Upgraded from P2 to Cellery 2.2

Foxie3a · 06-17-04, 05:56 PM

I think that I'm the only person here that has a Celeron.. lol

I got a good deal on it with an Asus P4B266.

It runs Windows stable at 133x22=2.9ghz. Although, last night I think that it restarted on its own, not sure though. Its kept at 100F-ish temps all the time, and is at 1.575v.

Currently my RAM is limiting me from going to 3ghz or above.

Prime95 didn't even last a minute though, and RAM is at stock.

Think I should even try 1.6v? I'm so familiar with my P2 I dont know anything about this celeron.

But dont worry guys, I'll get a better mobo with a REAL P4 soon.

amical · 06-18-04, 06:30 AM

I have a celeron 2.4@2.8 it is limmited by my PC2700 Ram that is Generic. The cpu temp is 32 C/89 F (air cooled). You have a huge jump in mhz that needs a higher voltage tweek, (you should do a full load test again with the 1.6v or higher). But getting higher rated ram will help if you decide to go higher. My CPU can get up to 3.0Ghz with the ram i have but works slower than at 2.8GHz.

Hope it works out.

Sjaak · 06-18-04, 07:28 AM

Your CPU will need (much) more voltage.

Seen cellys hit 4Ghz+ on 1.9v

CandymanCan · 06-18-04, 07:31 AM

Run prime95 to see ifi ts stable. I usally run ti for about 5 hrs before overclocking the cpu or memory more.

theflyingrat · 06-18-04, 04:33 PM

The Northwood Cellies are like the Northwood P4s in that you can "safely" (give or take that expression) give them about 1.65v before they begin to either slowly wear out or flat-out die. Of course, they won't always do this; you just run a much greater risk of this happening.

I had a 2.0 Cellie for a while that ran 2.8 all day and all night. Which reminds me... what did I do with that thing? I can't even remember if I sold it or what! Oh, well. It was a fine machine for some gaming (with my old Ti4200) and miscellaneous putzing around.

Lancelot · 06-19-04, 02:13 AM

I built a rig for my bro-in-law with a Celly2.4 that instantly ran 3.2Ghz 133FSB, and is now not even topped out at 3.25Ghz 135FSB with 1.575Vcore. It's on my old Asus P4P800 board so I guess it's the only Celly with dual-channel RAM in these forums, lol! Still my kids' rig with a P4 1.7Ghz Willamette (256kB L2, 400FSB) and PC133 SDRAM (yeah baby!) is getting the same daily average SETI WU output...

06-17-04, 05:56 PM	Thread Starter #1
Foxie3a Normal Member Join Date: Sep 2003 Location: Modesto, CA	Upgraded from P2 to Cellery 2.2 I think that I'm the only person here that has a Celeron.. lol I got a good deal on it with an Asus P4B266. It runs Windows stable at 133x22=2.9ghz. Although, last night I think that it restarted on its own, not sure though. Its kept at 100F-ish temps all the time, and is at 1.575v. Currently my RAM is limiting me from going to 3ghz or above. Prime95 didn't even last a minute though, and RAM is at stock. Think I should even try 1.6v? I'm so familiar with my P2 I dont know anything about this celeron. But dont worry guys, I'll get a better mobo with a REAL P4 soon. __________________ Dual Xeon X5482 E0 3.2/12M/1600 (400x8 1.26v) Supermicro X7DWA-N, 14GB ECC/Fully Buffered (400, 5-5-5, 1.8v) Radeon 5770 1GB Triple LCDs (22/22/24") Boot: 5x SAS/15K Drives in RAID5 (~350mb/s) Storage: 17 hard drives from 10K to 15K RPM. All SCSI Hot Swap. PCP&C 1.2KW Single 12v, 90A Rail Auzen X-FI Prelude <- Digital -> Denon Receiver -> Sennheiser HD650 Headphones.
	QUOTE Thanks

06-18-04, 06:30 AM	#2
amical Registered Join Date: Jan 2004 Location: Australia	I have a celeron 2.4@2.8 it is limmited by my PC2700 Ram that is Generic. The cpu temp is 32 C/89 F (air cooled). You have a huge jump in mhz that needs a higher voltage tweek, (you should do a full load test again with the 1.6v or higher). But getting higher rated ram will help if you decide to go higher. My CPU can get up to 3.0Ghz with the ram i have but works slower than at 2.8GHz. Hope it works out.
	QUOTE Thanks

06-18-04, 07:28 AM	#3
Sjaak Member Join Date: Apr 2004 Location: The Netherlands	Your CPU will need (much) more voltage. Seen cellys hit 4Ghz+ on 1.9v __________________ 'Apparantly reality has a strong liberal bias'
	QUOTE Thanks

06-18-04, 07:31 AM	#4
CandymanCan Disabled Join Date: Aug 2003 Location: Woodbridge, Va	Run prime95 to see ifi ts stable. I usally run ti for about 5 hrs before overclocking the cpu or memory more.
	QUOTE Thanks

06-18-04, 04:33 PM	#5
theflyingrat Member Join Date: Apr 2001 Location: St. Paul, MN, USA	The Northwood Cellies are like the Northwood P4s in that you can "safely" (give or take that expression) give them about 1.65v before they begin to either slowly wear out or flat-out die. Of course, they won't always do this; you just run a much greater risk of this happening. I had a 2.0 Cellie for a while that ran 2.8 all day and all night. Which reminds me... what did I do with that thing? I can't even remember if I sold it or what! Oh, well. It was a fine machine for some gaming (with my old Ti4200) and miscellaneous putzing around. __________________ ASUS P8Z68-V LX ; Core i7-2600K @ 4.0GHz ; 8GB (2x4GB) G.Skill RipJaws CL7 DDR3-1333 ; Cooler Master Hyper 212 Plus ; XFX Radeon HD 6950 1GB ; Samsung Spinpoint F3 1TB ; Corsair TX750 ; Windows 7 Ultimate MSI 990XA-GD55 ; FX-4100 @ Stock ; 4GB (2x2GB) Mushkin Silverline DDR3-1333 ; Sunbeam CCTF ; PNY GeForce 7300GS ; Seagate 7200.12 750GB ; BFG GS-550 ; Mint 11 2005 Kawasaki Z750S \| 2001 Aprilia SL1000 Falco \| 2008 Yamaha WR250X
	QUOTE Thanks

Upgraded from P2 to Cellery 2.2

Internet Services

Website Development

Tech Hardware

06-19-04, 02:13 AM	#6
Lancelot Join Date: Feb 2001 Location: the Netherlands	I built a rig for my bro-in-law with a Celly2.4 that instantly ran 3.2Ghz 133FSB, and is now not even topped out at 3.25Ghz 135FSB with 1.575Vcore. It's on my old Asus P4P800 board so I guess it's the only Celly with dual-channel RAM in these forums, lol! Still my kids' rig with a P4 1.7Ghz Willamette (256kB L2, 400FSB) and PC133 SDRAM (yeah baby!) is getting the same daily average SETI WU output... __________________ :: Xeon E3-1220v2 @3745 on Asus P8H77-V with 8GB Corsair DDR3 @1712
	QUOTE Thanks

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search