Page 2 of 3 FirstFirst 1 2 3 LastLast
Results 21 to 40 of 43

Thread: Teac 500 HTPC

  1. #21
    Member
    Join Date
    Jan 2013
    Well the stretch seems to be getting bigger and bigger, first 3", then 4", now just under 5"

    Decided I want the power supply to have its own air supply, wise move I think. Need a right angled main 3 pin psu plug. Hmmmm, thinking I can plug that in the psu which'll be at the front of the case, and dismantle the case feed it out of a cut hole and have a plug hanging out the case like a normal unit would.

    PSU is here, and modular. Where to get short cables from though? My MB cable needs to be all of 4" ideally.
    Sent from my Nokia 5110

    Main rig:
    Processor: Pentium 200mmx 166mhz
    Ram: 64MB
    GPU: 4MB Voodoo 1
    Case: Mini fridge
    Cooling: Above

  2. #22
    Member
    Join Date
    Jan 2013
    Well I don't like the PSU, it's not quiet enough. It's not loud, just not silent at idle.

    Here it is sat in the case. Should have put the drive in to show what I meant about it fouling, just imagine a laptop drive stick out the front an inch.

    Name:  20130222_002.jpg
Views: 279
Size:  140.9 KB

    Floor is going to be stretched 120mm, give enough space to fit the psu on the top left giving it its own air supply.

    The test bed, it runs at least.

    Name:  20130222_006.jpg
Views: 261
Size:  136.7 KB
    Sent from my Nokia 5110

    Main rig:
    Processor: Pentium 200mmx 166mhz
    Ram: 64MB
    GPU: 4MB Voodoo 1
    Case: Mini fridge
    Cooling: Above

  3. #23
    Member
    Join Date
    Jan 2013
    Well more arseache will this project. I should have read more/any reviews on the psu where everyone said idle was too loud. Think i'm going to send it back, it'll just **** me off. Only option is to mod the fan thus loosing the warranty. Plus side is my stretch can go back down to 70mm. Meaning it can actually fit in its unit (forgot to check that bit when adding 5")

    Think of all the extra activities that can be had with this space.

    Think I'll go fanless ATX external and modular. Then get a set of custom cables made up braided up to the case or similar, probably use extenders in the case so I can hide it all underneath. If only I could make up a modular type board to bolt to the case. Hmmm.

    The noctua/thermalright combo is pretty much silent, idling at 28 degrees and 400rpm. It's autoclocked it at 4.2ghz. Not bad for an old Pentium.

    Will be fitting some side usb ports. Disappointed with the board only coming with 6. Considering being real anal and making a box for the sound cards.

    Need to do some research and start playing with the VFDs I have. Mainly trying to get that lcd smartie to work.

    Wow asus just asked me if I'd like to change my bios picture. That's pretty kool. Now, do we go for the Sega, or a Teac logo?
    Sent from my Nokia 5110

    Main rig:
    Processor: Pentium 200mmx 166mhz
    Ram: 64MB
    GPU: 4MB Voodoo 1
    Case: Mini fridge
    Cooling: Above

  4. #24
    Registered
    Join Date
    Jan 2013
    Location
    San Francisco, CA, USA
    Man, I really hope that you pull this one off. I wanted to do the exact same thing a few years ago, but I couldn't get hold of an empty Cyrus enclosure to match my amplifier, even though I was so close to getting one from the manufacturer!

    Subscribed.

  5. #25
    Member m715's Avatar
    Join Date
    Apr 2012
    Location
    Owego, NY
    Heatware Profile
    Cool project, keep up the good work...
    It's neat to see a computer retro fit into something like the Teac.
    DESKTOP: THE MONOLITH - [Project Log]
    | i3-3225 @ 3.3GHz w/Thermaltake CLW0217 Water 2.0 | ASRock Z77 Ext4 | 8GB DDR3 | Sapphire 7950 w/120mm Cooler | 120GB HyperX 3k | Corsair HX750 | Corsair 600T | WIN8 PRO | DELL 24" LCDs x2 | Toshibia 40" LCD |
    LAPTOP: | ASUS X202E | 11.6" TS | i3-3217U @ 1.8GHz | 4GB DDR3 | 256GB SSD | WIN8 |

  6. #26
    Member
    Join Date
    Jan 2013
    Cheers! Glad it has interested someone at least. The cyrus stuff is also very nice. Would make a nice case! They do pop up broken on uk ebay quite often...

