hey ras, post it here.

jdmcnudgent · 07-12-02, 08:10 PM

post it here in this thread. thanks buddie.

Rasputin'sLiver · 07-13-02, 01:13 PM

sorry man. didn't notice your thread until now, but I think you got it already right?

How's it working out?

jdmcnudgent · 07-13-02, 01:21 PM

Quote:

Originally posted by Rasputin'sLiver
sorry man. didn't notice your thread until now, but I think you got it already right?

How's it working out?

yeah, got it.

i need to pin mod the chip before i can see any real results. i attempted it today foe 1.8, and it failed, so later when i get some time, ill try again.

Rasputin'sLiver · 07-13-02, 04:33 PM

Quote:

Originally posted by jdmcnudgent
yeah, got it. i need to pin mod the chip before i can see any real results. i attempted it today foe 1.8, and it failed, so later when i get some time, ill try again.

which way are you going? wire or defroster? either way, good luck and remember that i had dd reserve a place for you in his 3ghz mafia

jdmcnudgent · 07-13-02, 05:22 PM

Quote:

Originally posted by Rasputin'sLiver

which way are you going? wire or defroster? either way, good luck and remember that i had dd reserve a place for you in his 3ghz mafia

im doing the wire mod, i cant find the defogger kit anywhere around here.

Rasputin'sLiver · 07-13-02, 05:37 PM

Quote:

Originally posted by jdmcnudgent
im doing the wire mod, i cant find the defogger kit anywhere around here.

you'll get it done with the wire. your advice to me was great -- one strand of speaker wire wrapped tight. i pre-tightened it sort of like a noose, crimped the noose end closed as much as possible (kinda shaped like the eye of a needle when it finally worked) I "threaded the needle" with the 2 pins, and then the hard part was twisting it even a little tighter and keeping it on the pins......Arggghhhhhh! it took me at least an hour and one failed install before i got it right. hang in there!

Wallacebw · 07-13-02, 06:31 PM

on this note when I get my 2.26B which method should I use? (asuming that it needs it

) I already have a defoger kit and something like 250+ feet of monster cable...

Either way work better? if not then which is easier...

Brian

Darryl_D · 07-13-02, 06:59 PM

WAIT WAIT WAIT WAIT WAIT

WTF are you guys talking about?? DID JD get a 2.26B???? IS HE DOING IT IS HE TRYING TO HIT 3GHZ!!!! MORE IMPORTANTLY IS HE EVAPORATING THE CHIP!!! NOOOOOOOOOOOOOOOOOOOOOOO i knew it! JD was conspiring against me all along! that's it i'm going to vid pin mod my chip now too! And when i do we'll see how far i can take it past 3017mhz MWHAHAHAHAHA!!! JD good luck! Hope your chip doesn't burn out forcing you to RMA it and delaying you to 3ghz

(doesn't it feel nice to know you have my support

)

jdmcnudgent · 07-13-02, 08:09 PM

Quote:

Originally posted by Darryl_D
WAIT WAIT WAIT WAIT WAIT WTF are you guys talking about?? DID JD get a 2.26B???? IS HE DOING IT IS HE TRYING TO HIT 3GHZ!!!! MORE IMPORTANTLY IS HE EVAPORATING THE CHIP!!! NOOOOOOOOOOOOOOOOOOOOOOO i knew it! JD was conspiring against me all along! that's it i'm going to vid pin mod my chip now too! And when i do we'll see how far i can take it past 3017mhz MWHAHAHAHAHA!!! JD good luck! Hope your chip doesn't burn out forcing you to RMA it and delaying you to 3ghz (doesn't it feel nice to know you have my support )

hey son, no i didnt get a 2.26b, i am trying to get to 3.0 gig the hard way, 1.6a

i missed on the pin mod again.

will try again tomorrow.

i got 437 mhz to go

, and no, i am not using the vapo right now, im on air, thats right air. thank god im not using the vapo, because everytime i mess up on the wire mod, it is a pain in the ass to take off the evaporator. btw, the ram i got is phenominal, it kicks ass.

JudgeDredd · 07-13-02, 09:23 PM

Wow, good luck on that! If you hit 3 GHz on that 1.6A, you'll be the leader of the mafia, cause you paid about $100-150 less and got the same speeds.

Rasputin'sLiver · 07-13-02, 09:45 PM

Quote:

Originally posted by Wallacebw
on this note when I get my 2.26B which method should I use? (asuming that it needs it ) I already have a defoger kit and something like 250+ feet of monster cable...

Either way work better? if not then which is easier...

Brian

I did the wire vid mod, but if you can get the defogger kit that seems to be an easier method. Both work equally well.

micamica1217 · 07-13-02, 10:09 PM

Quote:

Originally posted by Rasputin'sLiver

I did the wire vid mod, but if you can get the defogger kit that seems to be an easier method. Both work equally well.

I agree.

I tryed two times to get the pin methed to work...still no good.

I was like "this is just crazy,I have defogger kit from my amd days."

first try worked...I got more than 2.0v at the ready.
It was just too easy.

mica

Rasputin'sLiver · 07-13-02, 10:16 PM

Quote:

Originally posted by micamica1217

I agree.

