Got my New Board, what to expect?

Osirus · 07-19-04, 08:40 PM

Ok, After screwing up my Gigabyte 8KNXP Rev2 board, I bought a Abit IC7-G Max2 board, what am I going to expect overclocking wise? Im using a 3.0E on water, Are there anything special I need to know with this new board? THis is my first Abit board I have owned...

THanks for the info!

Osirus · 07-19-04, 10:22 PM

Now I am seeming to have a problem with running my Memory in Dual Channel Mode. I tried both slots and its still in single channel. I updated the BIOS to version 24, (if that helps) Any suggestions on how to get it to work? I changed over boards from the Gigabyte 8KNXP Rev2, to the IC7-G Same Memory and everything.

BigStan · 07-19-04, 10:58 PM

To run dual channel you need to have 2 sticks of identical mem installed in either slots 1~3 or 2~4

Osirus · 07-19-04, 11:05 PM

oh ok.. I have 1 gig of the same memory, but bought at differnet times.

BigStan · 07-19-04, 11:11 PM

Does that mean you have 2x512 or 4x256? Did you buy 2 of the exact same mushkin sticks?

Osirus · 07-19-04, 11:13 PM

I have 2 x 512, same chip, both pc2700 bought at different times

BigStan · 07-19-04, 11:16 PM

and you have them in either slots 1~3 or 2~4?

Osirus · 07-19-04, 11:23 PM

yes.. I tried both of them, and CPUZ reports Single Channel

orionzbelt1 · 07-20-04, 11:44 AM

this might be a stupid question but could it because you are using pc2700 memory if you have it at 1:1 those sticks must be well overclocked

Rich_L · 07-20-04, 02:02 PM

The ID prom(SPD) on the sticks might not be programed the same and if so the BIOS will not enable dual channel mode. You can use CPUZ to read the SPD info to see is the sticks are the same.

Osirus · 07-20-04, 07:17 PM

Stick's arent the same, but I was able to run dual channel on my old Gigabyte 8KNXP board with no problems. Right now, Im not overclocked on the CPU but I have it running at 1:1

I havent overclocked it yet because Im still unsure what are the correct settings for a good overclock.

Osirus · 07-25-04, 12:20 AM

well I got the board to oc at 3.5 stable for 4days as of this writing. Havent been able to get dual channel to run on the board yet. Still looking for suggestions on this.

Can someone tell me what exactly the volt moding on this board does, and is it really worth it?

Evilsizer · 07-25-04, 04:43 PM

Quote:

Originally Posted by Osirus

well I got the board to oc at 3.5 stable for 4days as of this writing. Havent been able to get dual channel to run on the board yet. Still looking for suggestions on this.

Can someone tell me what exactly the volt moding on this board does, and is it really worth it?

the ic7 series including the Max3 has a VTT and Vdimm problem. the vdimm problem is that when you set the voltage to say 3.2 it undervolts (cant remember about that one been a while since i read about it). The vtt is suppose to =1/2 of the vdimm and when you take the Vdimm above, was it 2.9 or 3.0 that the Vtt does not equal 1/2 of vdimm. Worth doing it is up to YOU and wiether or not you know your ram can take the voltage for Higher FSB.

Might be dumb to ask but i noticed after getting my new ram that i was not running dual channel then saw it was only counting half the ram... to you recheck to make sure the ram is seated all the way in? (just an idea)

Osirus · 07-25-04, 04:48 PM

its fully seated, CPUZ reports 1gig 2x512, but only in single mode. What is the deal with GAT. any specific settings to run that at?

meionm · 07-25-04, 05:41 PM

did you install any software that came with the mobo on the disk?

Osirus · 07-25-04, 05:42 PM

just the chipset drives, and flashmenu... and all the other drives for the board.

Evilsizer · 07-25-04, 06:33 PM

Quote:

Originally Posted by Osirus

its fully seated, CPUZ reports 1gig 2x512, but only in single mode. What is the deal with GAT. any specific settings to run that at?

