jpg (http://img221.imageshack.us/my.php?image=img1429nm7.jpg)
I have a FN121 Fan blowing directly on my Tuniq Tower. The two TT led fans that came with the case are in the very front and I have a FM121 fan on top of the HDD bay.
As always I really appreciate comments, concerns, and suggestions.