How to connect x2 AQUA COMPUTER D5 Pump Modules with RPM Signal

[Zgiera]

Hi there, I have a question which is
I have AQUAERO 6XT fan controller and 2 POWERADJUSTMENTS 3 ULTRA
Poweradjustment no.2 is connected to Poweradjustment no.1 and PA no.1 is connected to high speed port on AQUAERO 6XT

so I'm wonder myself how to connect x2 AQUA COMPUTER D5 Pump Modules with RPM Signal in the best way
as far as I know I can connect 1 water pump to hihg speed port on AQUAERO 6XT via Y cable connector which I did but water pump won't work

and is any chance to control RPM of this water pump with Aquaero 6xt?

Many thanks at advance for any help

 

[GTXJackBauer]

Your best bet is to head over to their forums and ask this same question. It can take them a while to hear from but once they do respond, they should give you the answers you're looking for. I wouldn't guess on anything at this point on such a premium priced product as I would just rather hear it from them or someone here who's done it already.

Hope it all works out and let us know the outcome.

 

[Zgiera]

These 2 water pumps would work with fan connectors on Aquaero 6XT as fans but all connectors are busy with fans which I have on my PC case. Also I was advised to connect one of these pumps to high speed port but it won't work either.

I have posted some questions on Aquacomputer forum and still waiting for reply. Will let you know when I get reply from them.

 

[GTXJackBauer]

I have posted some questions on Aquacomputer forum and still waiting for reply. Will let you know when I get reply from them.

Awesome. Please do because a lot of things are sketchy when it comes to configuring or getting help from them. Its always good to know what works and what doesn't.

I thought about purchasing one but wished I had not already purchased my pumps and flow meter otherwise it would have been all aqua for compatibility on the AQ.

Regardless, their maiden language is German so its hard getting a answer right away. Wish this product was much easier to use without doing any modding, etc.

 

[Zgiera]

there is resolve of my problems with AQUA COMPUTER D5 pump modules with RPM signal
http://shop.aquacomputer.de/product_info.php?products_id=2750
which is
you can't connect AQUAERO aquabus high speed port to any water pump without aquabus interface becasue
AQUAERO via aquabus high speed or low speed port can't recognise device before you manualy setup ID number device in the system
tab of the device.
Unfortunately that pump which I purchased has no USB interface at the back due to it was bought with purpose to set up in
BITSPOWER D5 Mod Kit (BP-D5MA-MBK)
https://www.caseking.de/bitspower-d5-mod-kit-schwarz-wapu-091.html?campaign=psm/geizhals
and
BITSPOWER D5 Mod Top S-Model G1/4 – Acetal
https://www.caseking.de/en/bitspower-d5-mod-top-s-model-g1-4-zoll-acetal-waau-341.html

waterpump D5 with aquabus its to big (becasue of their interface at the back) to be mounted in that mod kit
http://shop.aquacomputer.de/product_info.php?products_id=2901

so there is only one way to connect this D5 water pump to aquaero or poweradjustment only via fan connector (only one water pump per fan channel!!)
there is a cable available to allows you connect waterump with aquaero or poweradjustment via fan connector
http://shop.aquacomputer.de/product_info.php?products_id=2345

Problem with this conenction is there is no wide range of RPM for pump so after tests which I made the pump start working at 50 procent of RPM usage when the red dot
at the back of water pump was set up at 5 level of speed

The best solution to this kind of connection with PWM input and speed signal is different water pump D5
Aqua Computer D5 pump motor with PWM input and speed signal
http://shop.aquacomputer.de/product_info.php?language=en&products_id=3255
and can be mounted in BITSPOWER Mod kits as well

Regards