Sounds like rma time on that board since dual channle is not working... i would say you have them in the wrong slots... but that has already been looked at....so i dont have any other ideas.....

Osirus · 07-25-04, 06:36 PM

Ill be damned if I have to rma this board, it was bought on 7/19/2004 from my local pcclub.

could it be the board is picky with memory? what is GAT, there are enabled in that setting, any better settings for GAT?

dual channel was working fine on my gigabyte 8KNXP board.

Evilsizer · 07-25-04, 07:00 PM

gat does not effect you using dual channle.... maybe ram but i dought it... i have an is7 i got for my moms rig that is using sammy 256x2 in dual channle not a prob. @dd340. both of my mem sticks where bought 4months apart from the egg. Like i said the only things i can think of is the ram slots and the mobo possibly not working correctly.... sorry... could always go the abit forums and search around and then post and see what one of the tech support guys say from abit...

Osirus · 07-25-04, 07:02 PM

yeah.. I checked around on the abit forums, didnt give me much help. Ill try a few other things and see if I can get it to work.

07-19-04, 08:40 PM	Thread Starter #1
Osirus Member Join Date: May 2004 Location: Check your Six...	Got my New Board, what to expect? Ok, After screwing up my Gigabyte 8KNXP Rev2 board, I bought a Abit IC7-G Max2 board, what am I going to expect overclocking wise? Im using a 3.0E on water, Are there anything special I need to know with this new board? THis is my first Abit board I have owned... THanks for the info! __________________ HP dv8300us Media Center Lappy
	QUOTE Thanks

07-19-04, 10:22 PM	Thread Starter #2
Osirus Member Join Date: May 2004 Location: Check your Six...	Now I am seeming to have a problem with running my Memory in Dual Channel Mode. I tried both slots and its still in single channel. I updated the BIOS to version 24, (if that helps) Any suggestions on how to get it to work? I changed over boards from the Gigabyte 8KNXP Rev2, to the IC7-G Same Memory and everything. __________________ HP dv8300us Media Center Lappy
	QUOTE Thanks

07-19-04, 10:58 PM	#3
BigStan Member Join Date: Jul 2004 Location: Dallas, TX	To run dual channel you need to have 2 sticks of identical mem installed in either slots 1~3 or 2~4
	QUOTE Thanks

07-19-04, 11:05 PM	Thread Starter #4
Osirus Member Join Date: May 2004 Location: Check your Six...	oh ok.. I have 1 gig of the same memory, but bought at differnet times. __________________ HP dv8300us Media Center Lappy
	QUOTE Thanks

07-19-04, 11:11 PM	#5
BigStan Member Join Date: Jul 2004 Location: Dallas, TX	Does that mean you have 2x512 or 4x256? Did you buy 2 of the exact same mushkin sticks?
	QUOTE Thanks

Got my New Board, what to expect?

Internet Services

Website Development

Tech Hardware

07-19-04, 11:13 PM	Thread Starter #6
Osirus Member Join Date: May 2004 Location: Check your Six...	I have 2 x 512, same chip, both pc2700 bought at different times __________________ HP dv8300us Media Center Lappy
	QUOTE Thanks

07-19-04, 11:16 PM	#7
BigStan Member Join Date: Jul 2004 Location: Dallas, TX	and you have them in either slots 1~3 or 2~4?
	QUOTE Thanks

07-19-04, 11:23 PM	Thread Starter #8
Osirus Member Join Date: May 2004 Location: Check your Six...	yes.. I tried both of them, and CPUZ reports Single Channel __________________ HP dv8300us Media Center Lappy
	QUOTE Thanks

07-20-04, 11:44 AM	#9
orionzbelt1 Member Join Date: May 2004 Location: ESSEX UK	this might be a stupid question but could it because you are using pc2700 memory if you have it at 1:1 those sticks must be well overclocked
	QUOTE Thanks

