- Joined
- Sep 3, 2008
Hey everyone,
Ok so im not "new" to overclokcing as this is my second system but this is the first time I have been OCing a mobo other than an asus P5N32-E SLI so im trying to get my bearings.
Can people with this mobo post their settings and bold the ones that are most commonly changed??? I did a lot of reading online but its hard to get a grasp with so many people chanign so many things. I have an E8500 im looking to use as well as a QX6850, THANKS!
just fill in this template please
(these are not my settings btw)
MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto
CPU Clock Ratio ...........................: 9
CPU Frequency............................: 3.60GHz
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) .............: 400Mhz
PCI Express Frequency (Mhz) .........:100
C.I.A.2 ..................................:[Disabled]
Advanced Clock Control
CPU Clock Drive...........................: 800mV
PCI Express Clock Drive.................: 900 mV
CPU Clock Skew (ps)....................: 0ps
MCH Clock Skew (ps)....................: 0ps
DRAM Performance Control
Performance Enhance...................: [STANDARD]
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ...............: 2.00B
Memory Frequency (Mhz) ..............: 800*.......800
DRAM Timing Selectable .................: [Manual]
Standard Timing Control
CAS Latency Time........................5*......5
tRCD .........................................5*......5
tRP'...........................................5*......5
tRAS........................................15*......5
Advanced Timing Control - I didn't touch anything in here, everything is set to Auto.
Motherboard Voltage Control
Load-Line Calibration.....................: Enabled
CPU Vcore….……….......1.25000V*...: 1.35
CPU Termination…..... 1.200V*.......: 1.2
CPU PLL…………………....1.500V*.......: 1.5
CPU Reference.……….....0.76V*.......: .76
MCH/ICH MCH Core….1.100V*...........:1.24
MCH Reference….…….0.76V*.............: .76
MCH/DRAM Ref.…......0.900V*...........: Auto
ICH I/O……………….....1.550V..............: Auto
ICH Core…………...……1.100V..............: Auto
DRAM DRAM Voltage …1.800V*............: 1.84
DRAM Termination ..…0.900V*.............: .92
Channel A Reference 0.900V*.............: .92
Channel B Reference 0.900V*.............: .92
Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Disabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Disabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]
Ok so im not "new" to overclokcing as this is my second system but this is the first time I have been OCing a mobo other than an asus P5N32-E SLI so im trying to get my bearings.
Can people with this mobo post their settings and bold the ones that are most commonly changed??? I did a lot of reading online but its hard to get a grasp with so many people chanign so many things. I have an E8500 im looking to use as well as a QX6850, THANKS!
just fill in this template please
(these are not my settings btw)MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto
CPU Clock Ratio ...........................: 9
CPU Frequency............................: 3.60GHz
Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) .............: 400Mhz
PCI Express Frequency (Mhz) .........:100
C.I.A.2 ..................................:[Disabled]
Advanced Clock Control
CPU Clock Drive...........................: 800mV
PCI Express Clock Drive.................: 900 mV
CPU Clock Skew (ps)....................: 0ps
MCH Clock Skew (ps)....................: 0ps
DRAM Performance Control
Performance Enhance...................: [STANDARD]
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ...............: 2.00B
Memory Frequency (Mhz) ..............: 800*.......800
DRAM Timing Selectable .................: [Manual]
Standard Timing Control
CAS Latency Time........................5*......5
tRCD .........................................5*......5
tRP'...........................................5*......5
tRAS........................................15*......5
Advanced Timing Control - I didn't touch anything in here, everything is set to Auto.
Motherboard Voltage Control
Load-Line Calibration.....................: Enabled
CPU Vcore….……….......1.25000V*...: 1.35
CPU Termination…..... 1.200V*.......: 1.2
CPU PLL…………………....1.500V*.......: 1.5
CPU Reference.……….....0.76V*.......: .76
MCH/ICH MCH Core….1.100V*...........:1.24
MCH Reference….…….0.76V*.............: .76
MCH/DRAM Ref.…......0.900V*...........: Auto
ICH I/O……………….....1.550V..............: Auto
ICH Core…………...……1.100V..............: Auto
DRAM DRAM Voltage …1.800V*............: 1.84
DRAM Termination ..…0.900V*.............: .92
Channel A Reference 0.900V*.............: .92
Channel B Reference 0.900V*.............: .92
Advanced Settings
Limit CPUID Max. to 3.....................: [Disabled]
No-Execute Memory Protect............: [Disabled]
CPU Enhanced Halt (C1E)................: [Disabled]
C2/C2E State Support....................: [Disabled]
x C4/C4E State Support..................: [Disabled]
CPU Thermal Monitor 2(TM2) ...........: [Disabled]
CPU EIST Function.........................: [Disabled]
Virtualization Technology................: [Disabled]
