800@1066 next?

[Colin Mc Donald]

1066 mhz, temp 34c 1333. fbs
next fbs148,153= no boot...Am I limited to 1066 mhz???

[MilkPowder-2]

Nice OC. :D

But, if you want 140- 150 numbers, you need to go with the P3 Cumine EBs or P3S 1.26 or the new T-Celery 1.0/1.1. They are FSB(not FBS) OC-Friendly. But your Celeron is not for extreme high FSBs. You already have good OC so enjoy and rock n roll man :D

[Godfodda]

Memory may be beginning to hold you back. What are you running? Or voltage. By no boot, do mean no POST or no Windows?

[MilkPowder-2]

hey Godfather he's running a Celermine 800. :D as you would agree, his cannot do 150s+ FSB with it. That would be very unlikely to happen.

[CrystalMethod]

Originally posted by Godfodda
Memory may be beginning to hold you back. What are you running? Or voltage. By no boot, do mean no POST or no Windows?

Probably no nothing. The Aopen bords have a huge gap in between FSB options in the bios, and when you set it by the jumpers. My second system's next FSB optin is 94Mhz, I'm at 83.3Mhz now. Getting 14Mhz more on his FSB probably won't happen without some serious cooling, and raising his Vcore to the point where you seriously run the risk of frying something. Although memory could be holding him back as well, I don't think it's what's holding him back here.

[Yodums]

His cooling is fine and if he has PC 133 ram it should do the job.

What might be the problem is your chip is a cC0 chip and they don't overclock as well as the cD0 and usually the max for cC0 is 1.1 gig so you can be near the limit some what but you can wait for the ram prices to go down again and get it if you want try your luck.

[Godfodda]

Originally posted by CrystalMethod


Probably no nothing. The Aopen bords have a huge gap in between FSB options in the bios, and when you set it by the jumpers. My second system's next FSB optin is 94Mhz, I'm at 83.3Mhz now. Getting 14Mhz more on his FSB probably won't happen without some serious cooling, and raising his Vcore to the point where you seriously run the risk of frying something. Although memory could be holding him back as well, I don't think it's what's holding him back here.

Thanks for the note. I looked in the online manual when I read his other post, but didn't see where it showed FSB options.

[Colin Mc Donald]

merry Xmas.
thank you all for the knowledge shared.
My last post I did not share enough information.
I was not getting a post using any #'s higher than 133mhz. just 1 beep intermittently
my ram is 448/100.
I cleared CMOS and set to 133mhz FSB and all is well.

I think that it is time to hold'em.

I will now move on to beefing up ATI 128 rage 32 meg Video card,
any suggestions or direction will be greatly appreciated.

Novice,
Colin

[Yodums]

Originally posted by Colin Mc Donald
merry Xmas.
thank you all for the knowledge shared.
My last post I did not share enough information.
I was not getting a post using any #'s higher than 133mhz. just 1 beep intermittently
my ram is 448/100.
I cleared CMOS and set to 133mhz FSB and all is well.

I think that it is time to hold'em.

I will now move on to beefing up ATI 128 rage 32 meg Video card,
any suggestions or direction will be greatly appreciated.

Novice,
Colin

I think its defintely your ram as PC100 will not most likely go over speeds of 133fsb.

To overclock your video card you'll need the ATI Tweaker.

Well I don't know much about ATI cards but the best thing you can do now is post in the Video and Sound Section and they'll provide you with the best of knowledge of tweaking ATI cards.

Cheers
TSU