- Joined
- Feb 17, 2011
Hello Forum.
A few days ago my Noctua NH-D14 arrived and i decided to do a overclock on my I7 930.
So i went on the internetz and found a few tips/configs and decided to test the following settings listed below.
I ran Prime for 4 hours and it was stable i could run more but not sure if that is needed.
idle temps are 38-42 on a long day of using my pc and 76C on the Prime run.
-So how are m voltages? are they a bit too high or should i keep them like this?
-I used Artic silver 5 instead of the thermalpaste you get with Noctua nh-d14.
was this a good choise? or are the temps a bit too high?
-Would anny of you advice to go to 3,8Ghz to increase the live span of my cpu? or as asked above are these temps and voltages low enough?
Specs:
Antec 1200
Asus P6X58D-E (Bios version 0405)
Intel core i7 930 2,88Ghz @ 4,01Ghz
Noctua NH-D14
Corsair Dominator GT CMT6GX3M3A 7-7-7-20 3x2GB
Nvidia Geforce 9200 LE (9800 GX2 broken so im currently using this till i get my gtx 560 next month)
Superflower 750 Watt PSU
Windows 7 Ultimate 64bit
OC settings:
Ai Overclock Tuner.....................[Manual]
CPU Ratio Setting......................[21.0]
Intel(r) SpeedStep(tm) Tech............[Disabled]
Xtreme Phase Full Power Mode...........[Enabled]
BCLK Frequency.........................[191]
PCIE Frequency.........................[100]
DRAM Frequency.........................[DDR3-1531MHz]
UCLK Frequency.........................[3063MHz]
QPI Link Data Rate.....................[Auto]
CPU Voltage Control....................[Manual]
CPU Voltage............................[1.23125]
CPU PLL Voltage........................[1.80]
QPI/DRAM Core Voltage..................[1.21875]
IOH Voltage............................[1.14]
IOH PCIE Voltage.......................[1.50]
ICH Voltage............................[1.20]
ICH PCIE Voltage.......................[1.50]
DRAM Bus Voltage.......................[1.64]
DRAM DATA REF Voltage on CHA...........[Auto]
DRAM CTRL REF Voltage on CHA...........[Auto]
DRAM DATA REF Voltage on CHB...........[Auto]
DRAM CTRL REF Voltage on CHB...........[Auto]
DRAM DATA REF Voltage on CHC...........[Auto]
DRAM CTRL REF Voltage on CHC...........[Auto]
Load-Line Calibration..................[Enabled]
CPU Differential Amplitude.............[800mV]
CPU Clock Skew.........................[Delay 300ps]
CPU Spread Spectrum....................[Disabled]
IOH Clock Skew.........................[Auto]
PCIE Spread Spectrum...................[Disabled]
C1E Support............................[Disabled]
Hardware Prefetcher....................[Enabled]
Adjacent Cache Line Prefetch...........[Enabled]
Intel(r) Virtualization Tech...........[Disabled]
CPU TM Function........................[Enabled]
Execute Disable Bit....................[Enabled]
Intel(r) HT Technology.................[Enabled]
Active Processor Cores.................[All]
A20M...................................[Disabled]
Intel(r) SpeedStep(tm) Tech............[Disabled]
Intel(r) C-STATE Tech..................[Disabled]
A few days ago my Noctua NH-D14 arrived and i decided to do a overclock on my I7 930.
So i went on the internetz and found a few tips/configs and decided to test the following settings listed below.
I ran Prime for 4 hours and it was stable i could run more but not sure if that is needed.
idle temps are 38-42 on a long day of using my pc and 76C on the Prime run.
-So how are m voltages? are they a bit too high or should i keep them like this?
-I used Artic silver 5 instead of the thermalpaste you get with Noctua nh-d14.
was this a good choise? or are the temps a bit too high?
-Would anny of you advice to go to 3,8Ghz to increase the live span of my cpu? or as asked above are these temps and voltages low enough?
Specs:
Antec 1200
Asus P6X58D-E (Bios version 0405)
Intel core i7 930 2,88Ghz @ 4,01Ghz
Noctua NH-D14
Corsair Dominator GT CMT6GX3M3A 7-7-7-20 3x2GB
Nvidia Geforce 9200 LE (9800 GX2 broken so im currently using this till i get my gtx 560 next month)
Superflower 750 Watt PSU
Windows 7 Ultimate 64bit
OC settings:
Ai Overclock Tuner.....................[Manual]
CPU Ratio Setting......................[21.0]
Intel(r) SpeedStep(tm) Tech............[Disabled]
Xtreme Phase Full Power Mode...........[Enabled]
BCLK Frequency.........................[191]
PCIE Frequency.........................[100]
DRAM Frequency.........................[DDR3-1531MHz]
UCLK Frequency.........................[3063MHz]
QPI Link Data Rate.....................[Auto]
CPU Voltage Control....................[Manual]
CPU Voltage............................[1.23125]
CPU PLL Voltage........................[1.80]
QPI/DRAM Core Voltage..................[1.21875]
IOH Voltage............................[1.14]
IOH PCIE Voltage.......................[1.50]
ICH Voltage............................[1.20]
ICH PCIE Voltage.......................[1.50]
DRAM Bus Voltage.......................[1.64]
DRAM DATA REF Voltage on CHA...........[Auto]
DRAM CTRL REF Voltage on CHA...........[Auto]
DRAM DATA REF Voltage on CHB...........[Auto]
DRAM CTRL REF Voltage on CHB...........[Auto]
DRAM DATA REF Voltage on CHC...........[Auto]
DRAM CTRL REF Voltage on CHC...........[Auto]
Load-Line Calibration..................[Enabled]
CPU Differential Amplitude.............[800mV]
CPU Clock Skew.........................[Delay 300ps]
CPU Spread Spectrum....................[Disabled]
IOH Clock Skew.........................[Auto]
PCIE Spread Spectrum...................[Disabled]
C1E Support............................[Disabled]
Hardware Prefetcher....................[Enabled]
Adjacent Cache Line Prefetch...........[Enabled]
Intel(r) Virtualization Tech...........[Disabled]
CPU TM Function........................[Enabled]
Execute Disable Bit....................[Enabled]
Intel(r) HT Technology.................[Enabled]
Active Processor Cores.................[All]
A20M...................................[Disabled]
Intel(r) SpeedStep(tm) Tech............[Disabled]
Intel(r) C-STATE Tech..................[Disabled]
