help with OC q9650

[capie]

Hi do need help with my overclock.
I have tried to get my PC stable ad 3800 Ghz. The test’s that I run prime95 14 hrs and 10 hrs blend are =OK, Memtest 7 hrs 10 passes =OK, Intelburn 10 runs “high” = OK. OCCT 1 hr large data= OK , Buth when I run FSX my system reboots. I don’t know if FSX beeing on a different drive (SSD) is the problem?
Hope some one can help me solve this and get my system stable.

This are my settings:

CPU Level Up = Auto
Memory Level Up = Auto
AI Overclock Tuner = Manual
CPU Multiplier = 9.0
FSB - Memory Clock Mode = LINKED
FSB - Memory Ratio = SYNCED
FSB (QDR) MHz = 1690 = (423) MHz = 3600
MEM (DDR) MHz = 1690
LDT Frequency = 5x
PCIE Bus Slot 1 & 2 MHz = 100
PCIE Bus Slot 3 MHz = 100
SPP<->MCP Ref Clock, MHz = Auto
SLI-Ready Memory = Disabled


Memory Timing Setting
P1 = enabled
P2 = enabled
tCL ( CAS Latency ) = 9
tRCD = 9
tRP = 9
tRAS = 24
Command Per Clock (CMD) = 2T
tRRD = auto
tRC = 34
tWR = auto
tWTR = auto
tFAW = auto
tRD = auto
tRTP = auto
tRFC =auto
tREF = auto

Over Voltage
CPU Voltage =1.32500
Loadline Calibration = disabled
CPU PLL Voltage = auto
CPU VTT voltage = auto
Memory Voltage = 1.66
NB Core Voltage = 1.40
SB Core Voltage= 1.50




CPU GTL REF0 Ratio = Auto
CPU GTL REF1 Ratio = Auto
CPU GTL REF2 Ratio = Auto
CPU GTL REF3 Ratio = Auto
NB GTL REF Ratio = Auto
DDR3 CHA1 Ref Volt = Auto
DDR3 CHB1 Ref Volt = Auto
DDR3 CHA2 Ref Volt = Auto
DDR3 CHB2 Ref Volt = Auto

CPU Configuration
CPU Internal Thermal Control =Auto
Limit CPUID MaxVal = Disabled
Enhanced C1 (C1E) = Disabled enabled
CPU C estate Capability = Disabled
Execute Disable Bit = enabled
Virtualization Technology = enabled
Enhanced Intel SpeedStep(tm) enabled
CPU Core 2 = Enabled
CPU Core 3 = Enabled
CPU Core 4 = Enabled

Spread Spectrum Control
CPU Spread Spectrum = Disabled
PCIE Spread Spectrum = Disabled
MCP PCIE Spread Spectrum =Disabled
SATA Spread Spectrum = Disabled
LDT Spread Spectrum = Disabled












AIDA64 readings
VOLTAGE BIOS set FSX OCCT
CPU core 1.32500 1.344 1.312
VTT auto 1.216 1.216
PLL auto 1.520 1.520
NB 1.40 1.424 1.424
SB 1.50 1.488 1.488
DIMM 1.66 1.696 1.696

regards,
Capie

 

[redduc900]

Post your complete system spec's, including MB, RAM; including quantity, etc. In the meantime disable EIST, C1E, and C-States. Also enable LLC, and instead of a 1:2 DRAM divider at a FSB of 423MHz = DDR3-1690, try a lower FSB : DRAM ratio = a lower effective DRAM frequency.

 

[capie]

Whow that was fast.
My specs are:
striker II extreme,
cpu: q9650
Ram: CMG4GX3M2B1600C7 V 1.5 – 1.65 (2 x 2GB) corsair
PSU: Ultra X4 850W
HDD : WD 1500HLFS
Cooling: corsair H100
Sound Card : Supreme FX II .
Win7 64 bit, home premium

and i will try your advise.
FSB memory ratio I have 5:4 or 3:2. any suggestions?

thanks!!!
regards,
capie

 

[Cigarsmoker]

Maybe I'm read the OP wrong. But he run Prime 95 for 10+ hours and he's stable. But crashes when he tries to run a program off the SSD. I'm thinking the problem is not the OC but the SSD.

 

[capie]

Hi me again,
I did as You suggested, also increased The Vcore to 1.33750 which is (maybe) still to low because ADIA64 gives me 1.39... most of the time?
I did used FSX today without any problems. But trying to run a (SSD)diagnostic scan i had a reboot and after that a massage that i need to contact the
re seller or manufacturer. So it seems that there is also a problem with the SSD.
regards,
capie

 

[Cigarsmoker]

What make and model of SSD? Are you suffering the infamous BSOD problem with Sandforce controlled SSD? If so I can sympathize.

 

[capie]

Hi and thanks.
I do have a Intel SSD X52M 80 GB drive. After using the trim tool the error message went away. I do have BSOD but some times also just a reboot.
FSX is the only program running on that drive. I'm doing some more testing to check it. I do also have a question about AIDA64. What to do with the readings. exp my bios Vcore = 1.33750 and AIDA64 shows 1.392. How serious is that and use AIDA64 readings as a guide line or not?
regards,
capie

 

[capie]

Hi, it's some time now. did some flights(FSX) in the last week, and ( still crossing my fingers) had no crashes so far. Looks like ( at least i hope so)problem is fixed.
Just to let U know. I mean. It's nice when U have a problem and people help that U let them know how things are going OK!!!
thanks and regards,
capie