Notices

Overclockers Forums > Hardware > CPUs > Intel CPUs
Intel CPUs
Forum Jump

intel 2.4C with samsung UCCC oc

Post Reply New Thread Subscribe Search this Thread
 
 
Thread Tools
Old 06-13-06, 03:17 AM Thread Starter   #1
neop
Member

 
neop's Avatar 

Join Date: Nov 2003
Location: zzz

 
intel 2.4C with samsung UCCC oc


i've been trying to solve this problem for a few weeks but still no success

i'm using a 2.4c with a msi neo2-pls 865PE mobo with 2 x 1GB of corsair samsung uccc rams

now is kinda stuck at 254 x 12 which is pretty low oc, 2.5v(lowest possible) to the rams now

tried feeding 2.7v to the uccc but it gives me errors in memtest86 instead

the rams are capable of running at 270+ fsb on a NF4 mobo but cant do so on the 865pe board
is there any way to make it run at 270fsb on the old 865pe ?
or is there some kind of a conflict?

cant find much info cos most ppl are using their uccc with the A64
only 254fsb @ 2.5v pass memtest, basically any other settings and it shows errors

would really need some guidance

__________________
zzz
neop is offline   QUOTE Thanks
Old 06-13-06, 11:14 PM Thread Starter   #2
neop
Member

 
neop's Avatar 

Join Date: Nov 2003
Location: zzz

 
bounce

__________________
zzz
neop is offline   QUOTE Thanks
Old 06-14-06, 12:53 AM   #3
microfire
Member



Join Date: Oct 2001

10 Year Badge
 
Are you certain it is not the limit of the CPU, most did 3GHz however there was the odd 2.4C that never made it there and above stable.
If you think the CPU can do more, try using just one memory stick and see how far it will go, you should get a little higher.
One stick is likely to be better than the other. Give both of them a go each on their own, and see if you can push it some more with the best one.
Other than that I can only suggest tinkering with the chipset settings in the BIOS, add max AGP/NB voltage usually helps, try mixing up the other timing settings that might be on hand for your particular motherboard.

__________________
Intel Core i7-4930K @ 4.2GHz ' Asus P9X79 ' Corsair 32GB DDR3-1600 CL9 ' 2x Gigabyte GTX 660 Ti ' Dell U3014
microfire is offline   QUOTE Thanks
Old 06-16-06, 01:25 AM   #4
Moto7451
Senior Something

 
Moto7451's Avatar 

Join Date: Feb 2004
Location: LA, CA

 
Loosen the timings and add more chipset voltage. Remember that on the A64 you're dealing with an on chip memory controller and with Pentium 4s you're at the mercy of the chipset. Some chipsets can run very high FSB. Others are horrible overclockers. Right now you're running a 1000MHz FSB (quadpumped speed). To my knowledge, the 865 will run about that.

You can try dividers to boost the speed of the memory over that of the FSB and gain more bandwidth.

__________________
Intel C2D e6400 @ 375MHz x8 = 3Ghz 1.328v, Gigabyte EP43-UD3L, 3GB DDR2, GeForce 9600GT, 73GB 15K SCSI HD/Adaptec 29160 SCSI Card, 750GB SATA Drive, 320GB ATA Drive, HDTV Tuner

D5 Pump Bonneville w/ AC Heater Core Gemeni Cooling Maze 4 Style Water Block

Sager 8690: Core i7 940XM Exreme 2.13GHz (3.2GHz Turbo), 4GB DDR3, GeForce GTX 285M 1GB, 15.6" 1080 LCD, 320GB 7200RPM HD

Difference Between D5 Revisions + flow mod Difference between NPSM & G1/4
Moto7451 is offline   QUOTE Thanks
Old 06-18-06, 01:27 PM   #5
reef
Registered



Join Date: Mar 2003
Location: Yorkshire, UK

 
This was a well known problem with i865/i875 boards and certain types of RAM. It most commonly occured on Winbond CH5 sticks (hence the atttraction at the time of BH5 over CH5). Common symptoms were a complete brick wall at 255MHz FSB no matter what memory voltage or dividers are used. Either the system posts and errors out or all you get are beeps. The same happens on my IC7 when CH5 memory is used, yet with BH5 all is well. Unfortunately there is no fix, all you could ever do was try different memory types.
reef is offline   QUOTE Thanks

Post Reply New Thread Subscribe


Overclockers Forums > Hardware > CPUs > Intel CPUs
Intel CPUs
Forum Jump

Thread Tools Search this Thread
Search this Thread:

Advanced Search


Mobile Skin
All times are GMT -5. The time now is 08:06 PM.
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
You can add these icons by updating your profile information to include your Heatware ID, Benching Profile ID or your Folding/SETI profile ID. Edit your profile!
X

Welcome to Overclockers.com

Create your username to jump into the discussion!

New members like you have made this the best community on the Internet since 1998!


(4 digit year)

Why Join Us?

  • Share experience
  • Max out your hardware
  • Best forum members anywhere
  • Customized forum experience

Already a member?