Notices

Overclockers Forums > Hardware > General Hardware
General Hardware Discuss your new build and gather upgrade suggestions. And if your question doesn't fit anywhere else...it goes here.
Forum Jump

UDMA 100 seriell ata

Post Reply New Thread Subscribe Search this Thread
 
 
Thread Tools
Old 04-21-02, 04:15 AM Thread Starter   #1
A380
Member



Join Date: Apr 2002

10 Year Badge
 
UDMA 100 seriell ata


-----

Last edited by A380; 11-23-13 at 12:13 PM.
A380 is offline   QUOTE Thanks
Old 04-21-02, 07:41 AM   #2
cw823
Honeybadger Moderator

 
cw823's Avatar 

Join Date: Dec 2000
Location: Earth

10 Year Badge
 
Re: UDMA 100 seriell ata


Quote:
Originally posted by A380
Hi

When connecting udma100 drives with udma100 cabel, do i have to look for sth.
what i mean is the black and the blue plug. is there a difference?
master/slave?

how about seriell ata? should i wait until it is out, befor setting up a new pc?

THX
A380

1) If you only have one drive, connect the blue end to mobo, and the OTHER end to the drive.....leaving the (gray) middle connector unused. Master is always the last drive on the chain.

2) No matter what you do now...hard drive, processor, mem....in 6 months they'll have faster and/or greater out......your decision.

__________________
I can explain it to you, but I cannot understand it for you

honeybadger moderator smacks the **** out of people that cause issues in the classified section

Heatware: cw823
Paypal: paypal @ cw823 dot com

Adak - My spreader bar was shaped using a pair of vise grips, a hammer, and the tow receiver on my pick up

Support your forum:
http://www.newegg.com/
cw823 is offline Benching Profile Folding Profile Heatware Profile   QUOTE Thanks
Old 04-21-02, 08:18 AM Thread Starter   #3
A380
Member



Join Date: Apr 2002

10 Year Badge
 
-----

Last edited by A380; 11-23-13 at 12:13 PM.
A380 is offline   QUOTE Thanks
Old 04-21-02, 11:02 AM   #4
cw823
Honeybadger Moderator

 
cw823's Avatar 

Join Date: Dec 2000
Location: Earth

10 Year Badge
 
Yeppers

__________________
I can explain it to you, but I cannot understand it for you

honeybadger moderator smacks the **** out of people that cause issues in the classified section

Heatware: cw823
Paypal: paypal @ cw823 dot com

Adak - My spreader bar was shaped using a pair of vise grips, a hammer, and the tow receiver on my pick up

Support your forum:
http://www.newegg.com/
cw823 is offline Benching Profile Folding Profile Heatware Profile   QUOTE Thanks

Post Reply New Thread Subscribe


Overclockers Forums > Hardware > General Hardware
General Hardware Discuss your new build and gather upgrade suggestions. And if your question doesn't fit anywhere else...it goes here.
Forum Jump

Thread Tools Search this Thread
Search this Thread:

Advanced Search


Mobile Skin
All times are GMT -5. The time now is 07:07 AM.
Powered by vBulletin® Version 3.8.7
Copyright ©2000 - 2014, vBulletin Solutions, Inc.
You can add these icons by updating your profile information to include your Heatware ID, Benching Profile ID or your Folding/SETI profile ID. Edit your profile!
X

Welcome to Overclockers.com

Create your username to jump into the discussion!

New members like you have made this the best community on the Internet since 1998!


(4 digit year)

Why Join Us?

  • Share experience
  • Max out your hardware
  • Best forum members anywhere
  • Customized forum experience

Already a member?