How-To: 8 GHz on Bulldozer

These are full instructions for how to go after CPU Frequency World Records on Bulldozer. This is a cleaned up and prettier version of my original Bulldozer overclocking instructions published on the forums, so I suggest you become a forum member to follow the bleeding edge developments that go on regularly there.

Hopefully this will be helpful for anyone out there with Bulldozer and Liquid Nitrogen, and for everyone else I hope it uncovers the secrets of how its done. It worked for me to the tune of 8.06GHz and currently 17th place in the world (Update: Improved to 8.235GHz 4th place in the world). Why share the secrets? I only know this because of what Overclockers Forums has taught me over the years, and this site was founded on sharing our experience – its what inspired me to start in this overclocking hobby.

A banner for my home, hanging in my garage
A banner for my home, hanging in my garage

I go after records like this with intent to kill something, but if you somehow don’t kill anything doing this, please don’t blame me that everything survived. I learned this from Phenom II experience: AMD 965 BE @ 6.861 GHz, AMD 975 BE @ 7.035 GHz, and AMD 980 BE @ 7.002 GHz. On Bulldozer, I’ve bought 2 CPUs so far: an FX-6100 @ 7.744 GHz and an FX-8120 @ 8.060 GHz. I also was observing at AMD in Austin while Chew* and Macci were breaking the world record earlier this year. At the request of AMD, I provided independent “expert testimony” on what I saw when they applied for the Guinness book of World Records.

Going for 8 GHz
Going for 8 GHz

This is not hard however this article is a bit long because I have spelled out very specifically what to do. Refer to the headings below if you’d like to skip to the part you are looking for. Ask in the comments if you have any questions. Keep in mind everything below was done at -190C/-374F at the base of my cooler. If you attempt this on air or water cooling please post including pictures and video. I’ll write your name in the “good” column in my journal if it catches fire.

Table of Contents


Download PSCheck 3.4.1This is where people typically make ominous statements about things being potentially dangerous. I have read where other people have said PSCheck could kill your chip, but I’m not going to say that myself – it is a tool and I haven’t killed anything with it yet.

BIOS that allows disabling on a per core basis, not only per module. For the Asus Crosshair V Formula, BIOS 9920 did the trick for me.

BIOS Settings

In bios disable everything for power management including throttling. When you load windows you should start with a consistent CPU frequency in CPUz. If its fluctuating go back to BIOS to disable the right stuff.

If your motherboard and BIOS has the ability to disable on a per core basis, turn one core on in two different modules. You need one core per module so that you can change frequency of each core independently. On bulldozer you cannot change frequency independently for cores within the same module. If you are overclocking both cores and not only one you will have a harder time hitting higher frequencies.

Using PSCheck

PSCheck allows you to set multipliers on a per core basis. This is important as you will be running 2 cores for CPUz. One core will be idling at a safe frequency while the other will be maxed out for CPUz validation. For this example, we will be overclocking core 0 and this is how to use PSCheck:

  1. In PSCheck, go to File>Settings and select the PState Configuration tab. Place a check next to “all” in the left side panel to select all cores. On the right side panel, deselect the enable checkbox for Pstate Pb0 and Pstate Pb1. Then select the Boost Configuration tab and place a check next to “cpbdis” (disable cpb) near the top. Finally, click Save CPUs and Exit. This ensures you get consistent frequencies from your PSCheck settings, without any throttling or jumping around to cause instability.
  2. Go back to File>Settings and select the Pstate Configuration tab. On the right hand panel in the “Pstate P0” row, select your desired multiplier setting under the CPUFID column. To know what multiplier setting you want, look at the frequency column to the right after you choose a setting – the value in the frequency column divided by 200 is the multiplier that will be set. Once you have the multiplier you want, save cpus and exit. Ignore all other columns/settings. This saves the multiplier setting, but IT DOES NOT APPLY IT YET.
  3. To apply the multiplier setting you selected, on the main PSCheck window under “Processor Performance States” there should be two columns labeled 0 and 1, for each core you have enabled. In order for your multiplier to be applied, you must toggle the setting for core 0 from Pstate P0 to Pstate P1, then back to Pstate P0.

