Fitting for two GPU's with no space

[kielerrr]

I'm sure this question has been asked but I've spent hours looking for an answer and can not find the solution..

I'm trying to connect 3 Titan Hydro Coppers but I'm not sure which fitting to go between the top two cards that have no space between them. I've looked everywhere and it seems every fitting is for cards that have space.. I'm on an ASUS Rampage IV Extreme and I'm trying to find the fittings for the setup that's:

SLOT1: TITAN
SLOT2: TITAN
SLOT3: EMPTY
SLOT4: TITAN

I think I can figure out which fitting to go between slot 2 and slot 3 (22-31mm fitting?) but I don't know which fitting I need to buy for between slot 1 and slot 2 since im pretty sure there will be no space..

Sorry for such a newb question but I can not find the answer anywhere..

 

[Pierre3400]

Its depends on your fittings choice.

In my case with the blocks i have, and the fittings, i needed 16mm of solid tube.

If you have EK block and fittings, then its longer.

Are you planning solid tubes or normal tube?

 

[Witchdoctor]

I like crystal Link

they make it in different sizes to meet the needs of your particular slot layout

http://www.frozencpu.com/products/1...nk_Tube_Set_-_2_Slot_Spacing_BP-CLTAC-S2.html

 

[kielerrr]

So 16mm fittings will squeeze between the GPU's? Something like this? http://www.frozencpu.com/products/2...ck_Sparkle_BP-BSDG14AALPM.html?tl=g30c101s873

Witch, I saw those but that would require the ports to be on top of the block whereas the ports on the Titan Hydro Coppers are on the side facing eachother..

 

[Pierre3400]

So 16mm fittings will squeeze between the GPU's? Something like this? http://www.frozencpu.com/products/2...ck_Sparkle_BP-BSDG14AALPM.html?tl=g30c101s873

Witch, I saw those but that would require the ports to be on top of the block whereas the ports on the Titan Hydro Coppers are on the side facing eachother..

In my case, but i am running heatkiller blocks and Bitspower mulitlink fittings.

All depends what the blocks allow. All you can do is dry fit. Measure the spacing, and then see where the leaves you. Trust me, you are not the first person to stick hydro coppers close to each other.

EDIT:
This thread should cover you issues.
http://forums.evga.com/tm.aspx?m=1955080

 

[Witchdoctor]

So 16mm fittings will squeeze between the GPU's? Something like this? http://www.frozencpu.com/products/2...ck_Sparkle_BP-BSDG14AALPM.html?tl=g30c101s873

Witch, I saw those but that would require the ports to be on top of the block whereas the ports on the Titan Hydro Coppers are on the side facing eachother..

you can use those slid fitting as well, they simply slid on an O-ring, very nice and less hassel. Crystal link seals on an o-ring on each side, they make dual o-rigng fitting and singels for tight spots. I lke them because the tubing is clear arcylic and won't stain if using dies

 

[kielerrr]

Thanks for the help all.. I ordered the 11mm Swiftecs so got fingers crossed itll work when they get here!

 

[GTXJackBauer]

Yup, I was also thinking of the Swiftech SLI Lok-Seal Fittings. You should be fine with those. I am not sure you'll be able to use those say from slot 2 to slot 4. You might need a longer one. Not sure though.