[overdoze]

[22 23:50] Protein: p1301_1RYP_AAAA_UM
[22 23:50]
[22 23:51] Writing local files
[22 27:32] Writing local files
[22 27:35] Completed 0 out of 100000 steps (0%)
[03 52:21] Writing local files
[03 52:24] Completed 1000 out of 100000 steps (1%)
[08 57:42] Writing local files
[08 57:44] Completed 2000 out of 100000 steps (2%)
[14 02:16] Writing local files
[14 02:19] Completed 3000 out of 100000 steps (3%)


[22 25:42] Protein: p1214_Fsnat99_gbsa305K
[22 25:42] - Run: 0 (Clone 97, Gen 18)
[22 25:42] - Frames Completed: 0, Remaining: 500
[22 25:42] - Dynamic steps required: 2500000
[22 25:42]
[22 25:42] Writing local files:
[22 25:42]
[22 25:42] parameters work/wudata_01.prm
[22 25:42] - Writing "work/wudata_01.key": (overwrite) successful.
[22 25:42] - Writing "work/wudata_01.xyz": (overwrite) successful.
[22 25:42] - Writing "work/wudata_01.prm": (overwrite) successful.
[22 25:45] - Writing "work/wudata_01.key": (append) successful.
[22 25:45]
[22 25:45] PROJECT="work/wudata_01", NSTEPS=2500000, DT=2.0000, DTDUMP=10.000000, TEMP=305.00
[22 25:46] TINKER: Software Tools for Molecular Design
[22 25:46] Version 3.8 October 2000
[22 25:46] Copyright (c) Jay William Ponder 1990-2000
[22 25:46] portions Copyright (c) Michael Shirts 2001
[22 25:46] portions Copyright (c) Vijay S Pande 2001
[23 08:56] Finished a frame (1)
[23 32:20] Finished a frame (2)
[23 55:49] Finished a frame (3)
[00 19:15] Finished a frame (4)
[00 42:45] Finished a frame (5)

If you guess right I will send you a heatsink free if you pay for shipping
I currently use this heatsink on XP3200 at default, temp at full load is around 45C

[seadave77]

PII 300

[Clean_Baldy]

its a Pentium III

[Xenocide]

pIII 667

[Loud]

K6-2

[Mark620]

Xp2200

Edit: how often can we guess?

[Audioaficionado]

You guys are just throwing out WAGs. My 1500 SSE CPU does that Big packet in 25 minutes per frame. The one shown does 'em in 5 Hrs and 5 minutes per frame so it doesn't have SSE.

It does 88 point 500 frame Tinkers at the frame rate of ~24 minutes @ 0.176 points per frame. A 2200MHz Barton will do a 235 point 400 frame Tinker at a frame rate of ~5 minutes @ 0.5875 points per frame.

So my estimate is a 180MHz CPU. That's got to be a PI, PPro or K6.

[Rav]

Celeron ~333Mhz

[new_novice]

P Iii 800

[seadave77]

You guys are just throwing out WAGs.

Mine's a SWAG thank you.

[overdoze]

OK all very good guess but not correct yet. Keep on trying guys and gals. And No you can not guess again Just one shot to let other guess as well
Thanks for participate.

Edit: Clean_Baldy please be clear what kind of cpu as there are many different PIII
Edit: Some are closer than other but still not right yet.

[Audioaficionado]

If it was a PIII it should have SSE and do those BigPackets faster. Scaled against my 1500MHz SSE CPUs it would be 120MHz at the SSE rate. I did the math in my head. If you do it more carefully you'll get closer to the actual MHz but the exact CPU type will still be a guess at best. When comparing my daughter's XP1700 @ 1500MHz against half of my 3000MHz Xeon (1500MHz), both FAH clients put out around the same PPD/PPW unless it's an SSE2 DGromacs where the Xeon will win. FAH seems to mainly run on the core frequency of the CPU more than any other factor.

[FizzledFiend]

just cause nobody guess I am going to say a cyrix 500 :P

[Audioaficionado]

Cyrix !!?... I never even thought of Cyrix because it's been so long since they were around trying to duke it out with Intel. You never know though...

I have a Cyrix 486DX2/66 that won't even fold a GAH on time

[seadave77]

I am going to say a cyrix 500

I think that's a wonderful guess. Think outside the box!

Clint

[gungeek]

P90

[Foxie3a]

P1 120mhz

[Bon3thugz43v3r]

Duron 500mhz

[PCGUY112887]

P1MX 166mhz...

[dicecca112]

k6-2 500mhz