Hi
I seem to be having a few issues running my XMS3 TW3X4G4096-1800C8DF in my Rampage extreme mobo, and qx9650.
I am trying to get my RAM stable but having a few issues.
I have:
Extreme Tweaker
Ai Overclock Tuner: Manual
OC From Memory Level Up: Auto
FSB Frequency: 450
CPU Ratio Setting: 7
CPU Configuration
C1E Support: Disabled
CPU TM Function: Enabled
Max CPUID Value Limit: Disabled
Vanderpool Technology: Enabled
Execute Disable Bit: Enabled
Core Multi-Processing: Enabled
CPU Clock Skew: Auto
NB Clock Skew: Auto
FSB Strap to North Bridge: 333
PCIE Frequency: 100
DRAM Frequency: 1441Mhz
DRAM Command Rate: 2N
DRAM Timing Control: Manual
1st Information: 8-8-8-21-5-74-10-5
CAS# Latency:8
RAS# to CAS# Delay: 8
RAS# Pre Time: 8
RAS# ACT Time: 24
RAS# To RAS# Delay: AUTO
REF Cycle Time: AUTO
WRITE Recovery Time: AUTO
READ to Pre Time: AUTO
2nd Information :9-5-6-4-7-4-7
READ to WRITE Delay (S/D): AUTO
WRITE to READ Delay (S): AUTO
WRITE to READ Delay (D): AUTO
READ to READ (S): AUTO
READ to READ (D): AUTO
WRITE to WRITE (S): AUTO
WRITE to WRITE (D): AUTO
3RD Information: 21-7-1-9-9
WRITE to PRE Delay: AUTO
READ to PRE Delay: AUTO
PRE to PRE Delay: AUTO
ALL PRE to ACT Delay: AUTO
ALL PRE to REF Delay: AUTO
DRAM Static Read Control: disabled
DRAM Dynamic Write Control: disabled
DRAM Skew Control
DRAM CMD Skew on Channel A: Auto
DRAM CLK Skew on DIMM A1: Auto
DRAM CLK Skew on DIMM A2: Auto
DRAM CTL Skew on DIMM A1: Auto
DRAM CTL Skew on DIMM A2: Auto
DRAM CMD Skew on Channel B: Auto
DRAM CLK Skew on DIMM B1: Auto
DRAM CLK Skew on DIMM B2: Auto
DRAM CTL Skew on DIMM B1: Auto
DRAM CTL Skew on DIMM B2: Auto
Ai Clock Twister: Lighter
Ai Transaction Booster: Manual
Common Performance Level: 10
Pull-In of CHA PH1: Disabled
Pull-In of CHA PH2: Disabled
Pull-In of CHA PH3: Disabled
Pull-In of CHB PH1: Disabled
Pull-In of CHB PH2: Disabled
Pull-In of CHB PH3: Disabled
EPU II Phase Control: Auto
CPU Voltage: 1.31
Load-Line Calibration: Enabled
CPU PLL Voltage: 1.5
FSB Termination Voltage: 1.41
CPU GTLVerf (0): AUTO
CPU GTLVerf (1): AUTO
CPU GTLVerf (2): AUTO
CPU GTLVerf (3): AUTO
NB GTLVerf: AUTO
North Bridge Voltage: 1.42
DRAM Voltage: 1.85
NB DDRVref: AUTO
DDR3 ChannelA Vref: AUTO
DDR3 ChannelB Vref: AUTO
South Bridge 1.5 Voltage: 1.51106
South Bridge 1.05 Voltage: 1.06039
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
I am a bit unsure about the GTL refs etc which I am sure is my issue..however not knowing too much about them I am unsure what to change to try to get stable.
I have been able to run memtest no worries at these settings @ 1350Mhz.
As this ram is rated at 1800 i would have thought I would be stable at 1441Mhz but fail memtest within 10 mins everytime. Again in need of more tweaking which it where yu guys come in
I have the CPU running at stock as I have dropped the multi to keep that out of the picture -and have run Intel Burn test and Prime and the CPU is stable.
Where should I start?
