Results 1 to 6 of 6
01-20-12, 11:34 AM #1
Hotrod Heatsink: Faster Fans for the Noctua NH-D14
We are overclockers. We are not satisfied with stock. Like our automotive forebears we hotrod our rigs, pushing them to faster speeds. That?s what we do. And when we do it, our chips get hot and we need to cool them off.
Let's say you really want to overclock your CPU, and you want to cool it with air. You know that the Noctua NH-D14 is a very good heatsink, designed for quiet cooling; but you want more. Can you get better cooling from a D14?
... Return to article to continue reading.
Last edited by mdcomp; 01-20-12 at 11:51 AM.
01-20-12, 11:39 AM #2
"So it is perfectly compatible with the D14 — after you do a little modding (link)."
Doesn't link to anywhere.Dis is mai Pee-Cee;
MB: Gigabyte 990FXA-D3 (rev 1.x)
CPU: Phenom II X4 850 (stock clocks, undervolted @ 1,3v)
CPU Cooler; Box AM2 cooler
RAM: 2x4GB Corsair Vengeance & 1x2GB Corsair XMS3 @ 804mhz 9-9-9-24 1T CR
Graphics card: HD3650 1GB DDR2 (400/400, runs at x4 for some weird reason)
HDD: WesternDigital Caviar Black 1TB, SATA III, 64MB Cache
Case: CoolerMaster Elite 430 (3x 120mm Thermaltake intake fans; 1 front, 1 side, 1 bot. 3x 120mm Thermaltake exhaust fans; 2 top, 1 back)
01-20-12, 03:55 PM #3
Nice writeup. I think the missing link just tells you how to mod it to work with the noctua clips. The clips are made for 140mm hole setup and the other one is setup to attach to 120mm.EVGA x58 Micro (756) / i7 D0 @ 4.0, 1.278v w/HT (Air)
2x 300GB V-rap raid0, WD Caviar Black 640GB & 1TB
HIS 6950 @ 840/1450
Mushkin 6GB @ 6-7-6-18 / Enermax 720 Modular
HAF 922 / Noctua D14Win7 Pro x64 / Mint 10
i7(x58) OC'ing/Info / AMD Oc'ing/Info / C2D/C2Q OC'ing/Info
Recommended Power Supply Listing
01-20-12, 05:35 PM #4
01-20-12, 08:08 PM #5
aHa! Caught! The missing link!!!
OK, here's how you mod it:
Let's start with a normal fan. In this case I have cut the corners out of a Gentle Typhoon. Notice how the clip holder pushes only partly through the flange of the fan:
Now you need The Tool: a 9/32-inch drill bit. You can also use a 7mm drill bit, but that could be a little tight, so you might use an 8mm drill bit. Here is the GT with The Tool:
You grip the drill bit in your hand and slowly drill what is called a countersink hole partway through the flange. I suggest you practice on the intake side of a fan to get the feel of how it is done. If you are too strong or don't know when to quit, you can fully enlarge a hole, and that is not what you want to do.
This is what you want to do:
Note the the enlarged hole -- the countersink -- only goes partway through the flange. The idea is to accommodate the clip holder peg's larger diameter without letting it pull all the way through.
When you are done you will get this:
You do this for all four corners, and you put the clip ends through these pegs. Now your fan will fit onto a Noctua fin stack with Noctua clips.Fan comparison: 65 Fans Tested on a Megahalems
Good Cases for Air Cooling
Core i7 4770K @4.3GHz + HD 4600 w/1GB system RAM | GA-Z87X-UD4H f7
Armageddon w/two NF-A15's | 2x4GB Crucial Ballistix @1600MHz
Samsung 840 Pro 512GB | Seagate Barracuda 7200.12 1TB file disk | WD Red 3TB backup
CM N600 1x GT - AP12 + 1xNF-P12+ULNF front, TY-140 top intake, NF-S12A mid-case, PWM frankenfan side intake
01-23-12, 11:53 AM #6