New to OC and reading alot of info.
I just built a system listed below. I dont want to burn the thing up and just making sure I have done my homework so far. Is there anything in voltages I might change to get some of those temp's down? Worried about the MCP and SPP the most.
Not water cooling but I did buy a Noctua NH-U9B CPU Cooler
and artic silver #5 for contact. Any help or recommendations would be greatly appreciated.
SYSTEM
CASE
Antec 700 two
Motherboard
CPU Type QuadCore Intel Core 2 Quad Q9400, 3200 MHz (8 x 400)
Motherboard Name EVGA E179 (2 PCI, 2 PCI-E x1, 3 PCI-E x16, 4 DDR3 Motherboard Chipset nVIDIA nForce 790i SLI
System Memory 2560 MB (DDR3-1066 DDR3 SDRAM)
DIMM3: Corsair XMS3 DHX CM3X2G1600C9DHX 2 GB DDR3-1066 DDR3 SDRAM (7-7-7-20 @ 533 MHz) (6-6-6-18 @ 457 MHz)
DIMM4: Corsair XMS3 DHX CM3X2G1600C9DHX 2 GB DDR3-1066 DDR3 SDRAM (7-7-7-20 @ 533 MHz) (6-6-6-18 @ 457 MHz)
Display
Video Adapter NVIDIA GeForce GTS 250 (512 MB)
Video Adapter NVIDIA GeForce GTS 250 (512 MB)
3D Accelerator nVIDIA GeForce GTS 250
Monitor Gateway FHD2401 [24" LCD] (M1Z88D0R02377)
Realtek ALC888/1200 @ nVIDIA nForce 570 SLI (MCP55P) - High Definition Audio Controller
Disk Drive WDC WD30 00HLFS-01G6U SCSI Disk Device (279 GB)
Temperatures
Motherboard 37 °C (99 °F)
CPU 37 °C (99 °F)
CPU #1 / Core #1 40 °C (104 °F)
CPU #1 / Core #2 38 °C (100 °F)
CPU #1 / Core #3 41 °C (106 °F)
CPU #1 / Core #4 35 °C (95 °F)
SPP 54 °C (129 °F)
MCP 68 °C (154 °F)
GPU1: GPU Diode 46 °C (115 °F)
GPU2: GPU Diode 44 °C (111 °F)
WDC WD3000HLFS-01G6U0 34 °C (93 °F)
Cooling Fans
CPU 1308 RPM
nForce 4211 RPM
Voltage Values
CPU Core 1.22 V ( I locked this the rest below are on auto in bios)
+3.3 V 3.28 V
+5 V 4.92 V
+12 V 12.04 V
+5 V Standby 4.97 V
VBAT Battery 3.01 V
North Bridge Core 1.42 V
DIMM 1.47 V
In bios i also set :
Linked & Sync'd
both FSB and memory are set to 1600 for 3.2Ghz
I also have EGA VDroop control disabled.
I just built a system listed below. I dont want to burn the thing up and just making sure I have done my homework so far. Is there anything in voltages I might change to get some of those temp's down? Worried about the MCP and SPP the most.
Not water cooling but I did buy a Noctua NH-U9B CPU Cooler
and artic silver #5 for contact. Any help or recommendations would be greatly appreciated.
SYSTEM
CASE
Antec 700 two
Motherboard
CPU Type QuadCore Intel Core 2 Quad Q9400, 3200 MHz (8 x 400)
Motherboard Name EVGA E179 (2 PCI, 2 PCI-E x1, 3 PCI-E x16, 4 DDR3 Motherboard Chipset nVIDIA nForce 790i SLI
System Memory 2560 MB (DDR3-1066 DDR3 SDRAM)
DIMM3: Corsair XMS3 DHX CM3X2G1600C9DHX 2 GB DDR3-1066 DDR3 SDRAM (7-7-7-20 @ 533 MHz) (6-6-6-18 @ 457 MHz)
DIMM4: Corsair XMS3 DHX CM3X2G1600C9DHX 2 GB DDR3-1066 DDR3 SDRAM (7-7-7-20 @ 533 MHz) (6-6-6-18 @ 457 MHz)
Display
Video Adapter NVIDIA GeForce GTS 250 (512 MB)
Video Adapter NVIDIA GeForce GTS 250 (512 MB)
3D Accelerator nVIDIA GeForce GTS 250
Monitor Gateway FHD2401 [24" LCD] (M1Z88D0R02377)
Realtek ALC888/1200 @ nVIDIA nForce 570 SLI (MCP55P) - High Definition Audio Controller
Disk Drive WDC WD30 00HLFS-01G6U SCSI Disk Device (279 GB)
Temperatures
Motherboard 37 °C (99 °F)
CPU 37 °C (99 °F)
CPU #1 / Core #1 40 °C (104 °F)
CPU #1 / Core #2 38 °C (100 °F)
CPU #1 / Core #3 41 °C (106 °F)
CPU #1 / Core #4 35 °C (95 °F)
SPP 54 °C (129 °F)
MCP 68 °C (154 °F)
GPU1: GPU Diode 46 °C (115 °F)
GPU2: GPU Diode 44 °C (111 °F)
WDC WD3000HLFS-01G6U0 34 °C (93 °F)
Cooling Fans
CPU 1308 RPM
nForce 4211 RPM
Voltage Values
CPU Core 1.22 V ( I locked this the rest below are on auto in bios)
+3.3 V 3.28 V
+5 V 4.92 V
+12 V 12.04 V
+5 V Standby 4.97 V
VBAT Battery 3.01 V
North Bridge Core 1.42 V
DIMM 1.47 V
In bios i also set :
Linked & Sync'd
both FSB and memory are set to 1600 for 3.2Ghz
I also have EGA VDroop control disabled.