07-20-04, 02:02 PM	#10
Rich_L Registered Join Date: Jul 2003	The ID prom(SPD) on the sticks might not be programed the same and if so the BIOS will not enable dual channel mode. You can use CPUZ to read the SPD info to see is the sticks are the same.
	QUOTE Thanks

07-20-04, 07:17 PM	Thread Starter #11
Osirus Member Join Date: May 2004 Location: Check your Six...	Stick's arent the same, but I was able to run dual channel on my old Gigabyte 8KNXP board with no problems. Right now, Im not overclocked on the CPU but I have it running at 1:1 I havent overclocked it yet because Im still unsure what are the correct settings for a good overclock. __________________ HP dv8300us Media Center Lappy
	QUOTE Thanks

07-25-04, 12:20 AM	Thread Starter #12
Osirus Member Join Date: May 2004 Location: Check your Six...	well I got the board to oc at 3.5 stable for 4days as of this writing. Havent been able to get dual channel to run on the board yet. Still looking for suggestions on this. Can someone tell me what exactly the volt moding on this board does, and is it really worth it? __________________ HP dv8300us Media Center Lappy
	QUOTE Thanks

07-25-04, 04:48 PM	Thread Starter #14
Osirus Member Join Date: May 2004 Location: Check your Six...	its fully seated, CPUZ reports 1gig 2x512, but only in single mode. What is the deal with GAT. any specific settings to run that at? __________________ HP dv8300us Media Center Lappy
	QUOTE Thanks

07-25-04, 05:41 PM	#15
meionm Member Join Date: Mar 2004	did you install any software that came with the mobo on the disk?
	QUOTE Thanks

07-25-04, 05:42 PM	Thread Starter #16
Osirus Member Join Date: May 2004 Location: Check your Six...	just the chipset drives, and flashmenu... and all the other drives for the board. __________________ HP dv8300us Media Center Lappy
	QUOTE Thanks

07-25-04, 06:36 PM	Thread Starter #18
Osirus Member Join Date: May 2004 Location: Check your Six...	Ill be damned if I have to rma this board, it was bought on 7/19/2004 from my local pcclub. could it be the board is picky with memory? what is GAT, there are enabled in that setting, any better settings for GAT? dual channel was working fine on my gigabyte 8KNXP board. __________________ HP dv8300us Media Center Lappy
	QUOTE Thanks

07-25-04, 07:00 PM	#19
Evilsizer Senior Fourm Spammer Join Date: Jun 2002 Location: Austin,Texas	gat does not effect you using dual channle.... maybe ram but i dought it... i have an is7 i got for my moms rig that is using sammy 256x2 in dual channle not a prob. @dd340. both of my mem sticks where bought 4months apart from the egg. Like i said the only things i can think of is the ram slots and the mobo possibly not working correctly.... sorry... could always go the abit forums and search around and then post and see what one of the tech support guys say from abit... __________________ i7 920@3.6ghz \| Asus R2G \| GK F3-12800CL7D-4GBRH \| Galaxy GTX660 GC \| C650TX \| OCZ VERTEX EX 120GB, VERTEX 250GB i3 330m \| Jetway NF98 \| 2x2gig DDR3-1066 \| pico 120WI i5 2450 \| Jetway JNF9G-QM77 \| 2x2gig DDR3-1333 \| WIP "I Love To Camp!" "Commensing Shock Therapy!" I'm jonnyGURU of jonnyGURU.com and we don't overload PSU's - JonnyGURU HeatWare
	QUOTE Thanks

07-25-04, 07:02 PM	Thread Starter #20
Osirus Member Join Date: May 2004 Location: Check your Six...	yeah.. I checked around on the abit forums, didnt give me much help. Ill try a few other things and see if I can get it to work. __________________ HP dv8300us Media Center Lappy
	QUOTE Thanks

Thread Tools	Search this Thread
Show Printable Version Email this Page	Search this Thread: Advanced Search