I seem to be having a few issues running my XMS3 TW3X4G4096-1800C8DF in my Rampage extreme mobo, and qx9650.
I am trying to get my RAM stable but having a few issues.
I have:
Extreme Tweaker
Ai Overclock Tuner: Manual
OC From Memory Level Up: Auto
FSB Frequency: 450
CPU Ratio Setting: 7
CPU Configuration
C1E Support: Disabled
CPU TM Function: Enabled
Max CPUID Value Limit: Disabled
Vanderpool Technology: Enabled
Execute Disable Bit: Enabled
Core Multi-Processing: Enabled
CPU Clock Skew: Auto
NB Clock Skew: Auto
FSB Strap to North Bridge: 333
PCIE Frequency: 100
DRAM Frequency: 1441Mhz
DRAM Command Rate: 2N
DRAM Timing Control: Manual
1st Information: 8-8-8-21-5-74-10-5
CAS# Latency:8
RAS# to CAS# Delay: 8
RAS# Pre Time: 8
RAS# ACT Time: 24
RAS# To RAS# Delay: AUTO
REF Cycle Time: AUTO
WRITE Recovery Time: AUTO
READ to Pre Time: AUTO
2nd Information :9-5-6-4-7-4-7
READ to WRITE Delay (S/D): AUTO
WRITE to READ Delay (S): AUTO
WRITE to READ Delay (D): AUTO
READ to READ (S): AUTO
READ to READ (D): AUTO
WRITE to WRITE (S): AUTO
WRITE to WRITE (D): AUTO
3RD Information: 21-7-1-9-9
WRITE to PRE Delay: AUTO
READ to PRE Delay: AUTO
PRE to PRE Delay: AUTO
ALL PRE to ACT Delay: AUTO
ALL PRE to REF Delay: AUTO
DRAM Static Read Control: disabled
DRAM Dynamic Write Control: disabled
DRAM Skew Control
DRAM CMD Skew on Channel A: Auto
DRAM CLK Skew on DIMM A1: Auto
DRAM CLK Skew on DIMM A2: Auto
DRAM CTL Skew on DIMM A1: Auto
DRAM CTL Skew on DIMM A2: Auto
DRAM CMD Skew on Channel B: Auto
DRAM CLK Skew on DIMM B1: Auto
DRAM CLK Skew on DIMM B2: Auto
DRAM CTL Skew on DIMM B1: Auto
DRAM CTL Skew on DIMM B2: Auto
Ai Clock Twister: Lighter
Ai Transaction Booster: Manual
Common Performance Level: 10
Pull-In of CHA PH1: Disabled
Pull-In of CHA PH2: Disabled
Pull-In of CHA PH3: Disabled
Pull-In of CHB PH1: Disabled
Pull-In of CHB PH2: Disabled
Pull-In of CHB PH3: Disabled
EPU II Phase Control: Auto
CPU Voltage: 1.31
Load-Line Calibration: Enabled
CPU PLL Voltage: 1.5
FSB Termination Voltage: 1.41
CPU GTLVerf (0): AUTO
CPU GTLVerf (1): AUTO
CPU GTLVerf (2): AUTO
CPU GTLVerf (3): AUTO
NB GTLVerf: AUTO
North Bridge Voltage: 1.42
DRAM Voltage: 1.85
NB DDRVref: AUTO
DDR3 ChannelA Vref: AUTO
DDR3 ChannelB Vref: AUTO
South Bridge 1.5 Voltage: 1.51106
South Bridge 1.05 Voltage: 1.06039
CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled
I am a bit unsure about the GTL refs etc which I am sure is my issue..however not knowing too much about them I am unsure what to change to try to get stable.
I have been able to run memtest no worries at these settings @ 1350Mhz.
As this ram is rated at 1800 i would have thought I would be stable at 1441Mhz but fail memtest within 10 mins everytime. Again in need of more tweaking which it where yu guys come in
I have the CPU running at stock as I have dropped the multi to keep that out of the picture -and have run Intel Burn test and Prime and the CPU is stable.
Where should I start?
Last edited:
