Notices

Overclockers Forums > Hardware > Cooling
Cooling Discussion of fans, heatsinks, thermal pastes and putting it all together to keep your rig cool
Forum Jump

New Vantec Aeroflow...Its alright....

Post Reply New Thread Subscribe Search this Thread
 
 
Thread Tools
Old 04-02-03, 12:41 AM Thread Starter   #1
daigster
Registered

 
daigster's Avatar 

Join Date: Jan 2003
Location: Canada

 
New Vantec Aeroflow...Its alright....


Just took off loud Volcano 9 that i had running at 3100rpm, and sat at 37idle/42load...and replaced it with a the aeroflow i picked up this weekend...Quieter then the V9, and now, i'm sittin at 28C, idle...havent stressed it yet...will check though...But anyway, so far i'm impressed..and looks sleek compared to that big orange fan i used to have....Now to just get some Stealths to replace 5 loud antec case fans i have...this thing should purr.......
daigster is offline   QUOTE Thanks
Old 04-02-03, 01:40 AM   #2
gooseman
Member



Join Date: Feb 2002
Location: Little Rock, Arkansas

 
I love my Aeroflow. Idle temps at 26 - 28 (depending on room temp) and it just looks good too.

__________________
HEAT

RIG
Asus P4B533-E
P4 2.4b@3.06 1.5v
1 GB Corsair XMS PC3200C2
ATI 9700 PRO
WD 80GB 7200RPM and IBM 30GB 7200RPM Hard Drives
Hercules Game Theater XP
gooseman is offline   QUOTE Thanks
Old 04-02-03, 02:03 AM   #3
hitechjb1
Senior Member



Join Date: Feb 2003

 
It looks good.

It must be a new type of fan since its rpm is higher but gives less noise. 5600 RPM, 35.5 CFM, 38 dbA.

Compared to Vantec Tornado: 5700 RPM, 84.1 CFM, 55.2 dbA

But then the CFM/dbA ratio of the Aeroflow is not as high compared to other fans.

It is probably very good for medium overclocking and medium noise level.

__________________

Overclocking sandbox for A64 939 systems with Winchester and beyond
A64 CPUs, chipsets, motherboards
A64 Overclocking Result Collection
Overclocking sandbox: Tbred B DLT3C and beyond
- DFI LP UT NF4 Ultra-D, Opteron 165 CCBBE 0610 DPMW 3.00 GHz, highest clock 3.30 GHz, XP-90, G. Skill 4800 2 x 512 MB, X800Pro (Winchester 0447 CBBHD 2.83 GHz 314x9 1.52V)
- ABIT NF7-S rev 2.0, Mobile Barton 2600+ IQYHA 0351 MPMW 2.71 GHz (225x12), 18/37 C, 1.89 V, SLK-947U 80mm Tornado (w/ fan control), 512 MB x 2 3500 C2 2-3-2-5, 9500 np -> 9700 np 360/311
- ASUS A7N8X DLX, Tbred B 1700+ 0310 XPMW 2.56 GHz (205x12.5) 1.94 V, max at 2.6 GHz, SLK-800U + TT SFII, 48/40 28/26 C, 512MB 3500 C2 2-3-2-5 (retired)
- Intel 8088 4.77 MHz 8bit CPU, 64KB memory, 1 MB HD, 5 1/4" floppy drive, DOS, 200 bps modem, 80x25 char display

Last edited by hitechjb1; 04-02-03 at 02:21 AM.
hitechjb1 is offline   QUOTE Thanks
Old 04-02-03, 05:56 AM   #4
lazyart
Member

 
lazyart's Avatar 

Join Date: Feb 2003

 
The fan is a Tip Magnetic Drive (TMD) fan.

The movement is generated from the corners rather than the center. With the motor on the outside, there is a smaller center hub. This results in a smaller dead spot for more efficient airflow, along with less noise.

No, I'm not quoting the spec sheet. I have one and love it too.
lazyart is offline   QUOTE Thanks

Post Reply New Thread Subscribe


Overclockers Forums > Hardware > Cooling
Cooling Discussion of fans, heatsinks, thermal pastes and putting it all together to keep your rig cool
Forum Jump

Thread Tools Search this Thread
Search this Thread:

Advanced Search


Mobile Skin
All times are GMT -5. The time now is 02:39 PM.
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
You can add these icons by updating your profile information to include your Heatware ID, Benching Profile ID or your Folding/SETI profile ID. Edit your profile!
X

Welcome to Overclockers.com

Create your username to jump into the discussion!

New members like you have made this the best community on the Internet since 1998!


(4 digit year)

Why Join Us?

  • Share experience
  • Max out your hardware
  • Best forum members anywhere
  • Customized forum experience

Already a member?