    Really like the thermalright cooler though, you get alot of adjustment. I was about to throw my toys out the pram as the gpu suddenly didn't fit. Anyway adjusted everything and there is miles of room. Although I do quite fancy getting a double length thermalright so I can put 2x120mms on there. No one makes one so I'm looking at modding a gpu cooler. Could be a silly idea, but it'll get very hot in there when pushed.
    Last edited by chug; 03-01-13 at 11:01 PM.
    Sent from my Nokia 5110

    Main rig:
    Processor: Pentium 200mmx 166mhz
    Ram: 64MB
    GPU: 4MB Voodoo 1
    Case: Mini fridge
    Cooling: Above

  7. #27
    Member
    Join Date
    Jan 2013
    My fabricator is waiting for me to give them mesh, which turned up today, but I ordered the wrong sort, anyone starting to notice a pattern? Must pay more attention.

    In the mean time, I picked up the remaining Teac AV-H500D which has multi channel analogue inputs for already decoded source, plan being to use the 500i for the front stage, and 500d for the remaining 5.1. Now this little lot came a DVD player, tuner, another cd player and some speakers. Picked up an ebay 1.20 Panasonic surround amp for downstairs, matched with the Mission speakers that came with the Teac setup. Sounds surprisingly good.

    Anyway, now thinking I might as well use the DVD case, it is no different other than it says DVD on the drive and and Dolby/DTS stickers on it. More fitting I think.

    Another bonus is one remote operates both Teac amps meaning they should work well in 7.1. I loose the time delay on the front speakers, but that is a sacrifice worth making for the Stereo peformance.

    Quick comparison on the 500i vs 500d and the 500i wins hand down on Stereo peformance, night and day. The d still sounds good, but not up to par when compared to the i.

    PSU has gone back, hopefully they'll refund me without any agg. Correct mesh has been ordered.
    Sent from my Nokia 5110

    Main rig:
    Processor: Pentium 200mmx 166mhz
    Ram: 64MB
    GPU: 4MB Voodoo 1
    Case: Mini fridge
    Cooling: Above

  8. #28
    Member
    Join Date
    Jan 2013
    Picked up a bargain Auzen hd which'll do for the moment untill an hdav1.3 turns up.

    Left to buy is a gpu, psu and tv card.

    Left to do is wait for my stretch, get the front panel modified with a vfd and get the original power button working.

    Mounting everything should be relatively straight forward now the configuration has been worked out.

    My only stumbling block is the bluray drive. Doesn't seem to be one thread on there to mount to, unless they use m2, which is possible I guess. Think I'll just make a bracket for it to sit in.

    Rob Schneider, he's every-where.
    Sent from my Nokia 5110

    Main rig:
    Processor: Pentium 200mmx 166mhz
    Ram: 64MB
    GPU: 4MB Voodoo 1
    Case: Mini fridge
    Cooling: Above

  9. #29
    Member
    Join Date
    Jan 2013
    Tossers at scan refunded me 20 short on the psu, need to ring them.

    My mate laughed when I threw him my slightly scrunched and scribbled "engineers diagrams" and sighed when I asked him to widen the case a few mm. I was sure those scythe slims were 10mm, not 12mm.

    Typically a second hand hdav1.3 turns up on ebay the day after I buy the Auzen, don't really like the mini jack out idea. Have to replace my cable set as well.

    I had a bid, but it went for a touch more than I wanted to give.

    When I realise it's only the software which offers the bluray decoding right? These are all cards that have come out in 2009 and only offer the hd decoding via supplied software, no one seems to have released anything that'll do both the truehd and dtsma formats, 4 years later...

    Which I guess opens the door to a better card like an essense or something and hopefully someone will release some decent software that'll play blurays in full hd and in the mean time they'll have to be ripped before played.

    Soldered a pc power switch lead to the Teac switch, works. Did the LED, also works but its too bright, and on the actual Teac units they are only on when the units are on standby so I'll just leave that unplugged I think.

    Can anyone recommend me a TV card? Blackgold seems to be popular. Doesn't seem to offer windows 8 support though, might just use 7.
    Sent from my Nokia 5110

    Main rig:
    Processor: Pentium 200mmx 166mhz
    Ram: 64MB
    GPU: 4MB Voodoo 1
    Case: Mini fridge
    Cooling: Above

  10. #30
    Registered C4B's Avatar
    Join Date
    Mar 2013
    As a Hifi-guy I love Teak. Really interesting project.
    Scratchbuilds | CURV3D | Cold Winter |
    Casemods | F4DE |

  11. #31
    Member
    Join Date
    Jan 2013
    Cheers, no progress really yet. Computer is built and in use in another case - a GMC Noblesse. I bought it because I get to say I'm playing with my noblesse, to everyone. The novelty wore off soon enough.