I tryed two times to get the pin methed to work...still no good.

I was like "this is just crazy,I have defogger kit from my amd days."

first try worked...I got more than 2.0v at the ready.
It was just too easy.

mica

mica, that wire trick was hard! It worked out for me after a couple of tries, but before I had those couple of tries I had a tough time roping the stupid pins with the wire and making it stay. Took over an hour to get it to work but it's working great now! I did the wire method because I had wire in the house and didn't have to mess with tracking down a defogger kit but it sure would have been easier with the defogger from what you're telling me.

micamica1217 · 07-13-02, 10:21 PM

Quote:

Originally posted by Rasputin'sLiver

mica, that wire trick was hard! It worked out for me after a couple of tries, but before I had those couple of tries I had a tough time roping the stupid pins with the wire and making it stay. Took over an hour to get it to work but it's working great now! I did the wire method because I had wire in the house and didn't have to mess with tracking down a defogger kit but it sure would have been easier with the defogger from what you're telling me.

hell, I never took the mobo out...and did not need laser eye surgery.

mica

JudgeDredd · 07-14-02, 12:05 AM

Can someone explain this "defogger kit" please? I'm a little bit confused...

Maxvla · 07-14-02, 12:08 AM

Quote:

Originally posted by JudgeDredd
Wow, good luck on that! If you hit 3 GHz on that 1.6A, you'll be the leader of the mafia, cause you paid about $100-150 less and got the same speeds.

on that note... has anyone ever gotten a 100% o/c on a 1.6a?

micamica1217 · 07-14-02, 12:33 AM

Quote:

Originally posted by JudgeDredd
Can someone explain this "defogger kit" please? I'm a little bit confused...

used for a car...."rear window defogger repair kit".

can be perchased at any auto supply store.

look here

hope this helps.

micamica1217

JudgeDredd · 07-14-02, 01:13 AM

And it has something that lets you wire wrap easier?

micamica1217 · 07-14-02, 02:00 AM

Quote:

Originally posted by JudgeDredd
And it has something that lets you wire wrap easier?

well all I have to say is look up and hit the link.

mica

Darryl_D · 07-14-02, 05:03 AM

Quote:

Quoted from Maxvla
on that note... has anyone ever gotten a 100% o/c on a 1.6a?

COURSE THEY HAVE!!! Before Rasputin's Liver (wtf man you need a new name) sold his 1.6a it was at 2.7ghz.... CS hawkeye had his chip up to 2.9 ghz at a point (i think...) currently on my 1.8a system i have it at 2.9ghz myself!

07-12-02, 08:10 PM	Thread Starter #1
jdmcnudgent Member Join Date: Jan 2002 Location: tOLEDO, OHIO, the heart of it all!	hey ras, post it here. post it here in this thread. thanks buddie.
	QUOTE Thanks

07-13-02, 01:13 PM	#2
Rasputin'sLiver counselor of clock Join Date: Jun 2002 Location: Cleveland	sorry man. didn't notice your thread until now, but I think you got it already right? How's it working out?
	QUOTE Thanks

07-13-02, 06:31 PM	#7
Wallacebw Member Join Date: May 2002 Location: FL, USA	on this note when I get my 2.26B which method should I use? (asuming that it needs it ) I already have a defoger kit and something like 250+ feet of monster cable... Either way work better? if not then which is easier... Brian
	QUOTE Thanks

07-13-02, 06:59 PM	#8
Darryl_D Member Join Date: Apr 2002	WAIT WAIT WAIT WAIT WAIT WTF are you guys talking about?? DID JD get a 2.26B???? IS HE DOING IT IS HE TRYING TO HIT 3GHZ!!!! MORE IMPORTANTLY IS HE EVAPORATING THE CHIP!!! NOOOOOOOOOOOOOOOOOOOOOOO i knew it! JD was conspiring against me all along! that's it i'm going to vid pin mod my chip now too! And when i do we'll see how far i can take it past 3017mhz MWHAHAHAHAHA!!! JD good luck! Hope your chip doesn't burn out forcing you to RMA it and delaying you to 3ghz (doesn't it feel nice to know you have my support )
	QUOTE Thanks

07-13-02, 09:23 PM	#10
JudgeDredd Member Join Date: Apr 2002 Location: Austin, Texas	Wow, good luck on that! If you hit 3 GHz on that 1.6A, you'll be the leader of the mafia, cause you paid about $100-150 less and got the same speeds.
	QUOTE Thanks

hey ras, post it here.

Internet Services

Website Development

Tech Hardware

07-14-02, 12:05 AM	#15
JudgeDredd Member Join Date: Apr 2002 Location: Austin, Texas	Can someone explain this "defogger kit" please? I'm a little bit confused...
	QUOTE Thanks

07-14-02, 01:13 AM	#18
JudgeDredd Member Join Date: Apr 2002 Location: Austin, Texas	And it has something that lets you wire wrap easier?
	QUOTE Thanks

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search