What is the maximum voltage you use to run your Q6600/Q6700/Q9300/Q9450??

[darkcow]

Processor: q6600 (G0)
Speed: 3600mhz (400x9)
Voltage: 1.45v (Actual, vDroop mods ftw)
Temperature: 45-48c (on a cold day its 37c)
Load program: Prime 95
Cooling: Apogee GT w/ Bow mod, MCR320 with 3 yate loons

 

[ghost_recon88]

Processor: Q9550 E0
Speed: 4105MHz
Voltage: 1.248v
Temperature: 54,54,49,49
Load program: P95 Small FTT
Cooling: Lapped TRUE

 

[freeagent]

^^

nice

edit:

try spinning your true around for more uniform temps

 

[Steven-1979]

there are people out there using 1.9v?

 

[Big Mike]

Probably extreme benchers (ln2, dry ice) that would be using that much, or people who wanted to vote for something rediculous

 

[SuperMotarded]

Processor: Q6600 (1.2625 VID)
Speed: 400x9 (3600mhz)
Voltage: 1.425v bios, 1.375v after droop.
Temperature: 50c loaded
Load program: Prime 95, F@H
Cooling: Swiftech setup. Apogee, MCP655, MCR-220

 

[Priv]

Processor: Q6600
Speed: 3.6 GHz (450x8)
Voltage: 1.368V LLC enabled
Temp: 58C loaded
Load program: Prime 95 small fft
Cooling: TRUE push/pull

 

[=ACID RAIN=]

Q6600
3.6GHz 400x9
1.45v BIOS (~1.38v load)
Load program prime 95
Around 55C. Been a while since I've sat there and worked the CPU over. Also have GPU in loop.
D-Tek fuzion WC

 

[TheBrain]

Processor: Q6600 G0
Speed: 3.6 GHz (450x8)
Voltage: 1.4V
Temp: 60C loaded
Load program: Prime 95(25.8 Small FFT)
Cooling: Zalman 9700LED at almost minimum rpm

 

[Slmhofy]

Processor: Q6600 G0
Speed: 3.6 GHz (400x9, 4,4,4,12)
Voltage: 1.344V
Temp: 40ish idle, 54ish loaded
Load program: Prime 95(25.8 Small FFT)
Cooling: Swiftech MCR320-QP-K

 

[terran2k]

man I simply cannot deal with putting more than 1.4v core on my q6600 in bios, makes in uneasy for some reason. so Im running it at 1.34v @ 3.240Ghz.

360 x 9

 

[freeagent]

heheh 1.4 is ok, once you get to around 1.5 and up she starts to get a bit warm

 

[GandalfGrey]

Processor: Q9550 - VID 1.25v
Speed: 4.0GHz (472x8.5)
Voltage: 1.38 BIOS, 1.365 Reported.
Temperature: 62Avg across cores on Load
Load program: Prime 95
Cooling: Zalman 9700NT

 

[Badbonji]

My dad has my Q9450, and he is using air cooling for a modest 3.2Ghz 1.3Vcore
Vid was around 1.2, max temp around 47-50C

 

[chinky714]

Processor: Q6600 G0
Speed: 3.5GHz 390x9
Voltage: Bios; 1.39V CPUZ; 1.32 during load, 1.37 idle.
Temperature: 51C Load using prime 95 small/large FFT and IBT stress level 2
Cooling: Xigmatek S1283V Dark Knight with retention bracket using antec 300 case

I could probably go higher with the Q6600, only thing is my board is holding me back. My board can't seem to go past 400 FSB with no chip no matter what. I've tried lowering multi and going higher than 400FSB but crashes instantly or keeps restarting post. Could be the board is defective, it was an Open box P43 Gigabyte from newegg.

 

[EarthDog]

Q9450 @ 3.8Ghz 1.33v.

This poll is just.....not right. Those are all completely different chips and their voltage limits and 24/7 settings are not even close. Oh well.

 

[freeagent]

so then...

request a new poll with cpu's that are more relevant to the times

 

[Phatboygeo]

Processor: Q6600
Speed: 4.12/4.18
Voltage: 1.49-1.54
Temperature: 39 -72
Load program: SIW
Cooling: TrUE - Scythe Sflex 1700rpm 120mm