    Just waiting on my fabricator for my case.

    In the mean time, I was looking at my cupboard of bits and built a 500 Tuner mini itx PC to chuck on ebay. Same as that 300 unit, with more space, and I didn't break the front panel. Managed to get the original Teac power button to work, and fit a vfd.

    Attachment 125613

    Attachment 125614
    Attached Images Attached Images    
    Sent from my Nokia 5110

    Main rig:
    Processor: Pentium 200mmx 166mhz
    Ram: 64MB
    GPU: 4MB Voodoo 1
    Case: Mini fridge
    Cooling: Above

  12. #32
    Member
    Join Date
    Jan 2013
    Got an HDAV1.3, seems ok, the Canadian $50 Dac destroyer sounds a touch better I have to admit. Considering sending the digital out from the Asus into a better DAC to get the best SQ in stereo. Sounds a bit better than the Auzen, but that had alot of noise.

    Also been using my setup for films, which consists of a 500i Stereo amp, 500D 5.1 with analogue in, using the fronts on the 500i. Good enough, but after alot of reading 7.1 seems a waste on my setup as there isn't any space behind my seating position. I've only setup 5.1 and its good enough. Not yet come across a 7.1 film.

    Anyway think I'll just use the 500d for films now, 2 volume nobs is a pain to deal with - setting up for every film. All in all very happy. 200's worth of old Teac amp and sound cards sounds 100 times better than a 600 full size apparent 5 star rated Sony HT receiver. Only downside is the lack time delay features, and having to use 2 knobs if you want 7.1.
    Last edited by chug; 09-22-13 at 11:30 AM.
    Sent from my Nokia 5110

    Main rig:
    Processor: Pentium 200mmx 166mhz
    Ram: 64MB
    GPU: 4MB Voodoo 1
    Case: Mini fridge
    Cooling: Above

  13. #33
    Member
    Join Date
    Jan 2013
    Forgot about this, it's nearly done (5 months later) new adjustable floorpan made. New roof pressed, just waiting for the cutouts to be done. Will sort some pics asap.
    Sent from my Nokia 5110

    Main rig:
    Processor: Pentium 200mmx 166mhz
    Ram: 64MB
    GPU: 4MB Voodoo 1
    Case: Mini fridge
    Cooling: Above

  14. #34
    Member
    Join Date
    Jan 2013
    This is a bit more difficult when you're using all the components.

    Got a 7950 for it, been using the lot in a different case. Moved the 3.5" drives to a server, bought a few 2.5" drives for other files.

    Left to do is cut the rear panel out for the I/O sheild, gpu, and sound card, then I can start mounting parts in the case. Fix the mesh/dust filters to the outside, attach the scythe slim fans to either side and give it a paint.

    Name:  20130922_0081.jpg
Views: 137
Size:  216.1 KB

    Name:  20130922_0051.jpg
Views: 137
Size:  176.7 KB
    Sent from my Nokia 5110

    Main rig:
    Processor: Pentium 200mmx 166mhz
    Ram: 64MB
    GPU: 4MB Voodoo 1
    Case: Mini fridge
    Cooling: Above

  15. #35
    Member
    Join Date
    Jan 2013
    Finally got the case back from paint last week, been distracted with fast old cars to winge about it. Had a go at assembling, seemed to go great, except I forgot cables are pretty chunky. Nearly threw in the towel a few times, but I've wedged it all in somehow.

    Had the PSU hole perfect, then when it came to go in no room for cables, so I had to chop it about. Then the board was hitting the mount, trimmed that with my trusty angle grinder, you'd never tell.

    Name:  1.jpg
Views: 81
Size:  161.2 KB

    Got 2.5" drives, 4x 1TB, and an ssd. Mounted them on rubbers and PCI port blanks.


    Name:  2.jpg
Views: 83
Size:  168.8 KB

    Few stand off's and got the sound cards mounted.


    Name:  3.jpg
Views: 75
Size:  235.5 KB

    Then came the false floor.


    Name:  4.jpg
Views: 81
Size:  166.3 KB


    Starting to get tight with the motherboard. It has a GPU cooler as a CPU cooler.

    Name:  5.jpg
Views: 79
Size:  279.6 KB


    Supposed GPU position.

    Name:  6.jpg
Views: 92
Size:  267.1 KB


    Painted outside.

    Name:  7.jpg
Views: 88
Size:  309.2 KB


    Need to clean the masking tape glue from the front, install the buttons, VFD etc, but it is nearly there.

    Name:  8.jpg
Views: 75
Size:  237.2 KB

    Left to do is, work out what room I have left to mount the side fans. Find somewhere to throw the TV card in. One fatal flaw is the Bluray drive hits the board everything, be a shame if I can't get that in.

    Anyway, finished pictures soon hopefully.
    Sent from my Nokia 5110

    Main rig:
    Processor: Pentium 200mmx 166mhz
    Ram: 64MB
    GPU: 4MB Voodoo 1
    Case: Mini fridge
    Cooling: Above

  16. #36

    Member
    bamato's Avatar
    Join Date
    Jun 2013
    Location
    Mesa, Arizona
    Folding Profile Heatware Profile
    This is a really cool project.

    Keep the pics coming.
    Air 540 Liquid Cooled Build Log

    Case: Air 540 CPU: AMD FX-8350 4.6Ghz @ 1.35V Motherboard: Asus M5A99X Evo Videocard: Sapphire Dual-x 7970 (1200C, 1700M) RAM: 16GB Ripjaws/Ares 1866mhz Display: 50" Panasonic Viera Plasma Storage: 250 GB Samsung 840, 1TB WD Black/2TB Hitachi Audio: HT Omega Stryker Cooling: 5x120mm Rads, D5, Heatkiller GPU, EK Supremacy CPU OS: W7 64 bit PSU: Corsair HX750

  17. #37
    Member
    Join Date
    Jan 2013
    Thanks. Have to admit I under estimated how hard it would be to cram it all in there. Not sure the large Noctuas will fit depth wise. Might have to go slim.
    Sent from my Nokia 5110

    Main rig:
    Processor: Pentium 200mmx 166mhz
    Ram: 64MB
    GPU: 4MB Voodoo 1
    Case: Mini fridge
    Cooling: Above

  18. #38
    Folding for Team 32! Ben333's Avatar
    Join Date
    Feb 2007
    Location
    New Hampshire
    Author Profile
    Lovin it man! Keep up the good work. I just recently managed to cram an Athlon 64 3000+ mATX setup into a dead amp's chassis. Nice having an audio PC that blends into my stack of stereo stuff. Looking forward to seeing the finished product!

  19. #39
    Member
    Join Date
    Jan 2013
    Cheers. Get some pictures up?

    Seem to have some issue with the pcie extender ribbon, the gpu doesn't work with one basically. Not sure if both of mine are broken. The card works in the slot normally. Running it with no gpu at the mo. Almost tempted to sack it off, I haven't gamed in ages.

    Fronts on properly, case is on. 25mm thick fans do not fit. I have 2 120mm scythe slims kicking around so will use have to use those on the CPU. Found some 15mm Prolimatech but not even sure I have the extra 3mm to give. Those will exhaust the hot air straight out of the case, and I will have 2 100mm slim scythes to the side of that for intake. Although I'm tempted to just run them off most of the time, normal use doesn't see it get hot at all. Which is why I ended up with the new board.

    The PSU fan is flipped to exhaust the hot air out of the bottom of the case. This will have a 92mm Noctua on the side as an intake.

    On the left hand side the drives are in the way of a fan, so I can only fit 1 100mm scythe to feed air to the GPU (if I fit it) Maybe 2, but the ribbon is in the way.

    Going to bolt the fans to the outter case with m3 bolts, those rubber things don't work on the mesh.
    Sent from my Nokia 5110

    Main rig:
    Processor: Pentium 200mmx 166mhz
    Ram: 64MB
    GPU: 4MB Voodoo 1
    Case: Mini fridge
    Cooling: Above

  20. #40
    Folding for Team 32! Ben333's Avatar
    Join Date
    Feb 2007
    Location
    New Hampshire
    Author Profile
    Quote Originally Posted by chug View Post
    Cheers. Get some pictures up?
    Attatched are the finished front & back. Internal pics: Inside Lid

    Was a quick & dirty build, everything acquired for free A little "ghetto", but silent & sturdy. Other than being my audio player, with the onboard GeForce 6100 graphics it draws N64 games at 1080P
    Attached Images Attached Images    

Page 2 of 3 FirstFirst 1 2 3 LastLast

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •