Notices

Overclockers Forums > Hardware > Motherboards > AMD Motherboards
AMD Motherboards
Forum Jump

Unstable OC'd SL-75MRN-L Soltek.

Post Reply New Thread Subscribe Search this Thread
 
 
Thread Tools
Old 06-21-03, 05:19 AM Thread Starter   #1
huneycutt
Member



Join Date: May 2003
Location: SC

 
Unstable OC'd SL-75MRN-L Soltek.


Have the above board and it is a honey.
Slight problem when I OC my Athalon 2100+ downgrade 2600 T'bred B core to 2166MHz. Normaly would run 1733MHZ with fsb 133. The only thing I do is jack the fsb up to 166 and get 2166MHz same as a 2700 would normally run.

With fsb at 166, occasionaly when I boot it gets to the desktop with the hour glass beside the pointer and hangs there. I can move the pointer but clicking icons does nothing. I reboot and it works fine. At 166 occasionally when I'm surfing, typing a letter or doing whatever I get the "blue scream-screen" saying the system is busy and punching any key to continue does not work so I have to reboot.

This indicates to me some minor degree of unstability when running at 166 because as long as I run fsb 133 it works like a dream for hours on end, boots first time every time and rarely do I see the blue scream. I know fsb 133 causes the CPU to run at normal speed of 1733MHz. (Running ME for my own reasons.)
I doubt the CPU is getting to hot because I use a good cooler with Arctic Silver II compound with case fan(s) and rarely see the CPU temp over 40C.
http://www.nexfan.com/evcucoacofrs1.html
(Picture shows one tab clip but it now comes with the three tab clip.)

Senior citizen here relatively new to OC'ing and wondering if there is anything I need to set in the BIOS other than just selecting the 166 fsb. I see settings for voltages and other things I know absolutely nothing about. Thought maybe when I go with 166 I should kick the voltage, or whatever, up a notch, but I don't know what to kick or why.

Computers always fascinated me since way back 'younder when I bought my first Tandy 1000SX at Radio Shack, a real screamer with TWO 3.5 floppy drives. We bad, we bad! (I told you I'm a senior . . .) Little over a year ago I built my first one and got a real kick out of it and had a ball.
'Preciate any help & advice ya'll could share. OldBird
huneycutt is offline   QUOTE Thanks
Overclockers Approved
Which motherboard should you buy? Get the final word here. Check out the latest Overclockers reviews:
ASRock Z77 OC Formula Motherboard Review

ASRock teamed up with overclocker Nick Shih to make a high-end overclocking-based, yet functional for all users, motherboard named the Z77 OC Formula. It appears they have achieved it. Read More.

Get it at NewEgg for $239.99
ASUS Maximus V Formula Motherboard

The Maximus V Formula is part of the ROG (Republic of Gamers) series of motherboards, which in itself brings a high level of expectation. It's a no brainer, Overclockers Approved! Read more.

Get it at NewEgg for $279.99
Old 06-21-03, 06:04 AM   #2
bill
Member

 
bill's Avatar 

Join Date: Jan 2003

 
Smile


1st you shouldnt make that big of a jump, you want to go slowly. go up a little then test the stablity .you go till its unstable then adjust the v-core voltage .025v at a time till its stable "keep an eye on your temps" go a little more then test and so on. you dont want your load temps much higher then 50c. if you get to that point you need better cooling. there are plenty of guide's to overclocking on this site and others or just start another thread. i have to get back to work but im sure someone else spot your thread soon. talk with you later. good luck.
i almost forgot post some more info about you rig(see my sig below) the more we know the more we can help.
bill is offline   QUOTE Thanks
Old 06-21-03, 07:29 AM Thread Starter   #3
huneycutt
Member



Join Date: May 2003
Location: SC

 
The fsb has only two options I use, 133 & 166 and I don't know how to adjust it to say 150. If I did I'm certain that would solve the problem.

"you go till its unstable then adjust the v-core voltage .025v at a time till its stable "keep an eye on your temps" go a little more then test and so on." That I can handle. Thanks for the help.

