Notices

Overclockers Forums > Hardware > Motherboards > Intel Motherboards
Intel Motherboards
Forum Jump

775 Socket Pin Replacement - A Method

Post Reply New Thread Subscribe Search this Thread
 
 
Thread Tools
Old 01-03-10, 04:54 AM Thread Starter   #1
robotnz1
New Member



Join Date: Jan 2010

 
775 Socket Pin Replacement - A Method


Hi All,

I was deep in custard today after breaking head off pin in alignment attempt. I couldn't find much on the net to help me.

Here is the solution I worked out!! - Please enjoy!!

Project = Intel Socket 775 Pin Replacement!!

Rules - important!
1. You are already deep in **** - so don't take more risks when using this procedure. Operate accurately and only where you need to.

2. You need to see what you are doing all the time - so use whatever glasses you need. I used a pair of grade 4 over a pair of grade 2.5 - call that what you like but it looks like 6.5 x the reality to me. :-)

Note: A jeweler's or printers 20x or 30x magnifying loupe is also a great help for the hard parts of this project. On reflection I think I could not have done this job successfully without my printers loupe. Using a loupe, as well as very strong glasses, will give you a work place around a 1/8th size of the attached image.

3. Don't damage other pins - if you are careful this procedure should not touch any other pins. It may help to bend the pin behind the one you are repairing up to give more room. IF YOU DO DON'T FORGET TO BEND IT BACK DOWN LATER! But I suggest you practice 'replacing' pins on your dead board's socket before attempting your 'real' target project. Once you have become familiar with the procedure and increased your skill with several 'successes' under your belt it's time to use this new skill!!

TIP - REMOVE THE 775 TOP FLIP COVER TEMPORARILY - this will make access much easier, otherwise the cover is a giant pain! It takes a bit of force but it's easily removable and can be returned later.

Tools:
1 pair of angle point tweezers - others work but I liked flat angle points.
1 Stanley or break off tip wide flat knife. It needs to be wide so it’s strong. Set the blade projection to about 1.5 inches from its sleeve support.
1 steel pin - standard dress maker’s type.
1 pair of wide nose pliers - to hold pin.
1 pair of sharp scissors.
1 x Strong 'halogen type' pedestal light - being able to position and angle the head of the lamp is a big help when viewing the project through the magnifying glasses. Aim it so that you have a great close up view.

Materials:
1 reject 775 socket from dead board - this is where you will get the pin/pins needed. Keep an eye on your local PC shops skip bins - or preferably just go ask their technicians for a dead 775 bare board.

Start

1. Prepare pin: Use a flat blade screw driver and lever part of the socket from the dead board. As it breaks away keep all the pieces for they contain your needed pins. From a broken piece of socket gently pull several pins - depending on where the solder broke on the base of the pins, some will come out the top easier and others the bottom. Just cruise along - take your time.
The object at this point is just to get some nice stock for the project. You will drop some and others will flick off the tweezers, so several will likely be needed. Pickup a virgin (unbent) pin in tweezers - hold it by its top - and use the scissors to cut off the solder bulb on its bottom, at the bottom of the "V" above it. Place it carefully to one side. You may need more if you drop it later but you can cut them later as you need them.
Note: don't unfold the pin as the pin/barb combo is used here in it’s entirety - i.e. pin, barb and the spring effect from the folded material - less only the solder bulb (that was) holding it to the PCB.

2. Now - onto your motherboard

Prepare the broken pin: Each pin leg is in a separate hole, the same as the holes you just pulled the needed pins from. The pins are made from one piece of metal. They are folded and the front is the pin and the rear is the barb - holding the pin into the plastic socket hole and also it provides the solder leg, which we need to cut off - at the "V" just above the solder bulb.
Ideally the broken pin should be broken at its shoulder - not at the bottom of the neck below the head!! This is where they usually break if they are played with in straightening attempts. So if your problem pin is broken at the base of the neck, we are going to break it again - this time at the shoulder, before it narrows down towards the head. So using the tweezers grab the pin as low as you can to the plastic socket - ideally right on the socket. Now while you hold it tight, wiggle it back and forth, rocking the tweezers at the same time to increase the abuse on the metal - until it breaks off. Now we have a normal folded pin, in the socket and broken off at the shoulder!
Next use the dressmakers standard sized (1.25"?) pin - held firmly in the pliers - to push the back portion of the pin (I call it the barb) slightly forward from its resting place. The gap created is where we you are going to push the new replacement pins barb.
Pickup the material (new) pin, you previously found and removed solder bulb from, and holding it the same way as it needs to be - place the barb firmly but gently in the gap you just created. If you drop the pin, invert the motherboard on some white paper and tap it to recover the pin. If it’s lost (make sure it’s not on your board where it could create a short circuit later) get another pin and chop the solder bulb at the bottom of the "V" and use that.
With the new pin (and it’s barb) now behind the old pins barb, pickup the Stanley (or other brand of break off tip) knife - place it vertically, with blade tip between the pin and its folded barb and with point of knife on the top of the steel fold - on the folded side.
What you are going to do here is use the top edge of the fold to push the full barb of the new pin in behind the others barb. Now - using the adjoining pin barb tops as a level guide - push hard to seat the new pins barb top at the same level as the others. This will ensure that the pin projection at the front is the same as all the other pins.
Once the top of the new pins barb is level, using the knife again, tilt the pin neck to the same angle as the others. NOTE: It pays not to touch the pins head - as the pins head is too delicate and it will break off at the base of the fine neck. So, lever on the pin, using the knife, only along the neck – preferable near it’s base – otherwise you risk bending the neck itself, rather than the area below the neck, to position the head. There is plenty of neck length to use.
Now - look carefully at the pins head - the idea is to have it nestling into the shoulder of the pin in front of it (though higher), when viewed from above. Have a good look at all the other pin head locations to become comfortable with the exact location needed.
To align your pin head (back and forth), using the neck only, Use knife, held with blade horizontal against the vertical part of the pin, below the neck, to push it and its barb back against the socket pocket's rear wall if needed - ideally you should be pushing on the old pin and its barb, so using it here to also hold the new pin against the rear of the pocket. This is the contact point between the two pins which will convey the electrical current. Otherwise, if barb is not hard against rear pocket wall, the pin head will be too far forward.
Note: If the top of the barb is hard against the rear wall of the socket pocket where the pin is located AND the barb is pressed into the socket till the barb top is level with the others, then this pins head projection, forward, will be the same as the others.
If the head is now sideways from its needed alignment, use the knife edge against the neck, to align it with careful pressure - as required. The intention here is to locate the head, laterally, by bending the pin BELOW the neck/shoulder.
Finally, use the knife to set the pin head level with the others, again using only the neck as the pressure area. Once the pin head is aligned it should look in line with the others from all the X, Y and Z (i.e. forward/back, left/right, up/down directions).

Testing

If you wish to test your new pin use a meter, set on continuity and place one contact on the pin and run the other along the resistors next to the socket position to find a continuity point. Once your meter beeps - if set to beep - or shows a continuity signal - you have proved your repair.

JOB COMPLETED!!
Attached Images
 

Last edited by robotnz1; 01-03-10 at 12:59 PM. Reason: improvement
robotnz1 is offline   QUOTE Thanks
Overclockers Approved
Which motherboard should you buy? Get the final word here. Check out the latest Overclockers reviews:
ASRock Z77 OC Formula Motherboard Review

ASRock teamed up with overclocker Nick Shih to make a high-end overclocking-based, yet functional for all users, motherboard named the Z77 OC Formula. It appears they have achieved it. Read More.

Get it at NewEgg for $239.99
ASUS Maximus V Formula Motherboard

The Maximus V Formula is part of the ROG (Republic of Gamers) series of motherboards, which in itself brings a high level of expectation. It's a no brainer, Overclockers Approved! Read more.

Get it at NewEgg for $279.99
Old 01-04-10, 12:27 AM   #2
Nechen
Member

 
Nechen's Avatar 

Join Date: Dec 2009

 
You're sexy
Nechen is offline   QUOTE Thanks
Old 09-01-10, 10:38 PM   #3
NorthGaLocal
New Member



Join Date: Sep 2010

 
You are a true god among geeks, dude. I have done some pretty outragous back-woods, redneck-tech repairs in my day, but that $h1T takes the cake. Until I found this thread, I thot it to be impossible to 'repair' a LGA socket.

Im so impressed with this process, Im gonna scrounge eBay for bunk boards and try to fix'm. Should work with LGA1366, too huh?
NorthGaLocal is offline   QUOTE Thanks
Old 09-02-10, 12:07 AM   #4
xoke

 
xoke's Avatar 

Join Date: Jun 2010

 
Quote:
Originally Posted by NorthGaLocal View Post
You are a true god among geeks, dude. I have done some pretty outragous back-woods, redneck-tech repairs in my day, but that $h1T takes the cake. Until I found this thread, I thot it to be impossible to 'repair' a LGA socket.

Im so impressed with this process, Im gonna scrounge eBay for bunk boards and try to fix'm. Should work with LGA1366, too huh?
x2!

__________________
Jiggy X58A-UD7 - Intel i7 920 D0 +4.9ghz - Kingston Hyper-X DDr3 2333 - 2x MSI GTX 480
Jiggy 890FXA-UD5 - AMD 1090t BE +6.0ghz - Mushkin Ridgeback DDr3 2000 - 2x Biostar HD 4890 R.I.P.
Antec TPQ 1200w - Sunbeam Tech Bench - WD Raptors - Koolance v2 - 2x K|ngp|n Tek-9 v6 Slim - ShamWow
xoke is offline Author Profile   QUOTE Thanks
Old 09-02-10, 12:38 AM   #5
nd4spdbh2
Member

 
nd4spdbh2's Avatar 

Join Date: Nov 2005
Location: Camarillo, CA!

 
theres a pretty good probability that the pin wasnt even needed as it probably was a ground / power pin... and one less of those wouldnt make a difference.... but regardless awesome write up and to ocf

__________________
#12 in the 4ghz core 2 duo club baby! - 52 inches of CRYSIS! - Black Belt Ubercloxx0r -- Heatware
Main -- Lian Li V2000b -- i7 2700k -- MSI Z68A-GD80 -- 12gb 1600 -- GTX560Ti --Adata 128gb S510 & 2x500gb -- Seasonic S12 600w -- Dell 2209WA
HTPC -- Silverstone GD05B -- E7200 @ 3.2ghz -- G41-M7 -- 4GB 800mhz -- g210 passive -- 320gb 2.5in WD -- Antec EA 430w -- 52inch Samsung LCD
Server -- Antec NSK4480B -- E3300 @ 2.5ghz -- ECS G33T-M2 -- 3gb 667mhz -- Onboard Vid -- 500Gb + 1TB hatachi + 1tb WD -- Zalman 400w
Netbook - Dell Mini 9 - Atom 1.6ghz - 8GB ssd - 2GB pc6400 - WIN 7 PRO!
Need 4 Speed - BH
nd4spdbh2 is offline   QUOTE Thanks
Old 02-23-13, 10:05 PM   #6
SPeEdZ70
Registered



Join Date: Feb 2013
Location: APPLETON U.S.A.

 
WOW


Hi sorry to dredge this up but I just joined because I read this! and been trying to figure this out for hours now I got a older board I really want working 3 pins are broken Off. I broke the socket off a working dell to get the pins but the pins are different than these they are folded in a v shape not like in the picture they are not two pieces that look some how melted together the ones I have are one piece I guess they use different designs guess I`ll have to wreck another board just do not know which one yet I have a P5W DH Deluxe one pin is broken off at the Shoulder it is a VSS pin and not sure if it is really needed but for some reason I can not get the board to go over about 340 FSB I was wondering if that one pin caused it, I read tons about the board before I got it and after tried everything still will not let me put my E7400 that is in it over 3.5~ so It may be the CPU it is an R0.I do not have that nice spot to push down on. Any help here would be appreciated Thanks


B.T.W. The board is a P35-DS3L if it performs anything like my P35C-DS3R I really would like to crank it up if I can get it to boot

Last edited by SPeEdZ70; 02-27-13 at 10:24 AM.
SPeEdZ70 is offline   QUOTE Thanks
Old 02-27-13, 11:26 PM   #7
Armani2468
Member

 
Armani2468's Avatar 

Join Date: Mar 2008
Location: Bostonian

 
Thank you for the pics and write up! Fantastic!

__________________
COOLER MASTER HAF 932 Modded CF
/ CPU I7 2600k 4.7 / 8 G Skill RAM / ASUS WS MB /
/ Raystorm WB /Swiftech KOMODO WB /
/ 27'' LG IPS 2560x1440 / Amazing
/ GTX 780 SLI / OC 1,180 Core Clock / Skynet BIOS /
/ Corsair 1200 PSU / CyberPower CP1500-900 UPS /
/ Razer N52te w/Razer Mamba /
/ XSPC Raystorm WB /
/ XSPC RES w/D5 Vario /
/ XSPC 360 ver.2 w/SP /
/ XSPC EX240 P/P w/SP /
Build Thread http://www.overclockers.com/forums/s...d.php?t=727208
Armani2468 is offline   QUOTE Thanks
Old 03-03-13, 12:17 PM   #8
txus.palacios
Premium Member #18

 
txus.palacios's Avatar 

Join Date: Dec 2011
Location: Cádiz (Spain)

 
Guys, post is three years old!

Great info though, should be on a sticky.

__________________
Maximus V Gene | i5-2500k @ 4.5GHz (ekHF) | 16GiB | GTX470 SLI @ 800MHz (ekFC) | m4 128GB | Arch + Win8
[ more info... ]


The only sound I want to hear out of my computer (unless I'm gaming or watching a movie) is the hum of my 6000 rpm fan pushing air through my heatsink. - Seebs
If I turn up dead, somebody make sure they put "should have just benched in the cold" on my tombstone, along with my most recent superpi32m score. - I.M.O.G.
I didn't go water-cooling for an air-cooling Vcore!! - bluezero5
I'll rm -rf /yourface/* - thideras
txus.palacios is offline Benching Profile Folding Profile   QUOTE Thanks
Old 03-04-13, 07:24 PM   #9
Armani2468
Member

 
Armani2468's Avatar 

Join Date: Mar 2008
Location: Bostonian

 
Yup saw that.... lol Couldn't resist

__________________
COOLER MASTER HAF 932 Modded CF
/ CPU I7 2600k 4.7 / 8 G Skill RAM / ASUS WS MB /
/ Raystorm WB /Swiftech KOMODO WB /
/ 27'' LG IPS 2560x1440 / Amazing
/ GTX 780 SLI / OC 1,180 Core Clock / Skynet BIOS /
/ Corsair 1200 PSU / CyberPower CP1500-900 UPS /
/ Razer N52te w/Razer Mamba /
/ XSPC Raystorm WB /
/ XSPC RES w/D5 Vario /
/ XSPC 360 ver.2 w/SP /
/ XSPC EX240 P/P w/SP /
Build Thread http://www.overclockers.com/forums/s...d.php?t=727208
Armani2468 is offline   QUOTE Thanks

Post Reply New Thread Subscribe


Overclockers Forums > Hardware > Motherboards > Intel Motherboards
Intel Motherboards
Forum Jump

Thread Tools Search this Thread
Search this Thread:

Advanced Search


Mobile Skin
All times are GMT -5. The time now is 09:37 AM.
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
You can add these icons by updating your profile information to include your Heatware ID, Benching Profile ID or your Folding/SETI profile ID. Edit your profile!
X

Welcome to Overclockers.com

Create your username to jump into the discussion!

New members like you have made this the best community on the Internet since 1998!


(4 digit year)

Why Join Us?

  • Share experience
  • Max out your hardware
  • Best forum members anywhere
  • Customized forum experience

Already a member?