2500K Voltage Problems/Questions (Help!)

[IBDustin15]

So I got my chip at 4.5GHz and it is extremely stable. I ran 20 runs on Intel Burn Test on Maximum (71 C Max Temp), and also about 17 hours of Prime 95 (60 C Max Temp).

I am however worried about my Voltage. I am seeing people getting 4.5GHz with less than 3.300 VCore. Mine is obviously much higher.

Here is my BIOS & a screen shot my voltage on Prime 95 Burn:

\MB - ( M.I.T )/
\Advanced Frequency Settings/

CPU CLOCK - 33X
BCLK - ( DISABLED ) left at default 100mhz
EXTREME MEMORY PROFILE XMP - ( PROFILE 1 )
SYSTEM MEMORY MULTI - ( AUTO )

\Advanced Cpu Core Features/

CPU CLOCK RATIO [33X]
PWN FREQUENCY CONTROL [ AUTO ]
INTERNAL CPU OVER CURRENT PROTECTION [ AUTO ]
INTERNAL CPU PLL OVERVOLT [ ENABLED ]
RATIO CHANGES IN OS [ DISABLED ]
INTEL BOOST TECH [ ENABLED ]
RATIO 1 - 4 [ 45 ]
TURBO POWER LIMIT [ 300 ]
CORE CURRENT [ 300 ]
CPU CORES ENABLED [ ALL ]
CPU ENHANCED HALT C1E [ AUTO ]
C3/C6 STATE SUPPORT [ AUTO ]
CPU THERMAL MONITOR [ DISABLED ]
BI-DIRECTIONAL PROCHOT [ AUTO ]

\Advanced Memory/

EXTREME MEMORY PROFILE X.M.P [ PROFILE 1 ]
SYSTEM MEMORY MULTI SPD [ AUTO ]
PERFORMANCE ENHANCE [ STANDARD ]
DRAM TIMING SELECT SPD [ AUTO ]
CHANNEL A - B [ AUTO ]

\Advanced Voltage Settings/
MULTI-STEPS LOAD-LINE [ LEVEL 6 ]
CPU VCORE [ 1.365V ]
QPI/VTT VOLTAGE 1.050V [ 1.20v ]
SYSTEM AGENT VOLTAGE 0.920V [ AUTO ]
DYNAMIC VCORE [ AUTO ]
GRAPHICS DVID [ AUTO ]
CPU PLL VOLTAGE 1.800V [ 1.800V ]
DRAM VOLTAGE 1.500V [ 1.500v ]
DRAM VREF 0.750V [ AUTO ]
DRAM TERMINATION 0.750V [ AUTO ]
CH-A/B ATA VREF 0.750V [ AUTO ]
CH-A/B ADDRESS VREF [ AUTO ]

\Misc Settings/

ISOCHRONOUS SUPPORT [ ENABLED ]
VIRTUALIZATION TECH [ ENABLED ]

\Advanced Bios Settings/

QUICK BOOT - [ DISABLED ]
BOOT LOGO - [ DISABLED ]

\Power Management/

HPET SUPPORT [ ENABLED ]
HPET MODE [ 64BIT ] - 64bit windows versions

\Pc Health/

CPU SMART FAN CONTROL [ DISABLED ]

System Model: Z68XP-UD3P
BIOS: Award Modular BIOS v6.00PG
Processor: Intel(R) Core(TM) i5-2500K CPU @ 3.30GHz (4 CPUs), ~3.6GHz
Memory: 8192MB RAM G.SKILL Sniper Low Voltage Series 8GB (2 x 4GB) 240-Pin DDR3 SDRAM DDR3 1600 (PC3 12800)

Here are my results with my CPU on Prime95 burn test and 100% stable. Can anyone give me some help on how I can get to a lower Voltage?

 

[Ajay57]

From my point of view OP not all CPU Chips are the same, if you have that stable and working fine then don't worry about it. If you care to look in my SIG its more or less the same as yours. Whats important here is a stable working system with good Temps. AJ.


p.s. C3/C6 STATE SUPPORT to Disable!