Gotta' get busy on some honey-do's so might play it with some this afternoon.
huneycutt is offline   QUOTE Thanks
Old 06-21-03, 09:38 AM   #4
bill
Member

 
bill's Avatar 

Join Date: Jan 2003

 
There should be an adjustment called something like cpu interface that when you open it should say turbo/aggresive/expert? adjust it to expert. if you cant find that try lowering the multiplyer & go with 166fsb. the owners manual should say something.
bill is offline   QUOTE Thanks
Old 06-21-03, 10:05 AM   #5
mattspalace
I been Dolk'ed Senior

 
mattspalace's Avatar 

Join Date: Jan 2003
Location: Stuttgart, Germany

 
Yes, there are expert settings for memory frequency. You'll have to set expert for your CPU, and then expert will show up until the memory settings.
I have the SL-FRN2-RL right now, but tomorrow or Monday I'll be changing over to the system in my sig.

I would also like to know all of your voltages and system components.

__________________
Case: Cooler Master HAF XM
Motherboard: Asus P8Z77-V
RAM: G-Skill Ripjaws X-Series 16GB DDR3-1600
SSD: 2 X 120GB Kingston Hyper-X 3K in RAID-0
CPU: Intel i7 3770K @ 4.2GHz - 1.18V
CPU Cooler: Thermaltake Water 2.0 Extreme
Video Card: EVGA GTX 670 FTW Edition
PSU: Corsair AX-750
Monitor: Dell U2410
mattspalace is offline Benching Profile Heatware Profile   QUOTE Thanks
Old 06-21-03, 01:34 PM Thread Starter   #6
huneycutt
Member



Join Date: May 2003
Location: SC

 
Cool Running OK now.


Got all of that info fine and I thank you.

I poked around in the BIOS before I read the replies and sort of scared me because this box runs good and fast and I didn't want to fry something by making asjustments I know nothing about.
Discretion IS the better part of valor.

For kicks I loaded the BIOS defaults and Device Mgr now shows me Athalon 2700+ with not one sign of instability since loading defaults and it's been on all day. For the time being I'll let well enough alone 'cause we have to get ready to go party down with my SC red neck buddies. ;-}

I thought my first post pretty well covered my system but here's more; 40Gig Maxtor Ultra ATA Diamond Plus 7200RPM, 512MB Crucial RAM, LiteOn DVD, LiteOn CDRW, Internal ZIP, typical mid tower metal case, one 30CFM exaust fan, one 30CFM intake.
'Das about it . . .
huneycutt is offline   QUOTE Thanks
Old 06-21-03, 01:56 PM Thread Starter   #7
huneycutt
Member



Join Date: May 2003
Location: SC

 
To mattspalace:


Congrats on getting hitched, I know you're excited and I wish ya'll a long and fruitful marriage filled with abundant joy, health and prosperity. Little over 28 years ago I married a great gal and it has been one hell'ava party. It ain't all one big bed of roses, it's a give and take thing, you give 75% and she gives 75% and you have a nice 50% overlap to allow for personal defects.

Many years ago I read this:
"I am not here to live up to your expectations and you are not here to live up to mine, but if by chance we could meet somewhere in between it would be beautiful."
I guess it boils down to tolerance, compassion and compromise.
Remember the 75 - 75.

Hug and kiss her every day and tell you how much you love her and never, ever go to bed angry at each other.
A very wise old Black man once told me,
"Always be careful what goes out of your mouth for it can never go back in." When you argue, and you will, chose your words very carefully. Sharp tounges cause severe wounds that can be healed with apoligies, but the scar will always be there. In ALL ways be kind to one another. I hope ya'll have a good life together.

Gotta' get ready to go to a shin-dig so catch up wif' ya' later.
OldBird
huneycutt is offline   QUOTE Thanks

Post Reply New Thread Subscribe


Overclockers Forums > Hardware > Motherboards > AMD Motherboards
AMD Motherboards
Forum Jump

Thread Tools Search this Thread
Search this Thread:

Advanced Search


Mobile Skin
All times are GMT -5. The time now is 01:25 PM.
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
You can add these icons by updating your profile information to include your Heatware ID, Benching Profile ID or your Folding/SETI profile ID. Edit your profile!
X

Welcome to Overclockers.com

Create your username to jump into the discussion!

New members like you have made this the best community on the Internet since 1998!


(4 digit year)

Why Join Us?

  • Share experience
  • Max out your hardware
  • Best forum members anywhere
  • Customized forum experience

Already a member?