Just tweaked that little bit more from my Q6600

Rizo-uk · Jan 4, 2010

Just been playing again and tightened my ram timmings and my core voltage has been upped still running good temps too with the vapochill mirco.

Sat at 3.37ghz, cant get the fsb above 380 no matter what voltage/settings i use

Limitation on the mobo i think then? P5K

MIAHALLEN · Jan 7, 2010

Normally that CPU/board doesn't have a limit that low??? :shrug:

We need more info to help out...specifics man

redduc900 · Jan 7, 2010

Here's a BIOS template for the P5K that you can fill out showing all of your current settings (disregard the settings in the template, and replace w/ your own)...

Code:

[B]JumperFree Configuration Settings[/B]
AI Overclocking: Manual
CPU Ratio Control: Manual
- Ratio CMOS Setting: 9
FSB Frequency: 266
PCI-E Frequency: 100
DRAM Frequency: AUTO 
DRAM Timing Control: Manual
CAS# Latency: 4
RAS# to CAS# Delay: 4
RAS# Precharge: 4
RAS# Activate to Precharge: 12
TWR: AUTO
TRFC: AUTO
TWTR: AUTO
TRRD: AUTO
TRTP: AUTO
DRAM Static Read Control: Disabled

Transaction Booster: AUTO
Boost Level:
Clock Over-Charging Mode: AUTO

CPU Spread Spectrum: Disabled
PCIE Spread Spectrum: Disabled

CPU Voltage: AUTO
CPU Voltage Reference: AUTO
CPU Voltage Damper: AUTO
CPU PLL Voltage: AUTO
DRAM Voltage: 2.10
FSB Termination Voltage: AUTO
North Bridge Voltage: AUTO
North Bridge Voltage Reference: AUTO
South Bridge Voltage: AUTO

[B]Advance CPU Settings[/B]
CPU Ratio Control: Manual
- Ratio CMOS Setting: 9
C1E Suppport: Disabaled
Max CPUID Value Limit: Disabaled
Vanderpool Technology: Disabaled
CPU TM Function: Disabaled
Execute Disable Bit: Disabaled
PECI: Enabled

[B]USB Configuration[/B]
USB Functions: Enabled
Legacy USB Support: Disabled

bda1967 · Jan 7, 2010

I was running a Q6600 G0 on a P5K MB over a year ago and I saved my OC settings. I'll post them when I get home from work.

Rizo-uk · Jan 7, 2010

bda1967 said:
I was running a Q6600 G0 on a P5K MB over a year ago and I saved my OC settings. I'll post them when I get home from work.

if you can mate that would be very very good of you... what should i be getting it upto then?

bda1967 · Jan 7, 2010

I only got stable to 3.6GHz and then I stopped so here are my settings.

SPEED GHz
FSB FREQ -450
CPU RATIO - 8
CPU VOLT. - 1.375 (My vid was 1.263v)
CPU PLL VOLT. - 1.7v
FSB VOLT. - 1.5v
DRAM VOLT. - 2.1 (DDR2-1000)
NB VOLT. REF. - 1.7v
CLOCK OVERCHARGE - 1
DRAM COM. RATE - 2N
LOAD LINE CALIBRATION - ENABLED
CPU GTL VOLT. REF. - .63x
NB VOLT. REF. - .67x
CPU SPREAD - DISABLED
RAM - PC2-8000
RAM FREQ - 900MHz
FSB:RAM - 1:1
CAS# LAT. - 5
RAS# TO CAS# DELAY - 5
RAS# PRE TIME - 5
RAS# ACT - 15
C1E SUPP. - DISABLED
CPU TM - ENABLED
VANDERPOOL - DISABLED
EXEC. DISABLE BIT - ENABLED
MAX CPUID VAL. -DISABLED
PCI EXPRESS - 100
FSB STRAP TO NB MHz - 400

NOTE: I used different RAM. Since you are using DDR2-800 you won't be able to use my RAM settings, unless your RAM overclocks really well and you loosen the timings. You might have to use the 9 multiplier with a lower FSB instead of the 8.

Hope that helps.

Just tweaked that little bit more from my Q6600

Rizo-uk

Member

MIAHALLEN

Senior Member

redduc900

Inactive Moderator

bda1967

Member

Rizo-uk

Member

bda1967

Member

Similar threads