I haven't seen any posts on Hagen powerheads?
Any user experience?
Mine is aprox. 15 years old, I dunno what model it is.... doh
I did the bucket test: 400+ gph. I think mine pushes 50cm of head... ? nearest I could match.
This is my first time.... so be gentle!
I tested it in a closed loop: res/pump/res: 100+ deg. f (yikes)
5/8 ID tubing fit right on pump outlet, then back into res. for the loop test
I epoxied a 2" to 1 1/4" pvc pipe to pumps inlet, threaded into
water tite junction box. Put 2 odd size bulkhead fittings into
top of res. between 1/2" and 5/8" methinks. one for return
the other for fill.
Heatercore from Toyoto Corolla 1200 (Denso) 5/8" in/outlets
My buddy tore-off one while pulling through firewall.
Epoxied 1/2" brass barb in it's place.
5/8" pump to 5/8" HC inlet is sweet, no fussing.
2-YL 120mm fans 64cfm-2000rpm-32dba (not powerful but quiet)
Test with: fans/shroud/heatercore: 70 deg. f (matches ambient)
(Pump is the only heatload) I got's no blocks!
Uber-Ghetto
Dremeled HC finned size slot into top of case for air extraction.
HC takes the 1st CD slot, 2 middle slots will be used for air-intake Burner will be on the bottom.
Cardboard is used right now, to seal air vent from inside of case.
I want to use 3 blocks in series. Cpu->Gpu->SB (NB too?)
I hope the pump/setup will have enough oomph for this.
DTWW, DD9700, DTNB.
Gonna tear it all apart to mount things properly, and I have 1/2"
Clearflex for final install.
What do ya think?
Any user experience?
Mine is aprox. 15 years old, I dunno what model it is.... doh
I did the bucket test: 400+ gph. I think mine pushes 50cm of head... ? nearest I could match.
This is my first time.... so be gentle!
I tested it in a closed loop: res/pump/res: 100+ deg. f (yikes)
5/8 ID tubing fit right on pump outlet, then back into res. for the loop test
I epoxied a 2" to 1 1/4" pvc pipe to pumps inlet, threaded into
water tite junction box. Put 2 odd size bulkhead fittings into
top of res. between 1/2" and 5/8" methinks. one for return
the other for fill.
Heatercore from Toyoto Corolla 1200 (Denso) 5/8" in/outlets
My buddy tore-off one while pulling through firewall.
Epoxied 1/2" brass barb in it's place.
5/8" pump to 5/8" HC inlet is sweet, no fussing.
2-YL 120mm fans 64cfm-2000rpm-32dba (not powerful but quiet)
Test with: fans/shroud/heatercore: 70 deg. f (matches ambient)
(Pump is the only heatload) I got's no blocks!
Uber-Ghetto
Dremeled HC finned size slot into top of case for air extraction.
HC takes the 1st CD slot, 2 middle slots will be used for air-intake Burner will be on the bottom.
Cardboard is used right now, to seal air vent from inside of case.
I want to use 3 blocks in series. Cpu->Gpu->SB (NB too?)
I hope the pump/setup will have enough oomph for this.
DTWW, DD9700, DTNB.
Gonna tear it all apart to mount things properly, and I have 1/2"
Clearflex for final install.
What do ya think?