Finding Max Frequency

  1. Ensure CPU-NB does not limit you: Set CPU-NB in BIOS to a relatively low multiplier, as its frequency will increase when you raise FSB. Run generous volts. I like to keep CPU-NB between 2600-4000MHz when FSB is increased, and I run 1.5-1.6V when going for max frequency. Extra CPU-NB volts may help when more vcore does not; it helped me validate 7GHz on Phenom II. I haven’t found if it definitely helps on Bulldozer however.
  2. Ensure HTLink does not limit you: Set HT Link in BIOS to a relatively low multiplier, as its frequency will increase when you raise FSB. I like to keep HT Link between 1800-2800MHz when FSB is increased.
  3. Ensure RAM does not limit you: Set RAM multiplier as low as possible. I used 1066. Loosen timings, run generous volts.
  4. Max CPU Multiplier: Set vcore to 1.8V, set CPU-NB to 1.5V, then using PSCheck Set CPU Multi to the maximum setting it can do. For Bulldozer this was 31.5, which meant I started out at 6300MHz. If you have done everything right so far, these settings should get you comfortably into the 7 GHz.
  5. Max FSB: Start at a frequency of 7000/multiplier (7000/31.5 = ~220MHz). Increase FSB in increments of 5Mhz, until it crashes – this is quicker if you have a good software tool like TurboV or ROG Connect. Once it crashes, increase vcore by .05 or .1 (what you are comfortable with), then try to max FSB again, going in 1MHz increments once you get close to the frequency you crashed at before. Once you crash again, either increase vcore again or move on to the next step.
  6. Reduce Multi by .5, Max FSB: Same as before, but your FSB will be higher this time. See if you improve your CPU frequency using this slightly lower multiplier.
  7. Repeat step 6 as necessary. During the last few steps, tweak voltage settings as desired to get the last drop.

Conclusion and Final Notes

That’s how I got the highest CPU Frequency score on, and the 17th highest in the world. Now come and get me!

Here are some parting notes which may help also:

  • I went from 1.8V to 2.1V on vcore. On the FX-6100, from 1.9-2.1V was just making sure I couldn’t get any more out of it on multis between 30-31.5. My highest frequency was 7744MHz at 1.872 vcore. On the FX-8120, 2V ended up helping on that chip. Testing for the limits of your particular chip is the only way to be sure you have maxed it out.
  • I only maxed one core, the other core sat at a comfy/stable 5-6GHz. All other cores were disabled in BIOS.
  • You may read elsewhere that PSCheck can kill your CPU if you use certain cores or modules or whatever. I don’t believe that is true. I do believe that sometimes chips just randomly die when you are putting 1.8-2.2V through them. But PSCheck could have bugs that make sea-pea-uze asplode, dunno as I haven’t experienced them in my overclocking.
Have fun and good luck!

Gratuitous Frosty Pic
Gratuitous Frosty Pic

My rig after hitting 8 GHz
My rig after hitting 8 GHz
About Matt Bidinger 60 Articles
My name is Matt Bidinger. I manage the editorial and forum staff for, and I enjoy Community Management with a number of large internet sites. I've worked in IT in my professional career; my site involvement keeps me off the streets at night. When relaxing, I can usually be found walking the parks and roads of Rootstown, OH with my wife Kim and my dog Bubba.

Loading new replies...

Avatar of David

Forums Super Moderator

15,810 messages 11 likes

Nice! Cheers Matt :thup:

Reply Like

Avatar of Brolloks

Benching Senior on Siesta, Premium Member #8

7,523 messages 7 likes

A big CONGRATS to you Matt:clap:, that is an accomplishment to be proud of, I sure am gald you are on our benching team:salute:

I just love your frosty pics, looks like a winter wonderland in the world of benching :)

Reply Like

Avatar of hokiealumnus

Water Cooled Moderator

16,561 messages 25 likes

Posted this at the bot and XS. Couldn't resist. Well done! :)

Reply Like

Avatar of 'Cuda340

Very Welcoming Senior, Premium Member #11

2,853 messages 0 likes

Nice write up :cool:

Reply Like

Avatar of I.M.O.G.

Glorious Leader

25,037 messages 4 likes

Thanks guys. Its everything a person needs to know, after this, it's just a matter of finding the right chip.

Reply Like

Avatar of IJAHman


166 messages 0 likes

This is crazy but awesome! 8ghz!!! men that's wow! :clap: Congrats & Cheers!

Reply Like

Avatar of kskwerl


535 messages 0 likes

17th in the world! That's nasty!:salute:

Reply Like

Avatar of I.M.O.G.

Glorious Leader

25,037 messages 4 likes

Thanks, 13th now with 8.123GHz:

Still working on it, but thats the best I could do with a couple more hours spent working on it last night. :)

Reply Like

Avatar of Douken


1,763 messages 0 likes

Very nice indeed

Reply Like

Avatar of Mantis187


52 messages 0 likes

i got a ? what is the point in doing this xtreme overclock? just bragging rights im assuming is there anyway that anyone will actually use the comp like that for the whole time they got it? this is not a flame im just wondering. and what does it cost to get that stuff

Reply Like