After some other information I now have a stable 3.6ghz e6850 that is Prime95 tested at both 12, and 24 hours, cleared, error free.
Now to take it to the next step, or so I hope.
Currently these are my settings under CPU-Z:
CPU: 3.608ghz
Multi: x8
FSB: 451
Rated FSB: 1804.2
Dram Freq: 902.1
FSBRAM: 1:2
Clock: 9-9-9-24
Com Raate: 1T
Temps are as follows at Idle:
MOBO: 27c
CPU:26c
Core1: 32c
Core2: 23c
NB: 32c
SB: 28c
Temps are as follows at Load:
MOBO: 27c
CPU: 41c
Core1: 50c
Core2: 41c
NB: 34c
SB: 29c
Voltage:
CPUv: 1.42
CPU PLLv: 1.60
NBv: 1.49
DRAMv: 1.90
FSBTermv: 1.36
SBv: 1.125
CPU GTL Ref: .63x
NB GTL Ref: .67x
Now tonight I plan to start testing and run Prime95 with the setting on the FSB up'ed to 465 while dropping the CPU voltage to 1.38 or so. Would this be the ideal way in trying to pump out some more ghz, or am I still running down the wrong road ? This is my first experience with OC'ing and first experience building a comp!
At FSB 465 if I can run for 6-10 hours stable I would like to bump it up some more but currently im trying to take it slow and one step at a time to allow the CPU to get used to running under the new settings.
Any guidance would be very much appriciated and welcome!
Thanks in advance,
Kevin
[Comp Specs]
Asus Maximus Extreme MOBO
OCz 1600 DDR3 2gig currently
Thermaltake 1k PSU
Water cooled (CPU and NB are both being cooled by the setup that came in the Thermaltake Swordm Case, not the best, but soon to be replaced by the Koolance CPU-330 CPU Block, 2x Koolance VR-AS40 Voltage Reg Blocks, Koolance CHC-120 NB Block, and running this loop the Koolance EXOS-2 LX)
Now to take it to the next step, or so I hope.
Currently these are my settings under CPU-Z:
CPU: 3.608ghz
Multi: x8
FSB: 451
Rated FSB: 1804.2
Dram Freq: 902.1
FSBRAM: 1:2
Clock: 9-9-9-24
Com Raate: 1T
Temps are as follows at Idle:
MOBO: 27c
CPU:26c
Core1: 32c
Core2: 23c
NB: 32c
SB: 28c
Temps are as follows at Load:
MOBO: 27c
CPU: 41c
Core1: 50c
Core2: 41c
NB: 34c
SB: 29c
Voltage:
CPUv: 1.42
CPU PLLv: 1.60
NBv: 1.49
DRAMv: 1.90
FSBTermv: 1.36
SBv: 1.125
CPU GTL Ref: .63x
NB GTL Ref: .67x
Now tonight I plan to start testing and run Prime95 with the setting on the FSB up'ed to 465 while dropping the CPU voltage to 1.38 or so. Would this be the ideal way in trying to pump out some more ghz, or am I still running down the wrong road ? This is my first experience with OC'ing and first experience building a comp!
At FSB 465 if I can run for 6-10 hours stable I would like to bump it up some more but currently im trying to take it slow and one step at a time to allow the CPU to get used to running under the new settings.
Any guidance would be very much appriciated and welcome!
Thanks in advance,
Kevin
[Comp Specs]
Asus Maximus Extreme MOBO
OCz 1600 DDR3 2gig currently
Thermaltake 1k PSU
Water cooled (CPU and NB are both being cooled by the setup that came in the Thermaltake Swordm Case, not the best, but soon to be replaced by the Koolance CPU-330 CPU Block, 2x Koolance VR-AS40 Voltage Reg Blocks, Koolance CHC-120 NB Block, and running this loop the Koolance EXOS-2 LX)