Kingston pc2700 won't oc' !! edit**
here is my problem
my specs :
athlon xp2000+ locked
abit kx7-333
Enermax 350W PSU
kingston value ram pc2700 512MB with infineon chips (1 stick)
winXP
Asus GeForce4 Ti4600
i have 1cd-rom and a plextor 24x burner both slave to my 2 master hdds
i have 2 pci cards, a sb live5.1 and my NIC (no special brand, it's SURECOM)
I just did an upgrade from 2 256 kingsotn pc2100 to the one above.Before i could go as high as 135 fsb to run have my system running stable at most agressive settings, that is Ultra, Cas 2, 1T
i can raise the Vdim up to 2.85 but i don't see any change.
After getting my new stick i tried to push it but even at 135 it won't load xp, it is restarting after trying to boot the logo.sys(the loading windows image)...
here are my full detailed settings in BIOS. The values in () are the alternatives.
Ratio(FSB:AGPCI) : 4:2:1 (3:2:1, 5:2:1)
CPU fast CMD decode : Ultra (Normal,Fast)
CAS : 2 (2.5)
Bank Interleave : 4 Bank (Disabled, 2 B)
Precharge to Active(Trp) : 2T (3T)
Active To Precharge(Tras) : 5T (6T)
Active to CMD(Trcd) : 2T (3T)
DRam Access : 2T (3T)
DReam Queue Depth : 4 level (2L,3L)
DRam CMD rate : 1T Command (2T)
actually i could raise the fsb up to 138 stable after changing the ratio to 5:2:1 and the highest voltage that is 2.85
should i change the mem from 166 to 133???
plz help!!
here is my problem
my specs :
athlon xp2000+ locked
abit kx7-333
Enermax 350W PSU
kingston value ram pc2700 512MB with infineon chips (1 stick)
winXP
Asus GeForce4 Ti4600
i have 1cd-rom and a plextor 24x burner both slave to my 2 master hdds
i have 2 pci cards, a sb live5.1 and my NIC (no special brand, it's SURECOM)
I just did an upgrade from 2 256 kingsotn pc2100 to the one above.Before i could go as high as 135 fsb to run have my system running stable at most agressive settings, that is Ultra, Cas 2, 1T
i can raise the Vdim up to 2.85 but i don't see any change.
After getting my new stick i tried to push it but even at 135 it won't load xp, it is restarting after trying to boot the logo.sys(the loading windows image)...
here are my full detailed settings in BIOS. The values in () are the alternatives.
Ratio(FSB:AGPCI) : 4:2:1 (3:2:1, 5:2:1)
CPU fast CMD decode : Ultra (Normal,Fast)
CAS : 2 (2.5)
Bank Interleave : 4 Bank (Disabled, 2 B)
Precharge to Active(Trp) : 2T (3T)
Active To Precharge(Tras) : 5T (6T)
Active to CMD(Trcd) : 2T (3T)
DRam Access : 2T (3T)
DReam Queue Depth : 4 level (2L,3L)
DRam CMD rate : 1T Command (2T)
actually i could raise the fsb up to 138 stable after changing the ratio to 5:2:1 and the highest voltage that is 2.85
should i change the mem from 166 to 133???
plz help!!
Last edited: