E8400 OC Help

[b][u]GIGABYTE GA-EP45-UD3x[/u][/b] 
[u][b][u]MB Intelligent Tweaker(M.I.T.)[/u][/b] 
Robust Graphics Booster ...............:  
CPU Clock Ratio ..........................:  
Fine CPU Clock Ratio.....................:. 
CPU Frequency ...........................: Mhz 
[b][u]Clock Chip Control [/u][/b] 
[b][u]Standard Clock Control[/u][/b] 
CPU Host Clock Control..................: [Enabled] [Disabled] 
CPU Host Frequency (Mhz) ............:Mhz 
PCI Express Frequency (Mhz) .........:Mhz 
C.I.A. 2......................................: Disabled 
[b][u]Advanced Clock Control [Press Enter][/u][/b] 
CPU Clock Drive...........................: mv 
PCI Express Clock Drive.................: mv 
CPU Clock Skew (ps)....................: ps 
MCH Clock Skew (ps)...................: ps 
[b][u]DRAM Performance Control[/u][/b][u][/u] 
Performance Enhance...................: [Turbo] 
Extreme Memory Profile (X.M.P.).....:  
(G)MCH Frequency Latch...............: [Auto] 
System Memory Multiplier ..............: 
Memory Frequency (Mhz) ..............: Mhz 
DRAM Timing Selectable ................: [Manual] 
[b]Standard Timing Control[/b] 
CAS Latency Time..............................:  
tRCD .........................................:  
tRP...........................................:   
tRAS..........................................:   
[b]Advanced Timing Control [Press Enter][/b] 
tRRD...........................................: 
tWTR..........................................: 
tWR............................................: 
tRFC...........................................: 
tRTP...........................................: 
Command Rate (CMD) ....................: 

[b]Channel A[/b] 

[b]Channel A Timings Settings [Press Enter][/b]  
Static tRead Value.........................:Auto 
tRD Phase0 Adjustmen.......................:Auto 
tRD Phase1 Adjustment......................:Auto 
tRD Phase2 Adjustment .....................:Auto 
tRD Phase3 Adjustment......................:Auto 
Trd2rd(Different Rank).....................:Auto  
Twr2wr(Different Rank).....................:Auto  
Twr2rd(Different Rank).....................:Auto  
Trd2wr(Same/Diff Rank).....................:Auto  
Dimm1 Clock Skew Control...................:Auto  ps 
Dimm2 Clock Skew Control...................:Auto  ps 
DDR Write Training ...........................: Enabled 
[b]Channel A Driving Settings [Press Enter][/b]  
Driving Strength Profile...................:[AUTO],[667Mhz],[800Mhz],[1066Mhz],[OC-1200],[OC-1333] 

Data Driving Pull-Up Level.................:Auto  
Cmd Driving Pull-Up Level..................:Auto  
Ctrl Driving Pull-Up Level.................:Auto  
Clk Driving Pull-Up Level..................:Auto  

Data Driving Pull-Down Level...............:Auto  
Cmd Driving Pull-Down Level................:Auto  
Ctrl Driving Pull-Down Level...............:Auto  
Clk Driving Pull-Down Level................:Auto  
[b]Channel B[/b] 

[b]Channel B Timings Settings [Press Enter][/b]  
Static tRead Value.........................:Auto 
tRD Phase0 Adjustmen.......................:Auto 
tRD Phase1 Adjustment......................:Auto 
tRD Phase2 Adjustment .....................:Auto 
tRD Phase3 Adjustment......................:Auto 
Trd2rd(Different Rank).....................:Auto  
Twr2wr(Different Rank).....................:Auto  
Twr2rd(Different Rank).....................:Auto  
Trd2wr(Same/Diff Rank).....................:Auto  
Dimm1 Clock Skew Control...................:Auto  ps 
Dimm2 Clock Skew Control...................:Auto  ps 
DDR Write Training .........................: Enabled 
[b]Channel B Driving Settings [Press Enter][/b]  
Driving Strength Profile...................:[AUTO],[667Mhz],[800Mhz],[1066Mhz],[OC-1200],[OC-1333] 

Data Driving Pull-Up Level.................:Auto  
Cmd Driving Pull-Up Level..................:Auto  
Ctrl Driving Pull-Up Level.................:Auto  
Clk Driving Pull-Up Level..................:Auto  

Data Driving Pull-Down Level...............:Auto  
Cmd Driving Pull-Down Level................:Auto  
Ctrl Driving Pull-Down Level...............:Auto  
Clk Driving Pull-Down Level................:Auto  


[b]{U]Motherboard Voltage Control[/b]{/U] 
Voltage Type.………... Normal  
[b]CPU[/b] 
Load Line Calibration......................: [Enabled] [Disabled] 
CPU Vcore..................................:v 
CPU Termination…..... 1.200V*..............:v 
CPU PLL...............1.500V*..............: v 
CPU Reference.........0.755V*..............: v 
[b]MCH/ICH[/b] 
MCH Core..............1.100V...............: v 
MCH Reference.........0.800V...............: v 
MCH/DRAM Ref..........0.900V...............: v 
ICH I/O...............1.550V...............: v 
ICH Core............……1.100V...............: v 
[B]DRAM[/B] 
DRAM Voltage..........1.800V...............: v 
DRAM Termination......0.900V...............: v 
Channel A Reference...0.900V...............: v 
Channel B Reference...0.900V...............: v 
[b]{U]Advanced Settings[b]{U] 
Limit CPUID Max. to 3......................: [Disabled] 
No-Execute Memory Protect..................: [Disabled] 
CPU Enhanced Halt (C1E)....................: [Disabled] 
C2/C2E State Support.......................: [Disabled] 
x C4/C4E State Support.....................: [Disabled] 
CPU Thermal Monitor 2(TM2) ................: [Enabled] 
CPU EIST Function..........................: [Disabled] 
Virtualization Technology..................: [Disabled] 
[b]Note[/b]: * refers to 45nm CPU

Static tRead Value: 6 to 7 or 8 (on both channels)
tRFC: Auto to 54
Command Rate: Auto to 2T or 2N
CPU Termination Voltage (VTT): 1.2 to 1.25 - 1.3V
MCH Clock Skew: Auto to 50ps (try this last)