- Joined
- Aug 5, 2002
- Location
- Brisbane, Australia
Yes it's my first time playing with DDR3 platform. Thanks goes out to Asus for supplying the Asus Blitz Extreme and OCZ for supplying the 2GB OCZ PC3-14400 Platinum dual channel kit (Micron DDR3 IC based) and the 1KW OCZ ProXStream power supply
System:
Some super pi runs, all with no copy-waza/maxmem tweaks.
At stock mem speed and stock main timings of 900mhz 8-8-8-27 at 1.9v vdimm
32M
Tighten timings to 7-6-5-18 but still at 900mhz memory frequency.
32M
1M
Prime95 v25.3 Blend Load
Bios settings used:
System:
- Intel Core 2 Extreme X6800 L627A872
- Swiftech G4 Storm/Thermochill 120.3/MCP655
- Asus Blitz Extreme 0601 bios
- 128MB Gainward FX5200 PCI
- 2x1GB OCZ PC3-14400 Platinum - DDR3-1800 rated at 8-8-8-27 at 1.9v
- 500GB Seagate 7200.10 SATA on SATA1 Port
- LiteOn 165H DVD Burner
- Sony FDD
- 1KW OCZ ProXStream
- WinXP Pro SP2
Some super pi runs, all with no copy-waza/maxmem tweaks.
At stock mem speed and stock main timings of 900mhz 8-8-8-27 at 1.9v vdimm
32M
Tighten timings to 7-6-5-18 but still at 900mhz memory frequency.
32M
1M
Prime95 v25.3 Blend Load
Bios settings used:
Extreme Tweaker
AI Overlocking: Manual
CPU Ratio Control: Manual
--- Ratio CMOS Setting: 8
FSB Strap to North Bridge: 266
FSB Frequency: 450
PCIE Frequency: 100
DRAM Frequency: DDR3-1800
DRAM Command Rate: 2T
DRAM Timing Control: Manual
---CAS# Latency: 8 or 7
---RAS# to CAS# Delay: 8 or 6
---RAS# Precharge: 8 or 5
---RAS# Active Time: 27 or 18
---RAS# to RAS# Delay (TRRD): 4
---Row Refresh Cycle Time (TRFC): 48
---Write Recovery Time (TWR): 6
---Write to Read Delay (TWTR): 8
---Read to Precharge Time (TRTP): 8
DRAM Static Read Control: Enabled
DRAM Dynamic Write Control: AUTO
Tramsaction Booster: AUTO/Enabled/Disabled
--- Boost Level:
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
CPU Voltage: 1.48125
CPU Voltage Reference: AUTO
Loadline Calibratiom: Enabled
FSB Termination Voltage: 1.34
North Bridge Voltage: 1.49
North Bridge Reference: AUTO
DRAM Voltage: 1.9v and 2.08v
-DDR3 Channel A Ref Voltage: AUTO
-DDR3 Channel B Ref Voltage: AUTO
-DDR3 Controller Ref Voltage: AUTO
South Bridge Voltage: 1.050
PLL Voltage: 1.50
NB LED Selection: NB Volt
SB LED Selection: PLL Volt
Frequency LED: Turn off
Voltiminder LED: Turn off
CPU Ratio Control: Manual
-- Ratio CMOS Setting: 8
C1E Support: Disabled
Max CPUID Value Limit: Disabled
Vanderpool Technology: Disabled
CPU TM Function: Disabled
Execute Disable Bit: Disabled
PECI: Disabled
USB Configuration
USB Functions: Enabled
Legacy USB Support: Disabled (need to enable it to detect USB flash drives)